Laser Printers

Card Stock & Label Guide

Laser Printers

September 2013 www.lexmark.com

Edition notice

September 2013

The following paragraph does not apply to any country where such provisions are inconsistent with local law: LEXMARK INTERNATIONAL,

INC., PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED

TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some states do not allow disclaimer of

express or implied warranties in certain transactions; therefore, this statement may not apply to you.

This publication could include technical inaccuracies or typographical errors. Changes are periodically made to the information herein; these

changes will be incorporated in later editions. Improvements or changes in the products or the programs described may be made at any

time.

References in this publication to products, programs, or services do not imply that the manufacturer intends to make these available in all

countries in which it operates. Any reference to a product, program, or service is not intended to state or imply that only that product,

program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any existing intellectual

property right may be used instead. Evaluation and verification of operation in conjunction with other products, programs, or services,

except those expressly designated by the manufacturer, are the user’s responsibility.

For Lexmark technical support, visit

http://support.lexmark.com.

For information on supplies and downloads, visit

www.lexmark.com.

Trademarks

Lexmark, Lexmark with diamond design, MarkVision, Optra, and Prebate are trademarks of Lexmark International, Inc., registered in the

United States and/or other countries.

Diamond Fine and WinWriter are trademarks of Lexmark International, Inc.

All other trademarks are the property of their respective owners.

GOVERNMENT END USERS

The Software Program and any related documentation are "Commercial Items," as that term is defined in 48 C.F.R. 2.101, "Computer

Software" and "Commercial Computer Software Documentation," as such terms are used in 48 C.F.R. 12.212 or 48 C.F.R. 227.7202, as

applicable. Consistent with 48 C.F.R. 12.212 or 48 C.F.R. 227.7202-1 through 227.7207-4, as applicable, the Commercial Computer Software

and Commercial Software Documentation are licensed to the U.S. Government end users (a) only as Commercial Items and (b) with only

those rights as are granted to all other end users pursuant to the terms and conditions herein.

Contents

Edition notice...............................................................................................2

Overview.....................................................................................................7

Introduction..............................................................................................................................................7

General information.....................................................................................8

Paper and label industry............................................................................................................................8

Printing volumes........................................................................................................................................8

Testing print material................................................................................................................................8

Design factors............................................................................................................................................9

Pick roller technology..............................................................................................................................11

Maintenance procedures........................................................................................................................14

Troubleshooting......................................................................................................................................14

Card stock..................................................................................................16

Weight.....................................................................................................................................................16

Grain orientation.....................................................................................................................................17

Coatings...................................................................................................................................................18

Offset powders........................................................................................................................................19

Labels.........................................................................................................20

Label characteristics................................................................................................................................20

Printing on labels.....................................................................................................................................20

Duplexing paper labels............................................................................................................................20

Primary rib pattern design guidelines for reference edge alignment.....................................................22

Label components...................................................................................................................................23

Label design guidelines...........................................................................................................................25

Printer specifications..................................................................................32

Lexmark C500n........................................................................................................................................32

Lexmark C510..........................................................................................................................................33

Lexmark C520, C522, and C524...............................................................................................................34

Lexmark C530, C532, and C534...............................................................................................................36

Lexmark C540, C543, C544, and C546dtn...............................................................................................38

Lexmark C720..........................................................................................................................................39

Contents 3

Lexmark C734 and C736..........................................................................................................................41

Lexmark C746 and C748..........................................................................................................................43

Lexmark C750..........................................................................................................................................45

Lexmark C752..........................................................................................................................................47

Lexmark C760 and C762..........................................................................................................................49

Lexmark C770, C772, C780, and C782.....................................................................................................51

Lexmark C792e, C792de, C792dte, and C792dhe...................................................................................53

Lexmark C910..........................................................................................................................................54

Lexmark C912..........................................................................................................................................56

Lexmark C920..........................................................................................................................................57

Lexmark C925..........................................................................................................................................59

Lexmark C935..........................................................................................................................................60

Lexmark C950..........................................................................................................................................62

Lexmark CS310n, CS310dn, CS410n, CS410dn, and CS510de.................................................................63

Lexmark CX310n, CX310dn, CX410e, CX410de, CX410dte, CX510de, CX510dhe, and CX510dthe.........65

Lexmark E120..........................................................................................................................................66

Lexmark E220..........................................................................................................................................67

Lexmark E230, E232, E234(n), E330, and E332n.....................................................................................68

Lexmark E238, E240, E240n, E340, and E342n........................................................................................69

Lexmark E250, E350, and E450n.............................................................................................................70

Lexmark E260, E260d, E260dn, E360d, E360dn, E460dn, E460dw, and E462dtn...................................71

Lexmark E320, E322................................................................................................................................72

Lexmark E321, E323................................................................................................................................73

Lexmark MS310d, MS310dn, MS410d, MS410dn, MS510dn, MS610dn, and MS610de........................74

Lexmark MS710 and MS711....................................................................................................................76

Lexmark MS810, MS811, and MS812......................................................................................................78

Lexmark MX310dn, MX410de, MX510de, MX511de, MX511dhe, MX610de, MX611de, and

MX611dhe...........................................................................................................................................80

Lexmark MX710, MX711, MX810, MX811, and MX812..........................................................................82

Lexmark T420..........................................................................................................................................85

Lexmark T430..........................................................................................................................................87

Lexmark T520, T522................................................................................................................................89

Lexmark T620, T622................................................................................................................................91

Lexmark T630, T632, T634......................................................................................................................94

Lexmark T640, T642, T644......................................................................................................................97

Lexmark T650, T652, T654, and T656dne................................................................................................99

Lexmark W812.......................................................................................................................................102

Contents 4

Lexmark W820.......................................................................................................................................103

Lexmark W840.......................................................................................................................................104

Lexmark W850.......................................................................................................................................106

Lexmark X203n and X204n....................................................................................................................107

Lexmark X215........................................................................................................................................109

Lexmark X264dn, X363dn, X364dn, and X364dw..................................................................................111

Lexmark X422........................................................................................................................................112

Lexmark X463de, X464de, X466dte, and X466dtwe.............................................................................114

Lexmark X500 and X502n......................................................................................................................115

Lexmark X543, X544, and X546dtn........................................................................................................116

Lexmark X548........................................................................................................................................118

Lexmark X560........................................................................................................................................119

Lexmark X642e......................................................................................................................................120

Lexmark X644e, X646e..........................................................................................................................123

Lexmark X651de, X652de, X654de, X656de, and X658de.....................................................................125

Lexmark X734, X736, and X738.............................................................................................................128

Lexmark X746 and X748........................................................................................................................130

Lexmark X782........................................................................................................................................132

Lexmark X792de, X792dte, X792dtfe, X792dtpe, X792dtme, and X792dtse........................................134

Lexmark X850, X852e, and X854e.........................................................................................................136

Lexmark X860e, X862e, and X864e.......................................................................................................138

Lexmark X925........................................................................................................................................140

Lexmark X940 and X945........................................................................................................................142

Lexmark X950........................................................................................................................................143

Optra plus, 4039, 4029, 4019, WinWriter 600 printers.........................................................................144

Optra C..................................................................................................................................................147

Optra C710............................................................................................................................................148

Optra Color 1200...................................................................................................................................149

Optra E, Ep.............................................................................................................................................150

Optra E310, E312...................................................................................................................................151

Optra Es special media printer..............................................................................................................152

Optra K 1220.........................................................................................................................................153

Optra M410, M412................................................................................................................................154

Optra N..................................................................................................................................................156

Optra S...................................................................................................................................................157

Optra SC 1275........................................................................................................................................159

Optra T..................................................................................................................................................160

Contents 5

Optra W810...........................................................................................................................................163

Glossary...................................................................................................165

Index........................................................................................................169

Contents 6

Overview

Introduction

This document provides guidelines to help you select appropriate print materials for the following Lexmark laser

printers.

Series Printer models

4019 All

4029 All

4039 10 plus All

4039 12C All

C series C500, C510, C520, C522, C524, C530, C532, C534, C540, C546dtn, C543, C544, C720, C734, C736,

C746, C748, C750, C752, C760, C762, C770, C772, C780, C782, C792e, C792de, C792dte, C792dhe,

C910, C912, C920, C925, C935, C950, CS310n, CS310dn, CS410n, CS410dn, CS510de, CX310n,

CX310dn, CX410e, CX410de, CX410dte, CX510de, CX510dhe, CX510dthe

E series E120, E220, E230, E232, E234(n), E238, E240, E250, E260, E320, E321, E322, E323, E330, E332n,

E340, E342n, E350, E360, E450, E460, E462dtn

M series MS310d, MS310dn, MS410d, MS410dn, MS510dn, MS610dn, MS610de, MS710, MS711, MS810,

MS811, MS812, MX310dn, MX410de, MX510de, MX610de, MX611de, MX611dhe, MX710, MX711,

MX810, MX811, MX812

Optra

All

T series T420, T430, T520, T522, T620, T622, T630, T632, T634, T640, T642, T644, T650, T652, T654, T656dne

W series W812, W820, W840, W850

WinWriter

600

4035 5W

X series X203, X204, X215, X264, X363, X364, X422, X463, X464, X466, X500, X502, X543, X544, X546dtn,

X548, X560(n), X642e, X644e, X646e, X651, X652, X654, X656, X658, X734, X736, X738, X746, X748,

X782, X792de, X792dte, X792dtfe, X792dtpe, X792dtme, X792dtse, X850, X852e, X854e, X860e,

X862e, X864e, X925, X940, X945, X950

The information supplied here supersedes other information relating to card stock and labels included with your printer.

See other printer documentation for detailed information about the paper, envelopes, and transparencies suitable for

your printer.

In addition to printer‑specific media recommendations, this document also explains design factors to consider when

purchasing all types of print materials. For definitions of industry terms, see

“Glossary” on page 165. If you have specific

stock or design questions, then contact your print materials supplier.

See your printer documentation for general printing information and terms. For technical assistance contact numbers,

see the printer registration card, information on the printer CD, or visit the Lexmark Web site at

http://support.lexmark.com.

Note: Always test print materials thoroughly before buying large quantities. Doing so will help you avoid unexpected

problems when you begin regular printing.

Overview 7

General information

Paper and label industry

The paper and label industry includes manufacturers, converters, and distributors.

• Manufacturers produce the base stock. If the base is for labels, then manufacturers may ship it on large rolls or in

a cut‑sheet form.

• Converters take the base stock and convert it into cut‑sheet products. Converters may work from rolls with or

without the adhesive applied. They may also take a base stock and convert it to meet their customers' specifications.

The conversion process includes, but is not limited to, cutting the stock to size, perforating the stock, die‑cutting,

and applying inks and topcoats. Converters work with their customers to convert the base material into a cut‑sheet

product designed for use in laser printers.

• Distributors are generally the direct link to the customer.

As needs and prices change, distributors may work with different converters and converters may work with different

manufacturers. Most businesses follow accepted industry conventions, but specifications, standards, formulations, and

processes may vary with time or with different companies.

As a result, labels or paper that worked well in the past may suddenly create printing problems because of a change in

material or process.

Some large businesses perform all three functions, from manufacturing to distribution. These companies may offer

greater expertise and product consistency than companies that concentrate on one facet of the process.

Printing volumes

Printing numerous sheets of card stock or labels in a short period of time can create printing problems. Continuous

printing on labels, for example, may result in more frequent service calls. The glue on the labels can be squeezed out

by the rollers in the printer and contaminate other printer parts. Most labels and card stock have cuts or perforations

that can be abrasive if not ironed or flattened.

Special media, in general, have rough coatings and are thicker.

Proper printer maintenance can help you avoid these problems. For information about maintaining your printer, see

“Maintenance procedures” on page 14.

Testing print material

Consider the following factors when choosing print materials:

• Physical characteristics of the base stock and the manufacturing processes, which are dependent on the vendor,

may change over time.

• The quality of print materials can also affect printer reliability and downtime. Using materials from converters or

vendors who are unfamiliar with laser printing may result in unsatisfactory print quality or other printing problems.

Once a design is finalized, test the print material before placing a large order to avoid costly mistakes.

General information 8

Your print materials supplier should be able to help develop your application or solve a problem you have with an

existing application. In addition, Lexmark has worked with several suppliers and has business partners in this field. For

technical assistance contact numbers, see the printer registration card, information on the printer CD, or visit the

Lexmark Web site at

http://support.lexmark.com.

Design factors

Print materials all have measurable characteristics that you need to consider when selecting or designing forms for

your particular application.

Basis weight

Basis weight is a term used to describe the weight in pounds of 500 sheets of paper (one ream). However, the weight

is determined based on the standard size of the paper, which may not be the purchased size. For example, the standard

size of 20‑lb bond paper is 17 x 22 inches, and a ream of 17 x 22‑inch 20‑lb bond paper weighs 20 pounds. If the

17 x 22‑inch 20‑lb bond paper was cut, creating four reams of 8.5 x 11‑inch paper, each ream would be labeled 20‑lb

bond paper but would only weigh five pounds.

If the same paper weighed 24 pounds, it would be called 24‑lb bond. The 24‑lb bond paper is thicker, heavier, and more

dense than the 20‑lb bond. Thicker paper means less paper can be placed in a tray, and paper that is heavier and more

dense may cause paper jams or feed reliability problems in some printers. Check the supported paper weights table

located in the printer documentation to verify that the paper basis weight being used is acceptable.

Not all basis weights are related to the same standard sheet size: for example, 70‑lb material can be lighter than 40‑lb

material if it is based on larger base size paper. The metric measurement of grams per square meter (g/m

) is a more

consistent way to compare weights and has been standardized by the International Organization for Standardization

(ISO). For more information, locate your printer in the “Printer specifications” chapter.

Your printer can accept a wide range of stock weights, but materials either too light or too heavy can cause printing

problems. Heavy and/or thicker materials may not heat quickly enough in the fuser, resulting in poor print quality. They

may also feed less reliably or skew due to their weight or rigidity. Conversely, lighter materials can wrinkle and jam in

the printer due to low beam strength (stiffness).

Depending on the orientation of the stock as it feeds through the printer, you may need to request that heavier materials

be cut grain short or grain long to provide flexibility in paper path turns. For more precise recommendations, locate

your printer in the “Printer specifications” chapter.

Dimensions

All printers have print material dimension limitations. See the printer documentation that came with your printer for

details. You can sometimes redesign forms to overcome these limitations. For example, if you use forms that are shorter

than the minimum length supported by your printer, you may be able to link two forms together when printing multiple

forms. An optional Universally Adjustable Tray designed for the Optra S, Optra T, and Lexmark T printer families prints

on a range of paper sizes including A6 and 3 x 5‑inch index cards, 3 x 7‑inch punch cards, and 4 x 6‑inch postcards.

Environment

Lexmark printers meet or exceed all industry emission regulations and standards. Continuous printing on some papers

or other media may create fumes that are not a problem with occasional printing. Make sure your printer is located in

a well‑ventilated area.

Temperature and humidity can have a major impact on printing. Even small changes (such as from day to night) can

greatly affect feed reliability if the print material is just within the range of acceptability.

General information 9

We recommend that you condition stock while it is still in the original wrapper. To condition stock, store it in the same

environment as the printer for 24–48 hours before printing to let the stock stabilize at the new conditions. You may

need to extend this time by several days if the storage or transportation environment is very different from the printer

environment. Thick stock may also require a longer conditioning period because of the mass of the material.

If you remove the wrapper from the stock before you are ready to load it in the printer, the stock may develop uneven

moisture content that can cause curl. Prior to loading your stock, we recommend that curl not exceed 3 mm (0.125 in.).

Lighter materials, such as paper labels and some integrated forms, are more likely to have printing problems if curl is

present.

Most label manufacturers recommend printing in a temperature range of 18–24°C (65–75°F) with relative humidity of

40–60%. Lexmark printers are designed to operate in a temperature range of 15.5–32°C (60 to 90°F) with relative

humidity of 8 to 80%. Printing in an environment outside these recommendations may cause jams, feeding problems,

reduced print quality, and predispensing (peeling) labels.

Inks (preprinted stock)

Preprinted stock introduces semi‑liquid and volatile components to the high temperatures and pressure used in the

laser printing process. Preprinted inks and colorations must withstand a fuser temperature up to 225°C (437°F) and

pressure up to 25 psi without contaminating the printer or creating hazardous fumes.

Thermography inks are not recommended. Thermography inks have a waxy feel and the printed image appears raised

above the surface of the print material. These inks can melt and damage the fuser assembly.

Preprinted inks must also be abrasion resistant to reduce ink dust and ink contamination in the printer. If you are

printing over a preprinted area, the ink must be receptive to toner to ensure adequate fusing.

All preprinted inks must be thoroughly dry before using printed materials. However, we do not recommend using offset

powders or other foreign materials to speed drying. Check with your converter, or the manufacturer or vendor of the

ink you plan to use, to determine if the ink is compatible with laser printers that heat the ink to 225°C (437°F).

Perforations and die‑cuts

If your form has perforations, the perforation line should stop 1.6 mm (0.06 in.) from each edge of the form to avoid

separating the form in the printer path, resulting in a jam. The location of the perforation affects initial pick strength.

Perforations closer to the edge may increase the number of jams. For pressure‑sensitive materials such as labels,

minimize the number of perforations that go through the backing material, or liner, since these can also affect the

strength of the form.

Perforations should be ironed so the print material lies flat, reducing nesting of forms. Edges should be smooth and

clean with no roll‑over. Laser

‑

perfs (also known as micro

‑

perfs or data

‑

perfs) provide greater stability and are preferred.

These smaller perforations do not normally nest or create excessive paper dust and debris. Make sure paper chaff and

dust created during the conversion process are removed before packaging.

If perforations tent, or crease at the perforation line, the perfs may break, causing a paper jam. Tenting may increase

skew, cause double‑sheet feeding, or smear the toner on the print material before fusing, resulting in poor print quality.

To reduce tenting, use micro‑perfs. If the print material is lightly snapped as it moves through the printer, the

perforations should hold without breaking.

Die

‑

cutting is used to create shapes in a label or a card stock design. When designing labels, round all corners to prevent

delamination of the labels, and avoid cuts through the liner (anvil cuts). Back splits and pop‑out windows are also not

recommended.

If perforations or die‑cuts are part of the design of the print material, ties are recommended. These small uncut areas

(approximately 1.6 mm or 0.06 in.) help stabilize the form and prevent tearing at perforations and die‑cuts during

printing.

General information 10

For areas with die‑cuts or perforations that create a small end product, or where die‑cuts or perforations intersect, ties

on the corners of the design provide added stability. Ties may be located anywhere along perforations or die‑cuts. For

pressure‑sensitive products, ties help prevent the labels from peeling off the liner while in the printer. Ties cannot,

however, be used to compensate for inadequate release strength of the adhesive in label designs.

For specific perforation and die‑cut guidelines for your printer, locate your printer in the “Printer specifications” chapter.

Debossing and embossing

Avoid debossing and embossing materials. Embossing leads to nesting and double‑sheet feeds, and the fusing process

significantly reduces the height of the raised image. Printing too close to embossments results in poor print quality and

poor fuse grade.

Metallics

We do not recommend using metallics in forms, whether in inks or other materials, due to their conductivity and their

ability to bleed charge. This can interfere with toner transfer and cause poor print quality.

Basic form design

When designing forms, include a non‑print area of 8.38 mm (0.33 in.) at the top and bottom of the form and 6.35 mm

(0.25 in.) on both sides of the form.

In general, portrait orientation is the preferred layout, especially if you are printing bar codes. If your forms require

landscape orientation, be aware that variations in paper path speed may produce spacing variations when printing bar

codes.

Note: We do not warrant uninterrupted or error‑free operation of a product. Warranty service does not include

repair of failures caused by:

• modification or attachments

• accidents or misuse

• unsuitable physical or operating environment

• maintenance by any unauthorized (non‑Lexmark) servicer

• operation of a product beyond the limit of its duty cycle

• failure to have installed a maintenance kit as specified (if applicable)

• use of printing media outside of Lexmark specifications

• use of non‑Lexmark supplies (such as toner cartridges and/or inkjet cartridges)

• use of non‑Lexmark product or component

Pick roller technology

Some printers have an auto compensator which feeds paper more reliably than the corner buckler system used by

earlier printer models. The auto compensator has two rollers that touch the media. Avoid placing deep perforations in

these areas since the media may nest, causing multiple sheets to feed. Perforations that could cause nesting and tenting

should fall outside the pick roller area on the leading edge of the media. This is different from the 0.50‑inch space we

recommend leaving at the top of the form for printers with a corner buckler system. You may want to use micro‑perfs

to avoid nesting problems. For more information, see

“Perforations and die‑cuts” on page 10.

General information 11

For the following printers, make sure perforations fall outside the 0.3–0.79‑inch area on the leading edge of the media:

Optra S, Optra T, T520, T522, T620, T622, T630, T632, T634, T640, T642, T644, T650, T652, T654, T656dne, X203, X204,

X264, X363, X364, X463, X464, X466, X543, X544, X546dtn, X560n, X642e, X644e, X646e, X651, X652, X654, X656, X658,

X734, X736, X738.

General information 12

For the following printers, make sure perforations fall outside the 0.31–1.05‑inch area on the leading edge of the media:

C520, C522, C524, C530, C532, C534, C540, C543, C544, C546dtn, C734, C736, C750, C752, C760, C762, C770, C772,

C780, C782, C792e, C792de, C792dte, C792dhe, CS310n, CS310dn, CS410n, CS410dn, CS510de, CX310n, CX310dn,

CX410e, CX410de, CX410dte, CX510de, CX510dhe, CX510dthe, X792de, X792dte, X792dtfe, X792dtpe, X792dtme, and

X792dtse.

General information 13

For the following printers, make sure perforations fall outside the 0.12–0.91‑inch area on the leading edge of the media:

MS710, MS711, MS810, MS811, MS812, MX710, MX711, MX810, MX811, and MX812.

Pick Roller Location

0.12 in.

0.91 in.

0.56 in.

1.08 in.

2.76 in.

3.28 in.

Direction of Feed

Maintenance procedures

Note: These procedures apply only to mono laser printers.

If print quality begins to degrade when printing on vinyl labels, then do the following:

1 Print on five sheets of paper.

2 Wait approximately five seconds.

3 Print on five more sheets of paper.

To maintain printer feeding reliability, repeat this cleaning process every time you replace the toner cartridge.

Note: Failure to follow maintenance procedures for your printer could cause jams, poor print quality, feeding

problems, and fuser problems.

Troubleshooting

The following table provides solutions to some common card stock and label problems. For more troubleshooting

information, see your printer documentation.

General information 14

Problem Solution

Print on heavy stock is

blurred or out of focus.

Make sure the Paper Type setting is correct for your print material.

Note: Card stock in excess of 203 g/m

(54‑lb bond) may not produce acceptable print

results.

Print on five sheets of paper, wait for approximately five seconds, and then print five more

sheets of paper to remove any toner that may have accumulated.

Toner rubs off the page. Make sure the Paper Type setting is correct for your print material.

Use material that is lighter than 300 g/m

Print on five sheets of paper, wait for approximately five seconds, and then print five more

sheets of paper to remove any toner that may have accumulated.

Printing shows voids. Change the Paper Type to Plain Paper.

Print on five sheets of paper, wait for approximately five seconds, and then print five more

sheets of paper to remove any toner that may have accumulated.

General information 15

Card stock

Card stock is a rigid, stiff material that can have a wide variety of constructions. Orientation of paper fibers (grain

direction), moisture content, thickness, texture, and other properties can significantly impact printing, as can

preprinting, perforation, creasing, and other features common to forms. For example, preprinting introduces

semi‑liquid, volatile components that must withstand the high temperatures used in laser printing. Perforation and

creasing may cause nesting, or interlocking, which can cause paper jams and double-sheet feeds.

In general, we recommend a single‑ply construction of 100% chemically‑pulped wood with a vellum finish. Before

purchasing large quantities of card stock, make sure you test samples of the print material in your printer.

Weight

The weight of card stock significantly affects the print quality and feed reliability of the stock. Specify the correct basis

weight of a stock. For more information, see

“Basis weight” on page 9.

Basis weight is the weight in pounds of one ream, or 500 sheets, of paper. Since the sheet size varies from one type of

stock to another, basis weights are not always easily comparable. For example, an office supply store has 8.5 x 11‑size

cover stock (80 lb Bristol) and 8.5 x 11‑size card stock (90 lb Index) side by side on the shelf. Both papers are manufactured

by the same company, and a basis weight comparison indicates the card stock (90 lb Index) is heavier than the cover

stock (80 lb Bristol). In this case, however, the cover stock (80 lb Bristol) is actually heavier than the card stock (90 lb

Index).

Before the two types of paper were cut into 8.5 x 11‑size pages, the card stock was a larger sheet size than the sheet

size of the cover stock. When the papers were cut during the manufacturing process into 8.5 x 11‑size pages, more

reams (500 sheets) of paper were received from the card stock sheets than from the cover stock sheets. This makes

the weight of the cover stock heavier than the weight of the card stock.

It is easier to compare the cover stock metric weight (g/m

) against card stock metric weight (g/m

). If you look at the

metric weights of the two stocks in the previous example, it is immediately evident that 80 lb Bristol cover stock

(176 g/m

) is heavier than 90 lb Index card stock (163 g/m

Not all printers are able to print on cover stock. This is because cover stock is usually thicker and not able to make the

turns in the printer paper path. This causes paper jams and sometimes causes the paper to feed incorrectly. Also, when

using a laser printer, toner is pulled onto the paper through an electrical charge. If the paper is too thick, then there

may not be enough voltage to pull the toner onto the paper properly, resulting in poor print quality.

To determine if your printer supports cover stock, see the section for your printer in the "Printer specifications" chapter

and review the supported paper type information. You can also view the supported paper types in the documentation

that came with your printer.

Use the following table to compare the weights of various types of card stock.

Metric

equivalent

(g/m

)

Basis weight (lbs/ream)

Bond

431.8 x

558.8 mm

(17 x 22 in.)

Offset

635 x

965.2 mm

(25 x 38 in.)

Cover

508 x

660.4 mm

(20 x 26 in.)

Printing Bristol

571.5 x 889 mm

(22.5 x 35 in.)

Index Bristol

647.7 x 774.7 mm

(25.5 x 30.5 in.)

Tag

609.6 x

914.4 mm

(24 x 36 in.)

75 20 50 — — — 50

90 24 60 — — — —

Card stock weights may vary ± 5%.

Card stock 16

Metric

equivalent

(g/m

)

Basis weight (lbs/ream)

Bond

431.8 x

558.8 mm

(17 x 22 in.)

Offset

635 x

965.2 mm

(25 x 38 in.)

Cover

508 x

660.4 mm

(20 x 26 in.)

Printing Bristol

571.5 x 889 mm

(22.5 x 35 in.)

Index Bristol

647.7 x 774.7 mm

(25.5 x 30.5 in.)

Tag

609.6 x

914.4 mm

(24 x 36 in.)

105 28 70 — — — —

108 29 — 40 — — —

118 31 80 — — — —

120 32 — — — 67 74

131 35 90 — — — —

135 36 — 50 — — —

148 39 100 — — — —

163 43 — 60 — 90 100

176 47 120 65 — — —

199 53 — — 110 110 —

203 54 — — — — 125

Card stock weights may vary ± 5%.

Depending on the printer, material thicker than 0.30 mm (0.012 in.) may present feed reliability problems, and material

thicker than 0.17 mm (0.007 in.) may reduce print quality. Contact your supplier to determine the weight of any card

stock you currently use.

See the individual printer specifications in this document for more information about the card stock weights your printer

supports.

Grain orientation

Grain refers to the alignment of the paper fibers in a sheet of paper. Grain is either grain short, running the width of

the paper, or grain long, running the length of the paper.

The orientation of the grain contributes to the rigidity of card stock and affects feed reliability. The recommended grain

orientation depends on the weight of the stock and whether the printer feeds the stock short edge first or long edge

first. For lighter card stocks, grain long is recommended to reduce potential curl problems. Curl may decrease the ability

of the form to move reliably through the printer.

Most printers feed paper short edge first. If your printer supports larger paper sizes, such as 11 x 17 in. or A3, it may

feed some paper sizes long edge first. See your printer documentation for more information.

For materials fed short edge first:

Card stock 17

Grain short is recommended for stock heavier than 135 g/m

Feed

directio

Grain

direction

Grain long is recommended for stock lighter than 135 g/m

Feed

directio

Grain

direction

For materials fed long edge first:

Grain long is recommended for stock heavier than 135 g/m

Feed

direction

Grain

direction

Grain short is recommended for stock lighter than 135 g/m

Feed

direction

Grain

direction

See the individual printer specifications in “Printer specifications” on page 32 for more information about the

recommended grain direction for card stock you use with your printer.

Coatings

Surface texture and coatings on card stock significantly affect toner adhesion (fuse grade), print quality, and feed

reliability. We recommend a vellum finish for the best printing performance. We do not recommend glossy coatings

and slick surfaces or surfaces that mimic laid finishes (glossy paper, not glossy card stock, is acceptable for some printers).

Paper smoothness also affects print quality. If the paper is too rough, the toner does not fuse to the paper properly; if

the paper is too smooth, it can affect feed reliability. We recommend smoothness to be between 100 and 400 Sheffield

points (150–250 is optimal). Using media higher than 300 Sheffield could result in printing degradation.

Card stock 18

Offset powders

We do not recommend using offset powders or other foreign materials to speed drying. Offset powders are used by

print shops to prevent printed pages from sticking together. Powder is usually sprayed on the printed page right before

it reaches the stacker on the offset printing press. This powder provides an intermediate layer between two sheets of

paper, preventing ink from transferring from one sheet to another.

Card stock 19

Labels

Labels , or pressure‑sensitive materials, are multi‑ply materials that contain various combinations of face sheets

(printable stock), adhesives, and removable protective backings (liners). These layers can result in thick materials that

are difficult to handle.

Labels are among the most difficult print materials for any printer to reliably feed and print. Factors such as heat,

pressure, and paper path could make printing on labels quite challenging. For example, temperatures near 225°C (437°F)

[temperatures vary between printers; check the section for your specific printer] and pressures to 25 psi can be

necessary for the fusing process. Heavy label stock can absorb heat, which in turn affects toner adhesion and print

quality and causes problems such as delamination.

Note: To prevent labels from peeling off or delaminating, make sure the release strength of the labels is sufficient to

withstand the temperature and pressure extremes generated during printing.

Label characteristics

The materials used to construct labels have a wide range of properties that can affect printing. Volatile components

are in the label materials and in the adhesive itself. We recommend that volatile emissions from the label, up to 160°C

(320°F), should be a minimal amount. The volatile components, which have low boiling point, produce emissions when

heated in the fuser and could emit vapors that can damage the printer.

Preprinted inks can also cause printer contamination, and may be present on one or both sides of the label sheet.

Follow the recommended label design guidelines to prevent labels from peeling off, which could cause jams. The label

or adhesive could also melt if the sheet is jammed in the fuser.

Review label designs with a converter or a vendor who has extensive knowledge about labels and laser printers to

ensure that you are using the proper type of labels.

Before purchasing large quantities of labels, make sure you extensively test the labels with your printer.

Printing on labels

Print on full label sheets only. Sheets with missing labels could peel off during printing and result in a paper jam. Partial

sheets can also leave adhesive marks on the printer and cartridge, which could void the printer and cartridge service

warranties.

Do not feed labels through the printer more than once. Doing so may contaminate the cartridge and other components

with adhesive.

Depending on your printer model and the number of labels being printed, printing labels may require special printer

maintenance. For specific maintenance information, see the documentation that came with your printer.

For more information about printing on labels, see the section for your printer in the “Printer specifications” chapter.

Duplexing paper labels

Labels are not typically duplexed because of their special construction. However, printing on both sides of the label

sheet may be possible if certain design, construction, and usage guidelines are followed.

Labels 20

When developing a paper label for duplexing, the converter should make sure that the label is designed to protect

against contamination or buildup. Contamination could result in paper feed problems and paper jams.

We recommend the use of label sheets that have a non-adhesive border around the label area. Make sure that the

release strength is enough to withstand temperatures of 225°C (437°F) and pressure up to 25 psi. The ability to withstand

these factors is important because the label sheet will be subjected to these twice.

Use label ties whenever possible. These small uncut areas (approximately 1.6 mm or 0.06 in.) help stabilize the label

sheet and prevent tearing at perforations and die-cuts during printing. Label ties also prevent labels from predispensing

in the printer.

The slits and cuts in the labels expose the adhesives to the printer. For best results when duplexing labels, position the

label sheet so the slits and cuts are not aligned with the ribs in the duplex or redrive areas of the printer. This eliminates

any contact points between the label adhesive and the printer, thereby preventing any adhesive contamination in the

printer. The following graphics show the rib locations for the Optra S, Optra T, and Lexmark T, respectively.

Optra S rib locations (rib width = 2 mm):

20 mm

21 mm

27 mm

15.5 mm

21.5 mm

28 mm

26 mm

17 mm

15 mm

Reference Plate

22 mm

Optra T and Lexmark T rib locations (rib width = 2 mm):

16 mm

11 mm

15 mm

13 mm

16 mm

17 mm

26 mm

18 mm

12 mm

20 mm

12 mm

15 mm

4.02 mm

Reference Plate

Labels 21

Load label sheets with the label end first. Use grain long paper instead of grain short paper, which tends to curl easily.

If a converter develops a grain short label sheet for duplexing, then test the sheet first to make sure it works satisfactorily.

Note: We recommend testing any material with your application and printer before purchasing large quantities.

To use the duplex label application, you must install a special fuser wiper.

Printer Fuser wiper part number

S1855, T612, T614, T520, and T522 99A1082

T620 and T622 18A1467

T630, T632 and T634 56P2109

T64x, X644e, and X646e 40X2666

T65x and X65x 40X2666

The wiper makes it possible to print on both sides of paper labels specifically designed for duplexing. You may also use

the wiper when using the printer to print on one side of a label sheet or both sides of a sheet of paper. When ordering

a new cartridge, be sure to order the cartridge that includes the correct fuser wiper.

Primary rib pattern design guidelines for reference edge

alignment

The function of the primary rib pattern is to provide the best support to the media during transport. If it is known that

the media will be touching a certain surface, then that surface must contain the primary rib pattern.

The feed path should guide the leading edge of the media into the primary guide surface and not the secondary surface.

This provides a determinate location for the leading edge of the media on the guide surface that provides the best

support.

The incidence angle of the leading edge of the media as it touches the primary guide surface should be no more than

30°. This eliminates media stubbing on the guides and reduces the amount of energy input into the media by the guide.

The primary rib pattern is to have the rib support extending out to between 3 to 10 mm from the edge of the paper

and 2 to 10 mm from the edge of the envelopes. This keeps the corners of the media stiff so that it cannot fold and

catch other surfaces in the printer. It also prevents the corners of the media from catching the inside surface of a paper

path rib.

The primary rib pattern should not have any ribs closer than 3 mm to the outside edge of paper and envelopes. This

keeps the media from stubbing into a rib that is too close to the edge of the media.

The maximum rib spacing of the primary rib pattern should not be greater than 20 mm. This keeps the leading edge of

the media flat as it moves through the system.

Labels 22

The following are the rib locations for the Lexmark MS710, MS711, MS810, MS811, MS812, MX710, MX711, MX810,

MX811, and MX812 printer models.

Referenc e

Edge

221.6

204.0

189.6

170.5

153.0

134.0

115.6

94.4

83.5

68.5

52.5

36.5

20.5

5.6

0.6

0.4

0.2

0.1

Label components

Labels are composed of three basic parts: the liner, the adhesive, and the face sheet. Labels may also have topcoats

that affect printing. Choosing appropriate materials for each of these label components will help ensure reliable printing.

Liners

The liner, also known as the carrier or backing, is the material onto which the label is attached. The liner carries the

label through the printer and directly affects feed reliability. Liner weights and construction vary based on the printable

face stock used. For more information, see

“Face sheet (printable stock)” on page 25.

Tissue‑backed, plain bond, or bond‑like, porous, lay‑flat liners are preferred. Liners constructed for use with high‑speed

laser printers (50 or more pages per minute) may not produce acceptable results.

A liner should bend easily and go back to its original flat state when released. If the form remains bent, then it may

cause paper jams or damage to the edge of the sheet, particularly in earlier printer models using a corner buckler rather

than an auto compensator to separate the sheets. The following table shows which printers use a corner buckler and

which use an auto compensator.

Note: If your printer is not listed here, then contact your Lexmark representative to verify which method your

printer uses to separate sheets of labels.

Labels 23

Printers using a corner buckler Printers using an auto compensator

• 4019, 4029, 4039, 4049

• Lexmark E220, E320, E321, E322,

E323, T420, W820, X422

• Optra 12L, 12R, Lxi, Lx, Rx

• Optra R+, Rt+, Lx+, Lxi+

• Optra C, Optra Color 1200, Optra N

• Optra M410, M412, W810

• C910, C912, C920

• Lexmark E230, E232, E234(n), E330, E332n, E260, E360, E460, C510, C520,

C522, C524, C530, C532, C534, C540, C734, C736, C750, C752, C760, C762,

C770, C772, C780, C782, C792e, C792de, C792dte, C792dhe, C935, CS310n,

CS310dn, CS410n, CS410dn, CS510de, CX310n, CX310dn, CX410e, CX410de,

CX410dte, CX510de, CX510dhe, CX510dthe, T520, T522, T620, T622, T630,

T632, T634, T640, T642, T644, T650, T652, T654, T656dne, X203, X204, X215,

X264, X363, X364, X463, X464, X466, X540, X642e, X644e, X646e, X651, X652,

X654, X656, X658, X734, X736, X738, X792de, X792dte, X792dtfe, X792dtpe,

X792dtme, X792dtse, W840

• Optra S 1250, S 1650, S 2450

• Optra S 1255, S 1625, S 1855, S 2455

• Optra Se 3455

• Optra T610(n), T612(n), T614(n), T616(n)

Some liner materials used in pressure‑sensitive constructions are called label papers. Label papers are either machine

finish (MF) or English finish (EF) papers that are calendered, supercalendered, or coated on one side. An MF has varying

degrees of surface smoothness. The smoothness is determined by the number of times the paper passes through the

rollers (wet or dry) during manufacturing. An EF is uncoated and low gloss in appearance. Label papers may also be

used as the face sheet for pressure‑sensitive paper products, such as the materials used in dual web forms construction.

Supercalendering produces high gloss surfaces that may be slick. Some supercalendered liners are difficult for printers

to pick and feed reliably. We do not recommend using supercalendered liners designed for high‑speed laser printers

(50 or more pages per minute).

Some pressure‑sensitive constructions use Kraft liners or bleached Kraft liners. Kraft liners are made from sulfate pulp

and are MF or machine glazed (MG). Most MG papers have a high gloss appearance. High gloss, glazed surfaces may

increase skew and are more difficult for the printer feed mechanism to handle reliably. Some Kraft liners may produce

acceptable results; however, we strongly recommend extensive testing of pressure‑sensitive constructions using Kraft

liners.

Tissue‑backed or plain bond liners reduce toner contamination inside the printer and improve feed performance. Slick,

non‑porous liners are harder to feed and increase toner buildup in the fuser and on the backup roll. Rough backings,

on the other hand, can increase paper path friction, which can cause skew and paper jams. The face material of the

liner needs to have a melt temperature that can also withstand the fuser temperatures of nearly 225°C (437°F). Since

there is a stripped area of a maximum of 3 mm, this can expose the face material to these temperatures and could

cause melting or contamination in the fuser.

Excessive paper dust or chaff associated with the liner may affect print quality. If a liner material produces excessive

paper dust or chaff during the conversion process, some of this debris may be packaged with the material and end up

in the printer. Liner materials that produce excessive paper dust or chaff as they feed through the printer may also

affect print quality.

Your forms supplier can provide additional information on liners.

Adhesives

There are three basic types of label adhesives: removable, permanent, and semi‑permanent (cold temp). All types, with

proper design, can be used with your printer. Acrylic‑based adhesives are generally preferred for cut‑sheet label

printers.

Labels 24

The major adhesive‑related printing problem is printer and cartridge contamination. The adhesives are semi‑liquid and

may contain volatile components. If the sheet jams in the fuser, the adhesive can melt, thereby contaminating parts

of the printer or releasing fumes. To avoid exposing adhesive to the paper path guides, drive rollers, charge roller,

photoconductor drum, transfer roller, and detack fingers, use full label sheets.

Zone coating means placing the adhesive only where needed. Paper labels and integrated forms typically use zone

coating. In addition, a non‑adhesive border of 1 mm (0.04 inches) around the outside edge of the label sheet generates

good results. Check with your adhesive manufacturer or forms supplier for more information about designing labels

for your printer.

A stripped edge matrix along the outer border of the stock, combined with adhesive that does not ooze, helps prevent

adhesive contamination. This design requires a stiffer backing material to prevent damage when the sheet is aligned

on the reference edge. Generally, vinyl and polyester labels are well‑suited for this design. Paper and dual web designs

may require testing to determine which backing produces good results. For more information on matrices, see

“Label

design guidelines” on page 25.

Make sure the release strength is adequate so labels stay attached to the liner and do not peel off in the printer.

Adhesives must be able to withstand pressures to 25 psi and fuser temperatures of 225°C (437°F) without delaminating,

creating hazardous fumes, or oozing around edges of labels, perforations, or die‑cuts. Shear strength should be strong

enough to prevent adhesive stringers. For more information, contact your forms supplier.

Face sheet (printable stock)

Paper, vinyl, and polyester are the most common materials used for printable stock. Your forms supplier can provide

information on whether the printable stock you want to use can withstand temperatures up to 225°C (437°F) and

pressures up to 25 psi. Carefully test the stock to make sure it functions satisfactorily with your printer.

Note: Temperatures vary by printer. For more information, see the section for your printer.

Topcoats

Topcoats for non‑paper labels may be either water‑based or solvent‑based. Avoid topcoats containing chemicals that

emit hazardous fumes when heated or exposed to pressure. Topcoats affect the print quality, feed reliability, and

adhesion of toner to the face sheet. Topcoats must be able to withstand temperatures up to 225°C (437°F) and pressures

up to 25 psi for 100 milliseconds to prevent fuser damage.

Note: Temperatures vary by printer. For more information, see the section for your printer.

Water‑based topcoats tend to be more conductive than solvent‑based topcoats and are more difficult to fuse. With

some water‑based topcoats and heavy liners, the fuse grade may fall below acceptable levels. Solvent‑based topcoats

tend to be lower in conductivity than water‑based topcoats. With some solvent‑based topcoats, fuse grade is within

acceptable levels when heavier liners are used.

Print quality may degrade when using topcoats on labels with heavier liners. Using a lighter liner may reduce the

appearance of splatter. Carefully test the forms to make sure the topcoat functions satisfactorily with your printer.

Label design guidelines

Labels with a stripped edge matrix do not have the area around the outer edge of the cut sheet. Labels with a total

strip matrix do not have the die‑cut stock around and between the labels. This makes it easy to peel the labels from

the backing.

Butt cut labels are cut flush to one another, with no extra area between them. Avoid using butt cut labels without a

stripped edge matrix.

Labels 25

Die

‑

cut labels are cut with a non‑print area between each label. For best results, do not print within 2.3 mm (0.090 in.)

of the edge of the label, of the perforations, or of the die‑cuts of the label.

If you are using a butt cut or die‑cut label, then make sure adhesive contamination does not occur. Labels use varying

levels and types of adhesive, as well as a variety of liner materials and facestock papers. Adhesive can ooze from all

label stocks. Make sure die‑cuts are free of adhesive stringers. To prevent adhesive contaminations, use zone coating

or pattern adhesive with a non‑adhesive border of about 1‑mm (0.04‑in.) or larger.

If zone coating is not used, then we recommend a stripped edge matrix. The stripped edge matrix varies with the type

of face stock, liner, and adhesive materials. See the following table for stripped edge matrix guidelines. Measurements

may vary ±0.5 mm.

Face type Total weight of label Edge matrix removal Location of strip

Paper* (cut sheet or

dual web)

140–180 g/m

1.6 mm (0.0625 in.)

215.9 mm (8.5 in.) at leading edge

279.4 mm (11 in.) at driver edge

Vinyl

265–300 g/m

1.6 mm (0.0625 in.)

215.9 mm (8.5 in.) at leading edge

279.4 mm (11 in.) at driver edge

Polyester and other

face materials

Varies 1.6 mm (0.0625 in.)

1.6 mm (0.0625 in.)

215.9 mm (8.5 in.) at leading edge

279.4 mm (11 in.) at driver edge

* Use a non‑oozing adhesive.

Using cut sheet labels with adhesive applied to the edge of the sheet will contaminate your printer and your cartridge

and could void your printer and cartridge warranties.

When using pressure‑sensitive materials without zone coating, choose butt cut labels without any stringers and with

a stripped edge matrix. If a total strip matrix is in the design for the final product, then print before removing the matrix.

If the matrix must be removed before printing, then round all corners and make sure adhesive is not exposed.

The following diagram shows a recommended label design for Optra plus printers, 4039, 4029, and 4019, as well as the

T610, T520, T620, and T630 laser printers.

Note: The non‑print area may vary depending on the printer model.

Labels 26

Leading Edge

8.5 in.

215.9 mm

0.094 in.

2.4 mm

Liner edge

Stripped edge

0.125 in.

3 mm

Driver edge

11 in.

279.4 mm

0.06 in.

1.6 mm

Perforation end

Liner edge

Non-print area Non-print area

Non-print area

0.25 in.

6.35 mm

0.25 in.

6.35 mm

0.33 in.

8.38 mm

0.33 in.

8.38 mm

0.5 in.

12.7 mm

Waste strip 0.25 in (6.35 mm)

Waste strip

Top perforation

(Not drawn to scale)

Labels 27

The following diagram shows a recommended label design for the T640 and T650 laser printers.

Labels 28

The following diagram shows a recommended label design for laser printers, which use a different paper picking

mechanism.

Leading Edge

8.5 in.

215.9 mm

0.094 in.

2.4 mm

Liner edge

Stripped edge

0.125 in.

3 mm

Driver edge

11 in.

279.4 mm

0.06 in.

1.6 mm

Perforation end

Liner edge

Non-print area Non-print area

Non-print area

0.25 in.

6.35 mm

0.25 in.

6.35 mm

0.33 in.

8.38 mm

0.33 in.

8.38 mm

0.79 in.

20 mm

Top perforation

(Not drawn to scale)

Cut sheet paper labels

• Generally, cut sheet paper labels work well with your printer.

• Coating or sizing to make the paper liquid‑resistant decreases toner adhesion and increases the risk of toner

contaminating the fuser. At a minimum, paper labels should be equivalent in weight and rigidity to a 20‑lb

xerographic bond paper.

Dual web forms

• Constructing dual web forms involves joining together rolls of two different materials (usually pressure‑sensitive

paper and bond paper) and then converting to a cut sheet product.

• This construction requires a stripped edge matrix. The liner must be rigid enough to withstand the pick force of the

printer.

Labels 29

• The two materials must be thin enough for the sheet to lie flat in the paper tray. The differences in thickness may

cause the materials to curl down towards the leading edge of the form which can negatively affect feeding. For

more robust feeding, it is recommended that the leading label edge should be as thick as or slightly thicker than

the dual web overlap thickness to make sure the sheet lies flat in the tray. The form should be placed with the label

facedown in the tray. Orient the form in the tray so that the pressure‑sensitive area feeds into the printer first. The

form should have no adhesive exposed in the overlay area or anywhere along the front or back of the form.

• We recommend designing a non‑adhesive strip with a minimum width of 1 mm (0.04 in.) along the edges of the

overlay.

• To help prevent material from slipping in the fuser, we recommend knurling, which roughens up the exposed silicon

area at the glue joint.

• The face sheet of a dual web form is usually a paper pressure‑sensitive product; therefore, the guidelines for paper

labels are applicable to dual web forms.

• The following diagram shows the recommended dual web form design. The non‑print area may vary depending on

the printer model.

Leading edge

(8.5 in.)

0.0625 in.

1.6 mm

Liner edge

Stripped edge

0.0625 in.

1.6 mm

Reference edge

(11 in.)

Non-print area

Pressure-sensitive

Paper

0.33 in.

8.38 mm

Overlay

0.25 in.

6.35 mm

(Not drawn to scale)

Vinyl and polyester labels

• Vinyl labels work well within specified design parameters. Vinyls are heat‑sensitive, so the liners need to be thick

enough to absorb excess heat and prevent melting. A total strip matrix may cause adhesive contamination.

• Thin liners or weak pull strength may lead to labels peeling off the form inside the printer, which will require printer

servicing. For more information on recommended label designs, see

“Label design guidelines” on page 25.

Labels 30

• For Optra S, Optra T, and Lexmark T printers, a leading and trailing edge stripped area is recommended to be a

maximum of 3 mm. This area is recommended to prevent adhesive being close to the edge, which can contaminate

your printer.

• Certain materials used in label construction, which have liner face melt temperatures lower than the fuser

temperature, may require the leading and trailing edge stripped areas to be 1.6 mm maximum due to feeding

problems.

• It is preferred that the liner face be constructed with material that can withstand our fuser temperatures, which

eliminates the need for changing the stripped areas from 3 mm to 1.6 mm.

• If a 1.6‑mm stripped area is used, it is very important that the 1.6‑mm tolerance be held tightly. With a stripped

area of less than 1.6 mm, it is highly possible that adhesive contamination will occur.

• Vinyls are non‑absorbing, which leads to toner build‑up in the fuser that requires special maintenance. See the

documentation that came with your printer for specific information about maintaining your printer. Vinyls may

require a topcoat to ensure good toner adhesion.

• Polyester labels are less heat‑sensitive but are also non‑absorbing. Backings for polyester labels can be thinner, but

requirements for coatings and cleaning are similar to vinyl labels.

• It is recommended that when you run vinyl labels, you install a special oil fuser cleaner, P/N 99A0725 or 40X2665.

When you order a new cartridge, be sure to order the cartridge that will include the correct fuser cleaner.

Integrated forms

• To create integrated forms, the converter uses hot melt adhesives to apply the label adhesive and liner to a base

material (generally paper).

• Oil bleed, recognizable by a discolored face sheet, can be a problem with these forms. Oil may also migrate from

the top of the liner to the back surface of the liner while it is on the roll, before the conversion process takes place.

• The forms created from this material may then be slick, and the pick mechanism of your printer may be unable to

successfully move all the sheets from the tray into the printer. Jamming and misfeeds increase when oil is present

on the back of the liner.

• The adhesive on these forms is commonly patterned on two or four sides (that is, the forms have a non‑adhesive

border on either two or four edges). We recommend designing a 1‑mm (0.04‑in.) non‑adhesive border (zone coated)

on all four edges.

• When printing on integrated forms with a grain long base material, orient the form in the tray so the paper portion

of the form feeds into the printer first. Orient the pressure‑sensitive portion of the form toward the portrait left

edge.

• For integrated forms with a grain short base material, orient the form in the tray so the pressure‑sensitive portion

feeds into the printer first.

• Due to the unique construction of integrated forms, you may experience stacking problems in the output bin.

Contact your Lexmark marketing representative if you experience stacking problems with these forms.

Note: Test some forms before purchasing large quantities.

Labels 31

Printer specifications

Lexmark C500n

Limit label printing to occasional use of paper office labels designed for laser printers. The Lexmark C500n does not

support vinyl or polyester labels.

The Lexmark C500n supports 90–210‑g/m

(24–55‑lb) stock. Card stock and labels are supported from Tray 1 and Tray 2.

Tray 1 supports approximately 120 sheets of card stock and Tray 2 supports up to 250 sheets of card stock. The following

table lists the maximum weights supported.

Paper source

Card stock

(Grain short is preferred for papers over 135 g/m

) Labels*

Index Bristol Tag Cover Paper

Tray 1 (standard tray)

90–210 g/m

180 g/m

Tray 2 (optional tray)

90–210 g/m

180 g/m

* Vinyl labels are not supported.

Labels Width: 76.2–216 mm (3–8.5 in.)

Length: 123.8–355.6 mm (4.88–14 in.)

Weight:

180 g/m

(48 lb)

Thickness: 0.13–0.20 mm (0.005–0.008 in.)

Smoothness: 100–400 Sheffield*

* 150–250 Sheffield is optimal. Using media higher than 300 Sheffield could result in printing degradation.

Card Stock Weight:

163‑g/m

(90‑lb) Index Bristol

163‑g/m

(100‑lb) Tag

Up to 210‑g/m

(78‑lb) Cover

For more information on the supported media sizes, see the printer User's Guide on the publications CD.

Printer specifications 32

Lexmark C510

Limit label printing to occasional use of paper office labels designed for laser printers. The Lexmark C510 does not

support vinyl or polyester labels.

The Lexmark C510 supports stocks up to 176 g/m

. Feed labels from the standard tray only, which holds up to 80 sheets

of labels or up to 120 sheets of card stock.

The following table lists the maximum weights supported.

Paper source

Card stock Labels

Index Bristol Tag Cover Paper Vinyl

Tray 1 (standard tray)

163 g/m

176 g/m

——

Tray 2 (optional tray)

163 g/m

176 g/m

——

Multipurpose feeder

163 g/m

176 g/m

131 g/m

—

Labels Width: 105–216 mm (4.1–8.5 in.)

Length: 220–297 mm (8.7–11.7 in.)

Weight:

120–163 g/m

Thickness: 0.13–0.20 mm (0.005–0.008 in.)

Smoothness: 100–400 Sheffield*

* 150–250 Sheffield is optimal. Using media higher than 300 Sheffield could result in printing degradation.

Card stock Weight:

Up to 163 g/m

Index Bristol (90 lb)

Up to 163 g/m

Tag (100 lb)

Cover stock Weight:

Up to 176 g/m

(65 lb)

Card stock and label guidelines

When printing on labels:

• Feed labels from Tray 1 only.

• Use only paper labels. Do not use vinyl labels.

Printer specifications 33

• Use only label sheets that have no gaps between the labels.

Acceptable labels

Unacceptable labels

• Recommended labels are Avery 5260.

• From the operator panel or from MarkVision

Professional, set the Paper Type to Labels.

• Do not print a large number of labels continuously.

• Do not use labels that have coating or sizing applied to make the labels liquid‑resistant.

• Do not use labels that have exposed adhesive on the label sheets.

When printing on card stock:

• Feed card stock from Tray 1 only.

• We recommend using Springhill Index Plus 90 lb card stock.

• For the best print quality, always set the Paper Type to Card Stock.

Lexmark C520, C522, and C524

Limit label printing to occasional use of paper office labels designed for laser printers. The Lexmark C520, C522, and

C524 do not support vinyl or polyester labels.

The Lexmark C520, C522, and C524 support stocks up to 176 g/m

. Card stock is supported from Tray 1, Tray 2, the

manual feed slot, and the multipurpose feeder. Labels are supported only from the multipurpose feeder and the manual

feed slot.

Printer specifications 34

Tray 1 supports approximately 120 sheets of card stock and Tray 2 supports approximately 250 sheets of card stock.

The multipurpose feeder supports approximately 50 sheets of card stock or labels, and the manual feed slot accepts

single sheets only. The following table lists the maximum weights supported.

Paper source

Card stock Labels*

Index Bristol Tag Cover

Papergrain long grain short grain long grain short grain long grain short

Tray 1 (standard tray)

120 g/m

163 g/m

120 g/m

163 g/m

135 g/m

176 g/m

—

Tray 2 (optional tray)

120 g/m

163 g/m

120 g/m

163 g/m

135 g/m

176 g/m

—

Multipurpose feeder

Manual feed slot

120 g/m

163 g/m

120 g/m

163 g/m

135 g/m

176 g/m

135 g/m

* Vinyl labels are not supported.

Labels Width: 105–216 mm (4.1–8.5 in.)

Length: 220–297 mm (8.7–11.7 in.)

Weight:

120–163 g/m

(32–43 lb)

Thickness: 0.13–0.20 mm (0.005–0.008 in.)

Smoothness: 50–300 Sheffield*

* 50–150 Sheffield is optimal. This printer may support labels with smoothness of less than 50 Sheffield

such as coated paper, polyester, vinyl, or other synthetic facestock paper. Using media higher than 200

Sheffield could result in print quality degradation.

Card stock Weight:

Up to 163 g/m

Index Bristol (90 lb)

Up to 163 g/m

Tag (100 lb)

Cover stock Weight:

Up to 176 g/m

For more information on the supported media sizes, see the printer User's Guide on the publications CD.

Card stock and label guidelines

When printing on labels:

• Use only paper labels. Do not use vinyl labels.

• Use only label sheets that have no gaps between the labels.

Acceptable labels

Unacceptable labels

• Recommended labels are Avery 5260.

Printer specifications 35

• From the printer control panel or from MarkVision Professional, set Paper Type to Labels.

• Do not print a large number of labels continuously.

• Do not use labels that have coating or sizing applied to make the labels liquid‑resistant.

• Do not use labels that have exposed adhesive on the label sheets.

When printing on card stock:

• We recommend using Springhill Index Plus 90 lb card stock.

• For the best print quality, always set Paper Type to Card Stock.

For more information, see

“Pick roller technology” on page 11.

Lexmark C530, C532, and C534

Limit label printing to occasional use of paper office labels designed for laser printers. The Lexmark C530, C532, and

C534 do not support vinyl or polyester labels.

The Lexmark C530, C532, and C534 support stocks up to 176 g/m

. Card stock and labels are supported from Tray 1,

Tray 2, the manual feed slot, and the multipurpose feeder.

Tray 1 supports approximately 120 sheets of card stock, and Tray 2 supports approximately 250 sheets of card stock.

The multipurpose feeder supports approximately 50 sheets of card stock or labels and the manual feed slot accepts

single sheets only. The following table lists the maximum weights supported.

Paper source

Card stock Labels*

Index Bristol Tag Cover

Papergrain long grain short grain long grain short grain long grain short

Tray 1 (standard tray)

120 g/m

163 g/m

120 g/m

163 g/m

135 g/m

176 g/m

131 g/m

Tray 2 (optional tray)

120 g/m

163 g/m

120 g/m

163 g/m

135 g/m

176 g/m

131 g/m

Multipurpose feeder

Manual feeder

120 g/m

163 g/m

120 g/m

163 g/m

135 g/m

176 g/m

131 g/m

* Vinyl labels are not supported.

Printer specifications 36

Labels Width: 76.2–216 mm (3–8.5 in.)

Length: 123.8–355.6 mm (4.88–14 in.)

Weight:

131 g/m

(35 lb)

Thickness: 0.13–0.20 mm (0.005–0.008 in.)

Smoothness: 50–300 Sheffield*

* 50–150 Sheffield is optimal. This printer may support labels with smoothness of less than 50 Sheffield

such as coated paper, polyester, vinyl, or other synthetic facestock paper. Using media higher than 200

Sheffield could result in print quality degradation.

Card stock Weight:

Up to 163 g/m

Index Bristol (90 lb)

Up to 163 g/m

Tag (100 lb)

Cover stock Weight:

Up to 176 g/m

For more information on the supported media sizes, see the printer User's Guide on the publications CD.

Card stock and label guidelines

When printing on labels:

• Use only paper labels. Do not use vinyl labels.

• Use only label sheets that have no gaps between the labels.

Acceptable labels

Unacceptable labels

• We recommend using Avery 5260.

• From the printer control panel or from MarkVision Professional, set Paper Type to Labels.

• Do not print a large number of labels continuously.

• Do not use labels that have coating or sizing applied to make the labels liquid‑resistant.

• Do not use labels that have exposed adhesive on the label sheets.

When printing on card stock:

• We recommend using Springhill Index Plus 90 lb card stock.

• For the best print quality, always set Paper Type to Card Stock.

For more information, see

“Pick roller technology” on page 11.

Printer specifications 37

Lexmark C540, C543, C544, and C546dtn

Notes:

• Your printer may not have a 650‑sheet duo drawer with an integrated multipurpose feeder.

• The 250‑sheet tray (Tray 1) and the 650‑sheet duo drawer support the same paper sizes and types.

• Not all models are pictured.

Limit label printing to occasional use of paper office labels designed for laser printers. The Lexmark C540, C543, C544,

and C546dtn do not support vinyl or polyester labels.

The Lexmark C540, C543, C544, and C546dtn support card stock weights up to 176 g/m

. Card stock and labels are

supported from Tray 1, Tray 2, the manual feeder, and the multipurpose feeder.

Tray 1 supports approximately 100 sheets of card stock or labels, and Tray 2 supports approximately 200 sheets of card

stock or labels. The multipurpose feeder supports approximately 50 sheets of card stock or labels, and the manual

feeder accepts single sheets only. Capacity varies depending on label material and construction. The following table

lists the maximum weights supported.

Paper source Grain direction

Card stock Labels

Index Bristol Tag Cover Paper

Standard and optional

250‑sheet tray

grain long

grain short

120 g/m

163 g/m

120 g/m

163 g/m

135 g/m

176 g/m

131 g/m

Tray 2 (optional

tray/drawer)

grain long

grain short

120 g/m

163 g/m

120 g/m

163 g/m

135 g/m

176 g/m

131 g/m

Multipurpose and

manual feeder*

grain long

grain short

120 g/m

163 g/m

120 g/m

163 g/m

135 g/m

176 g/m

131 g/m

* The multipurpose feeder may not support labels with certain design characteristics.

Labels Width: 105–216 mm (4.1–8.5 in.)

Length: 148–356 mm (5.8–14 in.)

Weight:

131 g/m

(35 lb bond)

Thickness: 0.102–0.254 mm (0.004–0.010 in.)

Smoothness: 50–300 Sheffield*

Printer specifications 38

* 50–150 Sheffield is optimal. This printer may support labels with smoothness of less than 50 Sheffield, such as coated

paper, polyester, vinyl or other synthetic facestock paper. Using media higher than 200 Sheffield could result in print quality

degradation.

For more information on the supported media sizes, see the printer User's Guide on the publications CD.

Card stock and label guidelines

When printing on labels:

• Use only paper labels. Do not use vinyl labels.

• Use only label sheets that have no gaps between the labels.

Acceptable labels

Unacceptable labels

• For optimal printing, use Avery laser labels.

• From the printer control panel or from MarkVision Professional, set Paper Type to Labels.

• Do not print a large number of labels continuously.

• Do not use labels that have coating or sizing applied to make the labels liquid‑resistant.

• Do not use labels that have exposed adhesive on the label sheets.

When printing on card stock:

• For optimal printing, use a 90‑lb Index card stock.

• For the best print quality, always set Paper Type to Card Stock.

For more information, see

“Pick roller technology” on page 11.

Lexmark C720

Printer specifications 39

Limit label printing to occasional use of paper office labels designed for laser printers. The Lexmark C720 does not

support vinyl or polyester labels.

The Lexmark C720 supports stocks up to 43 lb (163 g/m

). Feed labels from the standard tray only, which holds up to

80 sheets of labels or up to 120 sheets of card stock.

The following table lists the maximum weights supported.

Paper source

Card stock Labels

Index Bristol Tag Cover Paper Vinyl

Tray 1 (standard tray)

163 g/m

—

163 g/m

—

For paper and transparency specifications, see the printer User's Guide.

Labels Width: 105–216 mm (4.1–8.5 in.)

Length: 220–297 mm (8.7–11.7 in.)

Weight:

120–163 g/m

(32–43 lb)

Thickness: 0.13–0.20 mm (0.005–0.008 in.)

Smoothness: 100–400 Sheffield*

* 150–250 Sheffield is optimal. Using media higher than 300 Sheffield could result in printing degradation.

Card stock Weight:

Up to 163 g/m

Index Bristol (90 lb)

Up to 163 g/m

Tag (100 lb)

Card stock and label guidelines

When printing on labels:

• Feed labels from Tray 1 only.

• Use only paper labels. Do not use vinyl labels.

• Use only label sheets that have no gaps between the labels.

Acceptable labels

Unacceptable labels

• Recommended labels are Avery 5260.

• From the operator panel or from MarkVision Professional, set the Paper Type to Labels.

• Do not print a large number of labels continuously.

• Do not use labels that have coating or sizing applied to make the labels liquid‑resistant.

• Do not use labels that have exposed adhesive on the label sheets.

Printer specifications 40

When printing on card stock:

• Feed card stock from Tray 1 only.

• We recommend using Springhill Index Plus 90 lb card stock.

• For the best print quality, always set the Paper Type to Card Stock.

Lexmark C734 and C736

Lexmark C734 and C736 support card stock and labels from the standard 550‑sheet tray, an optional 550‑sheet tray,

the multipurpose tray, and an optional 550‑sheet specialty media drawer.

Note: The optional 2,000‑sheet tray does not support card stock or labels.

Tray 1 supports approximately 120 sheets of card stock, and the optional 550‑sheet tray supports approximately

250 sheets of card stock. The multipurpose feeder supports approximately 50 sheets of card stock or labels. The

following tables list the maximum weights supported.

Paper source

Card stock

Index Bristol Tag Cover

grain long grain short grain long grain short grain long grain short

Standard 550‑sheet tray (Tray 1)

163 g/m

199 g/m

163 g/m

203 g/m

163 g/m

216 g/m

Optional 550‑sheet tray

Optional 550‑sheet specialty media drawer

163 g/m

199 g/m

163 g/m

203 g/m

163 g/m

216 g/m

Multipurpose tray

163 g/m

199 g/m

163 g/m

203 g/m

163 g/m

216 g/m

Paper source Labels

Dual Web/Paper Polyester Vinyl

Standard 550‑sheet tray (Tray 1)

180 g/m

220 g/m

300 g/m

Optional 550‑sheet tray

Optional 550‑sheet specialty media drawer

180 g/m

220 g/m

300 g/m

Multipurpose tray

180 g/m

220 g/m

300 g/m

Printer specifications 41

Labels Width: 76.2–216 mm (3–8.5 in.)

Length: 123.8–355.6 mm (4.88–14 in.)

Weight:

180–300 g/m

(48–92 lb)

Thickness: 0.13–0.20 mm (0.005–0.008 in.)

Smoothness: 50–300 Sheffield*

* 50–150 Sheffield is optimal. This printer may support labels with smoothness of less than 50 Sheffield

such as coated paper, polyester, vinyl, or other synthetic facestock paper. Using media higher than 200

Sheffield could result in print quality degradation.

Card stock Weight:

Up to 199 g/m

Index Bristol (110 lb)

Up to 203 g/m

Tag (125 lb)

Cover stock Weight:

Up to 216 g/m

(80 lb)

For more information on the supported media sizes, see the printer User's Guide on the publications CD.

Card stock and label guidelines

When printing on labels:

• Print samples on the labels being considered for use before buying large quantities.

• Use only label sheets that have no gaps between the labels.

Acceptable labels

Unacceptable labels

• From the printer control panel or from MarkVision Professional, set Paper Type to Labels.

• Do not print a large number of labels continuously.

• Do not use labels that have coating or sizing applied to make the labels liquid‑resistant.

• Do not use labels that have exposed adhesive on the label sheets.

When printing on card stock:

• Select the appropriate paper texture setting.

• For the best print quality, always set Paper Type to Card Stock.

• Use grain short card stock when possible.

• Do not use preprinted card stock manufactured with chemicals that may contaminate the printer.

• Be aware that preprinting, perforation, and creasing may significantly affect the print quality and cause jams or

other paper‑handling problems.

For more information, see

“Pick roller technology” on page 11.

Printer specifications 42

Lexmark C746 and C748

The Lexmark C746 and C748 printer models support card stock and labels from the standard 550‑sheet tray, an optional

550‑sheet tray, the multipurpose feeder, and the optional 550‑sheet specialty media tray.

Note: The optional 2,000‑sheet tray does not support card stock or labels.

Tray 1, the optional 550‑sheet tray, and the specialty media tray support approximately 250 sheets of card stock or

labels. The following table lists the maximum weights supported.

Paper source

Grain

direction

Card stock Labels

Index

Bristol

Tag Cover Paper

Dual‑web

paper

Polyester Vinyl

Standard and

optional

550‑sheet tray

grain long

grain short

199 g/m

163 g/m

203 g/m

176 g/m

216 g/m

180 g/m

220 g/m

300 g/m

Multipurpose

feeder

grain long

grain short

199 g/m

163 g/m

203 g/m

176 g/m

216 g/m

180 g/m

220 g/m

300 g/m

* The multipurpose feeder may not support labels with certain design characteristics.

Labels Width:

76–216 mm (3–8.5 in.)

Length:

124–356 mm (4.88–14 in.)

Weight:

Up to 180 g/m

Paper (48 lb)

Up to 180 g/m

Dual Web Paper (48 lb)

Up to 220 g/m

Polyester (59 lb)

Up to 300 g/m

Vinyl (92 lb)

Thickness: 0.13–0.20 mm (0.005–0.008 in.)

Smoothness:

50–300 Sheffield

Printer specifications 43

The minimum size for labels supported in the multipurpose feeder is 76 x 124 mm (3 x 4.88 in.). The

minimum size for labels supported in the standard and optional trays is 148 x 210 mm (5.82 x 8.26 in.)

50–150 Sheffield is optimal. This printer may support labels with smoothness of less than 50 Sheffield

such as coated paper, polyester, vinyl, or other synthetic facestock paper. Using media higher than

200 Sheffield could result in print quality degradation.

Card stock Weight:

Up to 199 g/m

Index Bristol (110 lb)

Up to 203 g/m

Tag (125 lb)

Up to 216 g/m

Cover (80 lb)

For more information on the supported media sizes, see the printer User's Guide on the Software and

Documentation CD.

Card stock and label guidelines

When printing on labels:

• Print samples on the labels being considered for use before buying large quantities.

• Use only label sheets that have no gaps between the labels.

Acceptable labels

Unacceptable labels

• From the printer control panel or from MarkVision Professional, set Paper Type to Labels.

• Do not print a large number of labels continuously.

• Do not use labels that have coating or sizing applied to make the labels liquid‑resistant.

• Do not use labels that have exposed adhesive on the label sheets.

• Run the labels only once through the printer as this may contaminate the printer.

When printing on card stock:

• Select the appropriate Paper Texture setting.

• For the best print quality, always set Paper Type to Card Stock.

• Use grain short card stock when possible.

• Do not use preprinted card stock manufactured with chemicals that may contaminate the printer.

• Be aware that preprinting, perforation, and creasing may significantly affect the print quality and cause jams or

other paper‑handling problems.

For more information, see

“Pick roller technology” on page 11.

Printer specifications 44

Lexmark C750

The Lexmark C750 prints on many labels designed for use with laser printers.

The following table lists the maximum weights supported by the trays and the multipurpose feeder.

The Lexmark C750 paper feeding mechanism uses advanced technology that enhances feeding reliability. The

Lexmark C750 trays, which hold approximately 500 sheets of 75 g/m

paper, reliably feed all supported media.

Note: The optional 2000‑sheet drawer supports paper only.

Print material

Range or maximum weight supported

500‑sheet tray and optional

500‑sheet drawer

Multipurpose feeder

Paper

(grain direction

)

Xerographic or business paper

60–176 g/m

(16–47 lb bond)

60–176 g/m

(16–47 lb bond)

Card Stock

(grain long

)

Index Bristol

163 g/m

(90 lb) 163 g/m

(90 lb)

Tag

163 g/m

(100 lb) 163 g/m

(100 lb)

Cover

176 g/m

(65 lb) 176 g/m

(65 lb)

Card Stock

(grain short

)

Index Bristol

199 g/m

(110 lb) 199 g/m

(110 lb)

Tag

203 g/m

(125 lb) 203 g/m

(125 lb)

Cover

216 g/m

(80 lb) 216 g/m

(80 lb)

Labels Paper

180 g/m

(48 lb bond) 199 g/m

(53 lb bond)

Dual‑web paper

180 g/m

(48 lb bond) 199 g/m

(53 lb bond)

Vinyl

300 g/m

(92 lb liner) 260 g/m

(78 lb liner)

Polyester

220 g/m

(59 lb bond) 220 g/m

(59 lb bond)

Paper less than 75 g/m

is supported only when the relative humidity is less than 60% and is not supported in duplex.

See “Grain orientation” on page 17 for specific recommendations.

Vinyl labels are supported only when printing environment and media are 20–32°C (68–90°F).

Pressure‑sensitive area must enter the printer first.

Printer specifications 45

Print material

Range or maximum weight supported

500‑sheet tray and optional

500‑sheet drawer

Multipurpose feeder

Integrated forms

Pressure‑sensitive area

140–175 g/m

Paper base (grain long)

75–135 g/m

(20–36 lb bond)

75–135 g/m

(20–36 lb bond)

Paper less than 75 g/m

is supported only when the relative humidity is less than 60% and is not supported in duplex.

See “Grain orientation” on page 17 for specific recommendations.

Vinyl labels are supported only when printing environment and media are 20–32°C (68–90°F).

Pressure‑sensitive area must enter the printer first.

For paper and transparency specifications, see the Lexmark C750 Publications CD.

The following table indicates the paper sizes each tray supports.

Source

Standard sizes

(width x length)

Universal sizes

(width x length)

Minimum Maximum Minimum Maximum

Standard tray

500‑sheet drawer

148 x 210 mm

(5.83 x 8.27 in.)

215.9 x 355.6 mm

(8.5 x 14 in.)

139.7 x 210 mm

(5.5 x 8.27 in.)

215.9 x 355.6 mm

(8.5 in. x 14 in.)

Multipurpose

feeder*

148 x 210 mm

(5.83 x 8.27 in.)

215.9 x 355.6 mm

(8.5 x 14 in.)

69.85 x 127 mm

(2.75 in. x 5 in.)

229 x 355.6 mm

(9.01 x 14 in.)

* If you load paper that is narrower than 148 mm (5.83 in.) in the multipurpose feeder (for example, 3 x 5‑inch index cards),

set the MP Feeder Size menu item to Universal.

Labels Thickness: 0.102–0.305 mm (0.004–0.012 in.)

Smoothness: 100–400* Sheffield

* 150–250 Sheffield is optimal. Using media higher than 300 Sheffield could result in printing degradation.

Card stock and label guidelines

Labels are one of the most difficult print materials for laser printers. A fuser equipped with a web oiler may be required

for label applications to optimize feed reliability. Contact your local service representative for ordering information.

If you print large quantities of labels or other glossy print media, replace the fuser housing with a web oiler field upgrade

kit (P/N 12G6307 for a 115 V printer, P/N 12G6308 for a 220 V printer).

When printing on labels:

• Using the printer operator panel, set the Paper Type to Labels in the Paper Menu. For vinyl and other heavy labels,

set the Labels Weight (under the Paper Weight menu) to Heavy, and set the Labels Texture (under the Paper Texture

menu) to Smooth.

• Do not load labels together with paper or transparencies in the same paper tray. Combining print materials can

cause feeding problems.

• Use full label sheets. Partial sheets may cause labels to peel off during printing, resulting in a paper jam. Adhesive

material may contaminate your printer. It could also void your printer and cartridge warranties.

When feeding labels, the number of labels per sheet can affect registration more than basis weight. Typically, the more

labels per sheet, the better the registration.

Printer specifications 46

When printing on card stock:

• Set the Paper Type to Card Stock in the Paper Menu.

• Do not use card stock that is creased. It may cause paper jams.

For more information, see the following:

• “Pick roller technology” on page 11

• “Grain orientation” on page 17

• “Maintenance procedures” on page 14

• “Troubleshooting” on page 14

Lexmark C752

The Lexmark C752 prints on many labels designed for use with laser printers.

The Lexmark C752 trays, which hold approximately 500 sheets of 75 g/m

paper, reliably feed all supported media.

The following table lists the maximum weights supported by the trays and the multipurpose feeder.

Note: The optional 2000‑sheet drawer supports paper only

Print material

Range or maximum weight supported

500‑sheet tray and optional

500‑sheet drawer

Multipurpose feeder

Paper

(grain direction

)

Xerographic or business paper

60–176 g/m

(16–47 lb bond)

60–176 g/m

(16–47 lb bond)

Card stock

(grain long

)

Index Bristol

163 g/m

(90 lb) 163 g/m

(90 lb)

Tag

163 g/m

(100 lb) 163 g/m

(100 lb)

Cover

176 g/m

(65 lb) 176 g/m

(65 lb)

Paper less than 75 g/m

is supported only when the relative humidity is less than 60% and is not supported in duplex.

See “Grain orientation” on page 17 for specific recommendations.

Vinyl labels are supported only when printing environment and media are 20–32°C (68–90°F).

Pressure‑sensitive area must enter the printer first.

Printer specifications 47

Print material

Range or maximum weight supported

500‑sheet tray and optional

500‑sheet drawer

Multipurpose feeder

Card stock

(grain short

)

Index Bristol

199 g/m

(110 lb) 199 g/m

(110 lb)

Tag

203 g/m

(125 lb) 203 g/m

(125 lb)

Cover

216 g/m

(80 lb) 216 g/m

(80 lb)

Labels Paper

180 g/m

(48 lb bond) 199 g/m

(53 lb bond)

Dual‑web paper

180 g/m

(48 lb bond) 199 g/m

(53 lb bond)

Vinyl

300 g/m

(92 lb liner) 260 g/m

(78 lb liner)

Polyester

220 g/m

(59 lb bond) 220 g/m

(59 lb bond)

Integrated forms

Pressure‑sensitive area

140–175 g/m

Paper base (grain long)

75–135 g/m

(20–36 lb bond)

75–135 g/m

(20–36 lb bond)

Paper less than 75 g/m

is supported only when the relative humidity is less than 60% and is not supported in duplex.

See “Grain orientation” on page 17 for specific recommendations.

Vinyl labels are supported only when printing environment and media are 20–32°C (68–90°F).

Pressure‑sensitive area must enter the printer first.

For paper and transparency specifications, see the Lexmark C752 Publications CD.

The following table indicates the paper sizes each tray supports.

Source

Standard sizes

(width x length)

Universal sizes

(width x length)

Minimum Maximum Minimum Maximum

Standard tray

500‑sheet drawer

148 x 210 mm

(5.83 x 8.27 in.)

215.9 x 355.6 mm

(8.5 x 14 in.)

139.7 x 210 mm

(5.5 x 8.27 in.)

215.9 x 355.6 mm

(8.5 in. x 14 in.)

Multipurpose

feeder*

148 x 210 mm

(5.83 x 8.27 in.)

215.9 x 355.6 mm

(8.5 x 14 in.)

69.85 x 127 mm

(2.75 in. x 5 in.)

229 x 355.6 mm

(9.01 x 14 in.)

* If you load paper that is narrower than 148 mm (5.83 in.) in the multipurpose feeder (for example, 3 x 5‑inch index cards),

set the MP Feeder Size menu item to Universal.

Labels Thickness: 0.102–0.305 mm (0.004–0.012 in.)

Smoothness: 100–400* Sheffield

* 150–250 Sheffield is optimal. Using media higher than 300 Sheffield could result in printing degradation.

Card stock and label guidelines

Labels are one of the most difficult print materials for laser printers. A fuser equipped with a web oiler may be required

for label applications to optimize feed reliability. Contact your local service representative for ordering information.

If you print large quantities of labels or other glossy print media, replace the fuser housing with a web oiler (P/N 56P1555

for a 115 V printer or P/N 56P1556 for a 220 V printer).

Printer specifications 48

When printing on labels:

• Using the printer operator panel, set the Paper Type to Labels in the Paper Menu. For vinyl and other heavy labels,

set the Labels Weight (under the Paper Weight menu) to Heavy, and set the Labels Texture (under the Paper Texture

menu) to Smooth.

• Do not load labels together with paper or transparencies in the same paper tray. Combining print materials can

cause feeding problems.

• Use full label sheets. Partial sheets may cause labels to peel off during printing, resulting in a paper jam. Adhesive

material may contaminate your printer. It could also void your printer and cartridge warranties.

When feeding labels, the number of labels per sheet can affect registration more than basis weight. Typically, the more

labels per sheet, the better the registration.

When printing on card stock:

• Set the Paper Type to Card Stock in the Paper Menu.

• Do not use card stock that is creased. It may cause paper jams.

For more information, see the following:

• “Pick roller technology” on page 11

• “Grain orientation” on page 17

• “Maintenance procedures” on page 14

• “Troubleshooting” on page 14

Lexmark C760 and C762

Lexmark C760 and C762 print on many labels designed for use with laser printers.

The following table lists the maximum weights supported by the trays and the multipurpose feeder.

Note: The optional 2,000‑sheet drawer supports paper only.

Printer specifications 49

Print material

Range or maximum weight supported

500‑sheet tray and optional

500‑sheet drawer

Multipurpose feeder

Paper

(grain direction

)

Xerographic or business

paper

60–176 g/m

(16–47 lb bond)

60–176 g/m

(16–47 lb bond)

Card stock

(grain long

)

Index Bristol

163 g/m

(90 lb) 163 g/m

(90 lb)

Tag

163 g/m

(100 lb) 163 g/m

(100 lb)

Cover

176 g/m

(65 lb) 176 g/m

(65 lb)

Card stock

(grain short

)

Index Bristol

199 g/m

(110 lb) 199 g/m

(110 lb)

Tag

203 g/m

(125 lb) 203 g/m

(125 lb)

Cover

216 g/m

(80 lb) 216 g/m

(80 lb)

Labels Paper

180 g/m

(48 lb bond) 199 g/m

(53 lb bond)

Dual‑web paper

180 g/m

(48 lb bond) 199 g/m

(53 lb bond)

Vinyl

300 g/m

(92 lb liner) 260 g/m

(78 lb liner)

Polyester

220 g/m

(59 lb bond) 220 g/m

(59 lb bond)

Integrated forms

Pressure‑sensitive area

140–175 g/m

Paper base (grain long)

75–135 g/m

(20–36 lb bond)

75–135 g/m

(20–36 lb bond)

Paper less than 75 g/m

is supported only when the relative humidity is less than 60% and is not supported in duplex.

See “Grain orientation” on page 17 for specific recommendations.

Vinyl labels are supported only when printing environment and media are 20–32°C (68–90°F).

Pressure‑sensitive area must enter the printer first.

For paper and transparency specifications, see the printer publications CD.

The following table indicates the paper sizes each tray supports.

Labels Thickness: 0.102–0.305 mm (0.004–0.012 in.)

Smoothness: 50–300 Sheffield*

* 50–150 Sheffield is optimal. This printer may support labels with smoothness of less than 50 Sheffield such as coated paper,

polyester, vinyl, or other synthetic facestock papers.Using media higher than 200 Sheffield could result in printing

degradation.

Card stock and label guidelines

Labels are one of the most difficult print materials for laser printers. A fuser equipped with a web oiler may be required

for label applications to optimize feed reliability. Contact your local service representative for ordering information.

If you print large quantities of labels or other glossy print media, replace the fuser housing with a web oiler (P/N 56P1555

for a 115 V printer or P/N 56P1556 for a 220 V printer).

Printer specifications 50

When printing on labels:

• Using the printer operator panel, set Paper Type to Labels in the Paper Menu. For vinyl and other heavy labels, set

Labels Weight (under the Paper Weight menu) to Heavy, and set Labels Texture (under the Paper Texture menu)

to Smooth.

• Do not load labels together with paper or transparencies in the same paper tray. Combining print materials can

cause feeding problems.

• Use full label sheets. Partial sheets may cause labels to peel off during printing, resulting in a paper jam. Adhesive

material may contaminate your printer. It could also void your printer and cartridge warranties.

Print on sheets with more number of labels to improve registration.

When printing on card stock:

• Set Paper Type to Card Stock in the Paper Menu.

• Do not use creased card stock. It may cause paper jams.

For more information, see the following:

• “Pick roller technology” on page 11

• “Grain orientation” on page 17

• “Maintenance procedures” on page 14

• “Troubleshooting” on page 14

Lexmark C770, C772, C780, and C782

The Lexmark C770, C772, C780, and C782 print on many labels designed for use with laser printers.

The following tables list the maximum weights supported by the trays and the multipurpose feeder.

Note: The optional 2000‑sheet drawer supports plain and glossy paper.

Paper source

Card stock

(grain long/grain short)

Index Bristol Tag Cover

grain long grain short grain long grain short grain long grain short

500‑sheet drawers

163 g/m

199 g/m

163 g/m

203 g/m

176 g/m

216 g/m

Multipurpose feeder

163 g/m

199 g/m

163 g/m

203 g/m

176 g/m

216 g/m

Printer specifications 51

Paper source

Labels

Paper Dual‑web paper Polyester Vinyl

1, 2

500‑sheet drawers

180 g/m

220 g/m

300 g/m

Multipurpose feeder

199 g/m

220 g/m

260 g/m

Vinyl labels are supported only when the printing environment and media are 20–32.2°C (68–90°F).

The skew performance of heavy vinyl labels may be enhanced by feeding from an optional 500‑sheet drawer if placement

of the image is critical.

For paper and transparency specifications, see the printer publications CD.

Labels Thickness: 0.102–0.305 mm (0.004–0.012 in.)

Smoothness: 50–300 Sheffield*

* 50–150 Sheffield is optimal. This printer may support labels with smoothness of less than 50 Sheffield such as coated paper,

polyester, vinyl, or other synthetic facestock paper. Using media higher than 200 Sheffield could result in print quality

degradation.

Card stock and label guidelines

Labels are one of the most difficult print materials for laser printers. A fuser equipped with a dry web cleaner may be

required for label applications to optimize feed reliability. If you print large quantities of labels or other glossy print

media, then install a dry web cleaner upgrade kit (P/N 40X1856). Contact your local service representative for ordering

information.

When printing on labels:

• From the printer control panel, set Paper Type to Labels in the Paper Menu. For vinyl and other heavy labels, set

Labels Weight (under the Paper Weight menu) to Heavy, and set Labels Texture (under the Paper Texture menu)

to Smooth.

• Do not load labels together with paper or transparencies in the same paper tray. Combining print materials can

cause feeding problems.

• Use full label sheets. Partial sheets may cause labels to peel off during printing, resulting in a paper jam. Adhesive

material may contaminate your printer. It could also void your printer and cartridge warranties.

Print on sheets with more number of labels to improve registration.

When printing on card stock:

• Set Paper Type to Card Stock in the Paper Menu.

• Do not use creased card stock. It may cause paper jams.

For more information, see the following:

• “Pick roller technology” on page 11

• “Maintenance procedures” on page 14

• “Troubleshooting” on page 14

Printer specifications 52

Lexmark C792e, C792de, C792dte, and C792dhe

The Lexmark C792e, C792de, C792dte, and C792dhe printer models print on many labels designed for use with laser

printers.

The following tables list the maximum weights supported by the trays and the multipurpose feeder.

Overview of card stock support

Paper source

Card stock

(grain long/grain short)

Index Bristol Tag Cover

grain long grain short grain long grain short grain long grain short

Standard and optional

550‑sheet trays

163 g/m

199 g/m

163 g/m

203 g/m

176 g/m

216 g/m

Multipurpose feeder

163 g/m

199 g/m

163 g/m

203 g/m

176 g/m

216 g/m

Overview of label support

Paper source

Labels

Paper Dual‑web paper Polyester Vinyl

1, 2

Standard and optional 550‑sheet trays

180 g/m

220 g/m

300 g/m

Multipurpose feeder

199 g/m

220 g/m

260 g/m

Vinyl labels are supported only when the printing environment and media are 20–32.2°C (68–90°F).

The skew performance of heavy vinyl labels may be enhanced by feeding from an optional 500‑sheet drawer if placement

of the image is critical.

For paper and transparency specifications, see the printer publications CD.

Media specifications

Labels Thickness: 0.102–0.305 mm (0.004–0.012 in.)

Smoothness: 50–300* Sheffield

Printer specifications 53

* 50–150 Sheffield is optimal. This printer may support labels with smoothness of less than 50 Sheffield such as coated paper,

polyester, vinyl, or other synthetic facestock paper. Using media higher than 200 Sheffield could result in print quality

degradation.

Card stock and label guidelines

Labels are one of the most difficult print materials for laser printers. A fuser equipped with a dry web cleaner may be

required for label applications to optimize feed reliability. If you print large quantities of labels or other glossy print

media, then install a dry web cleaner upgrade kit (P/N 40X1856). Contact your local service representative for ordering

information.

When printing on labels:

• From the printer control panel, set Paper Type to Labels in the Paper Menu. For vinyl and other heavy labels, set

Labels Weight (under the Paper Weight menu) to Heavy, and set Labels Texture (under the Paper Texture menu)

to Smooth.

• Do not load labels together with paper or transparencies in the same paper tray. Combining print materials can

cause feeding problems.

• Use full label sheets. Partial sheets may cause labels to peel off during printing, resulting in a paper jam. Adhesive

material may contaminate your printer. It could also void your printer and cartridge warranties.

Print on sheets with more number of labels to improve registration.

When printing on card stock:

• Set Paper Type to Card Stock in the Paper Menu.

• Do not use creased card stock. It may cause paper jams.

For more information, see the following:

• “Pick roller technology” on page 11

• “Maintenance procedures” on page 14

• “Troubleshooting” on page 14

Lexmark C910

Limit label printing to occasional use of paper office labels designed for laser printers. We do not recommend using

vinyl or polyester labels.

The Lexmark C910 supports stocks up to 163 g/m

(90 lb).

The following table lists the maximum weights supported by the heavy media tray and the multipurpose feeder.

Printer specifications 54

Paper source

Card stock Labels

Index Bristol Tag Cover Paper Vinyl

Heavy media tray — — —

180 g/m

—

Multipurpose feeder

163 g/m

—

180 g/m

—

For paper and transparency specifications, see the Lexmark C910 Publications CD.

Labels Width: 210–216 mm (8.3–8.5 in.)

Length: 279–297 mm (11–11.7 in.)

Weight:

120–180 g/m

(32– 43 lb)

Thickness: 0.13–0.20 mm (0.005–0.008 in.)

Smoothness: 100–400 Sheffield*

* 150–250 Sheffield is optimal. Using media higher than 300 Sheffield could result in printing degradation.

Card stock Weight:

Up to 163 g/m

Index Bristol (90 lb)

Up to 163 g/m

Tag (100 lb)

Card stock and label guidelines

When printing on labels:

• Use only label sheets that have no gaps between the labels.

Acceptable labels

Unacceptable labels

• From the operator panel or from MarkVision Professional, set the Paper Type to Labels in the Paper Menu.

• Do not print a large number of labels continuously.

• Do not use labels that have coating or sizing applied to make the labels liquid‑resistant.

• Do not use labels that have exposed adhesive on the label sheets.

• We recommend using Avery paper labels.

When printing on card stock:

• We recommend using Springhill Index Plus 90 lb card stock.

• For the best print quality, always set the Paper Type to Card Stock in the Paper Menu.

Printer specifications 55

Lexmark C912

Limit label printing to occasional use of paper office labels designed for laser printers. We do not recommend using

vinyl or polyester labels.

The Lexmark C912 supports stocks up to 216 g/m

The following table lists the maximum weights supported by the standard tray and the multipurpose feeder.

Paper source

Card stock Labels

Index Bristol Paper Vinyl

Standard tray —

180 g/m

—

Multipurpose feeder

216 g/m

180 g/m

300 g/m

Labels Width: 210–216 mm (8.3–8.5 in.)

Length: 279–297 mm (11–11.7 in.)

Weight:

180 g/m

Thickness: 0.13–0.20 mm (0.005–0.008 in.)

Smoothness: 100–400 Sheffield*

* 150–250 Sheffield is optimal. Using media higher than 300 Sheffield could result in printing degradation.

Card stock Weight:

Up to 216 g/m

For paper and transparency specifications, refer to the printer publications CD.

Printer specifications 56

Card stock and label guidelines

When printing on labels:

• Use only label sheets that have no gaps between the labels.

Acceptable labels

Unacceptable labels

• From the operator panel or from MarkVision Professional, set the Paper Type to Labels in the Paper Menu.

• Do not print a large number of labels continuously.

• Do not use labels that have coating or sizing applied to make the labels liquid‑resistant.

• Do not use labels that have exposed adhesive on the label sheets.

• We recommend using Avery paper labels.

When printing on vinyl labels:

• From the operator panel or from MarkVision Professional, set the Paper Type to Card Stock in the Paper Menu. Set

the CardStock Weight (under the Paper Weight menu) to Heavy.

• Download the vinyl file, vinyl8ppm.npa, from our FTP site and send it to the printer (copy the file to the printer

port).

When printing on card stock:

• We recommend using Springhill Index Plus 90 lb card stock.

• For the best print quality, always set the Paper Type to Card Stock in the Paper Menu.

Lexmark C920

Limit label printing to occasional use of paper office labels designed for laser printers. We do not recommend using

vinyl or polyester labels.

Printer specifications 57

The Lexmark C920 supports stocks up to 216 g/m

The following table lists the maximum weights supported by the standard tray and the multipurpose feeder.

Paper source

Card stock Labels

Index Bristol Paper Vinyl

Standard tray —

180 g/m

—

Multipurpose feeder

216 g/m

180 g/m

300 g/m

Labels Width: 210–216 mm (8.3–8.5 in.)

Length: 279–297 mm (11–11.7 in.)

Weight:

180 g/m

Thickness: 0.13–0.20 mm (0.005–0.008 in.)

Smoothness: 100–400 Sheffield*

* 150–250 Sheffield is optimal. Using media higher than 300 Sheffield could result in printing degradation.

Card stock Weight:

Up to 216 g/m

Card stock and label guidelines

When printing on labels:

• Use only label sheets that have no gaps between the labels.

Acceptable labels

Unacceptable labels

• Set the Paper Type to Labels in the Paper Menu.

• Do not print a large number of labels continuously.

• Do not use labels that have coating or sizing applied to make the labels liquid‑resistant.

• Do not use labels that have exposed adhesive on the label sheets.

• We recommend using Avery paper labels.

When printing on card stock:

• We recommend using Springhill Index Plus 90 lb card stock.

• For the best print quality, always set the Paper Type to Card Stock in the Paper Menu.

Printer specifications 58

Lexmark C925

Limit label printing to occasional use of A4‑ or letter‑size paper office labels designed for laser printers. We do not

recommend using vinyl or polyester labels.

The trays and the multipurpose feeder support card stock. The multipurpose feeder supports card stocks up to 256 g/m

Always feed labels from the standard 150‑sheet tray or the multipurpose feeder.

The standard 250‑ and optional 550‑sheet trays do not support labels.

The following table lists the maximum weights supported by the trays and the multipurpose feeder.

Paper source

Card stock

(grain long/grain short)

Index Bristol Tag Cover

grain long grain short grain long grain short grain long grain short

Standard 150‑sheet

tray

120 g/m

163 g/m

120 g/m

163 g/m

135 g/m

176 g/m

Standard 250‑ and

optional 550‑sheet

trays

120 g/m

157 g/m

120 g/m

157 g/m

135 g/m

157 g/m

Multipurpose feeder

120 g/m

256 g/m

120 g/m

256 g/m

135 g/m

256 g/m

Paper source

Labels

Paper Vinyl

Standard 150‑sheet tray

131 g/m

Not applicable

Multipurpose feeder

131 g/m

Occasional use up to

256 g/m

Labels Width: 210–216 mm (8.3–8.5 in.)

Length: 279–356 mm (11–11.7 in.)

Weight:

120–128 g/m

Thickness: 0.13–0.20 mm (0.005–0.008 in.)

Smoothness: 100–400 Sheffield*

* 150–250 Sheffield is optimal. Using media higher than 300 Sheffield could result in print quality

degradation.

Printer specifications 59

Card stock Width: 210–216 mm (8.3–8.5 in.)

Length: 279–356 mm (11–11.7 in.)

Weight:

Up to 216 g/m

Card stock and label guidelines

When printing on labels:

• From the printer control panel, set Paper Type to Labels in the Paper Menu.

• Do not use label sheets with a slick backing material.

• Do not print within 1 mm (0.04 in.) of the die‑cut, the edge of the label or the perforations, or between the die‑cuts.

• Use full label sheets. Partial sheets may cause labels to peel off during printing, resulting in a paper jam.

• Do not use label sheets that have adhesive to the edge of the sheet. We recommend zone coating of the adhesive

at least 1 mm (0.04 in.) away from the edges. Adhesive material may contaminate your printer and could void your

warranty.

When printing on card stock:

• From the printer control panel, set Paper Type to Card Stock.

• Do not use creased card stock. It may cause paper jams.

• We recommend the use of grain long card stock.

Lexmark C935

Limit label printing to occasional use of A4‑ or letter‑size paper office labels designed for laser printers. We do not

recommend using vinyl or polyester labels.

Lexmark C935 supports card stock up to 220 g/m

The following table lists the maximum weights supported by the trays and the multipurpose feeder.

Tray 1 Trays 2 and 3 Multipurpose feeder

Labels Not applicable Not applicable

220 g/m

Card stock

105 g/m

220 g/m

Printer specifications 60

Labels Width: 210–216 mm (8.3–8.5 in.)

Length: 279–356 mm (11–11.7 in.)

Weight:

120–128 g/m

Thickness: 0.13–0.20 mm (0.005–0.008 in.)

Smoothness: 100–400 Sheffield*

* 150–250 Sheffield is optimal. Using media higher than 300 Sheffield could result in print quality

degradation.

Card stock Width: 210–216 mm (8.3–8.5 in.)

Length: 279–356 mm (11–11.7 in.)

Weight:

Up to 220 g/m

Card stock and label guidelines

When printing on labels:

• Load labels only on the multipurpose feeder.

• From the printer control panel, set Paper Type to Labels in the Paper Menu.

• Do not use label sheets with a slick backing material.

• Do not print within 1 mm (0.04 in.) of the die‑cut, the edge of the label or the perforations, or between the die‑cuts.

• Use full label sheets. Partial sheets may cause labels to peel off during printing, resulting in a paper jam.

• Do not use label sheets that have adhesive to the edge of the sheet. We recommend zone coating of the adhesive

at least 1 mm (0.04 in.) away from the edges. Adhesive material may contaminate your printer and could void your

warranty.

When printing on card stock:

• From the printer control panel, set Paper Type to Card Stock.

• Do not use creased card stock. It may cause paper jams.

• We recommend the use of grain long card stock.

Printer specifications 61

Lexmark C950

Limit label printing to occasional use of A4‑ or letter‑size paper office labels designed for laser printers. We do not

recommend using vinyl or polyester labels.

Lexmark C950 supports card stock up to 300 g/m

The following table lists the maximum weights supported by the trays and the multipurpose feeder.

Trays 1–4 Multipurpose feeder High‑capacity feeder

Labels

60–256 g/m

60–300 g/m

60–216 g/m

Card stock

60–256 g/m

60–300 g/m

60–216 g/m

Labels Width: 140–320 mm (5.5–12.6 in.)

Length: 182–457 mm (7.2–18 in.)

Weight:

60–256 g/m

Smoothness: 100–200 Sheffield

Card stock Width: 140–320 mm (5.5–12.6 in.)

Length: 182–457 mm (7.2–18 in.)

Weight:

60–256 g/m

Card stock and label guidelines

When printing on labels:

• From the printer control panel, set the paper size, type, texture, and weight in the Paper menu to match the labels

loaded in the tray.

• Do not use label sheets with a slick backing material.

• Do not print within 1 mm (0.04 in.) of the die‑cut, the edge of the label or the perforations, or between the die‑cuts.

• Use full label sheets. Partial sheets may cause labels to peel off during printing, resulting in a jam. Partial sheets

also contaminate the printer and the cartridge with adhesive, and could void the printer and toner cartridge

warranties.

Printer specifications 62

When printing on card stock:

• From the printer control panel, set the paper size, type, texture, and weight in the Paper menu to match the card

stock loaded in the tray.

• Do not use creased card stock. It may cause paper jams.

• We recommend the use of grain long card stock.

Lexmark CS310n, CS310dn, CS410n, CS410dn, and CS510de

Notes:

• Your printer may not have a 650‑sheet duo tray with an integrated multipurpose feeder.

• The 250‑sheet tray (Tray 1), 550‑sheet tray, and the 650‑sheet duo tray support the same paper sizes and types.

Limit label printing to occasional use of paper office labels designed for laser printers. The Lexmark CS310n, CS310dn,

CS410n, CS410dn, and CS510de printer models do not support vinyl or polyester labels.

The Lexmark CS310n, CS310dn, CS410n, CS410dn, and CS510de printer models support card stock weights up to

176 g/m

. Card stock and labels are supported from the 250‑sheet tray, 550‑sheet tray, 650‑sheet duo tray, the manual

feeder, and the multipurpose feeder.

The 250‑sheet tray supports approximately 100 sheets of card stock or labels, and the optional 550‑sheet tray supports

approximately 200 sheets of card stock or labels. The multipurpose feeder supports approximately 50 sheets of card

stock or labels, and the manual feeder accepts single sheets only. Capacity varies depending on label material and

construction.

The following table lists the maximum weights supported.

Paper source Grain direction

Card stock Labels

Index Bristol Tag Cover Paper

Standard 250‑sheet tray grain long

grain short

120 g/m

163 g/m

120 g/m

163 g/m

135 g/m

176 g/m

131 g/m

Standard or optional

550‑sheet tray

grain long

grain short

120 g/m

163 g/m

120 g/m

163 g/m

135 g/m

176 g/m

131 g/m

Multipurpose and

manual feeder*

grain long

grain short

120 g/m

163 g/m

120 g/m

163 g/m

135 g/m

176 g/m

131 g/m

* The multipurpose feeder may not support labels with certain design characteristics.

Printer specifications 63

Labels Width: 76.2–215.9 mm (3–8.5 in.)

Length: 127–355.6 mm (5–14 in.)

Weight:

131 g/m

(35 lb bond)

Thickness: 0.102–0.254 mm (0.004–0.010 in.)

Smoothness: 50–300 Sheffield*

* 50–150 Sheffield is optimal. This printer may support labels with smoothness of less than 50 Sheffield such as coated paper,

polyester, vinyl, or other synthetic facestock paper. Using media higher than 200 Sheffield could result in print quality

degradation.

Card stock Weight:

Up to 163 g/m

Index Bristol (90 lb)

Up to 163 g/m

Tag (100 lb)

Up to 176 g/m

Cover (65 lb)

For more information on the supported media sizes, see the printer User's Guide on the Software and

Documentation CD.

Card stock and label guidelines

When printing on labels:

• Use only paper labels. Do not use vinyl labels.

• Use only label sheets that have no gaps between the labels.

Acceptable labels

Unacceptable labels

• For optimal printing, use Avery laser labels.

• From the printer control panel or from MarkVision Professional, set Paper Type to Labels.

• Do not print a large number of labels continuously.

• Do not use labels that have coating or sizing applied to make the labels liquid‑resistant.

• Do not use labels that have exposed adhesive on the label sheets.

When printing on card stock:

• For optimal printing, use a 90‑lb Index card stock.

• For the best print quality, always set Paper Type to Card Stock.

• Set Card Stock Weight to Normal or Heavy.

• Do not use creased card stock. It may cause paper jams.

For more information, see

“Pick roller technology” on page 11.

Printer specifications 64

Lexmark CX310n, CX310dn, CX410e, CX410de, CX410dte,

CX510de, CX510dhe, and CX510dthe

Notes:

• Your printer may not have a 650‑sheet duo tray with an integrated multipurpose feeder.

• The 250‑sheet tray (Tray 1), 550‑sheet tray, and the 650‑sheet duo tray support the same paper sizes and types.

• The automatic document feeder (ADF) does not support card stock or labels.

Limit label printing to occasional use of paper office labels designed for use with laser printers. The Lexmark CX310n,

CX310dn, CX410e, CX410de, CX410dte, CX510de, CX510dhe, and CX510dthe printer models do not support vinyl or

polyester labels.

The following table lists the maximum weights supported by the trays and the multipurpose feeder.

Paper source Grain direction

Card stock Labels

Index Bristol Tag Cover Paper

Standard 250‑sheet

tray

grain long

grain short

120 g/m

163 g/m

120 g/m

163 g/m

135 g/m

176 g/m

131 g/m

Standard or optional

550‑sheet tray

grain long

grain short

120 g/m

163 g/m

120 g/m

163 g/m

135 g/m

176 g/m

131 g/m

Multipurpose feeder*

and manual feeder

grain long

grain short

120 g/m

163 g/m

120 g/m

163 g/m

135 g/m

176 g/m

131 g/m

* The multipurpose feeder may not support labels with certain design characteristics.

Labels Width: 76.2–215.9 mm (3–8.5 in.)

Length: 127–355.6 mm (5–14 in.)

Weight:

131 g/m

(35 lb bond)

Thickness: 0.102–0.254 mm (0.004–0.010 in.)

Smoothness: 50–300 Sheffield*

* 50–150 Sheffield is optimal. This printer may support labels with smoothness of less than 50 Sheffield such as coated paper,

polyester, vinyl, or other synthetic facestock paper. Using media higher than 200 Sheffield could result in print quality

degradation.

Printer specifications 65

Card stock Weight:

Up to 163 g/m

Index Bristol (90 lb)

Up to 163 g/m

Tag (100 lb)

Up to 176 g/m

Cover (65 lb)

Card stock and label guidelines

When printing on labels:

• Use only paper labels. Do not use vinyl labels.

• Use only label sheets that have no gaps between the labels.

Acceptable labels

Unacceptable labels

• From the printer control panel, set Paper Type to Labels in the Paper Menu.

• Do not load labels together with paper or transparencies in the same paper tray. Combining print materials can

cause feeding problems.

• Use only letter-, A4-, or legal-size full label sheets. Partial sheets may cause labels to peel off during printing, resulting

in a paper jam. Adhesive material may contaminate your printer. It could also void your printer and cartridge

warranties.

When printing on card stock:

• From the printer control panel, set Paper Type to Card Stock in the Paper Menu.

• Set Card Stock Weight to Normal or Heavy.

• Do not use creased card stock. It may cause paper jams.

Lexmark E120

Printer specifications 66

Limit label printing to occasional use of paper office labels designed for laser printers. We do not recommend using

vinyl or polyester labels.

The Lexmark E120 supports stocks up to 163 g/m

(43 lb). The automatic paper feeder can hold up to 10 sheets of card

stock or labels.

The following table lists the maximum weights supported by Tray 1 and the manual sheet feeder.

Paper source

Card stock Labels

Index Bristol Paper Vinyl

Tray 1

135–163 g/m

(up to 90 lb) 60–163 g/m

(16–43 lb)

—

Manual feed

135–163 g/m

(up to 90 lb) 60–163 g/m

(16–43 lb)

—

For paper and transparency specifications, see the Lexmark E220 Publications CD.

Labels Width: 210–216 mm (8.3–8.5 in.)

Length: 279–297 mm (11–11.7 in.)

Weight:

Up to 163 g/m

(43 lb)

Thickness: Up to 0.25 mm (0.01 in.)

Smoothness: 100–400* Sheffield

* 150–250 Sheffield is optimal. Using media higher than 300 Sheffield could result in printing degradation.

Card stock Weight:

Up to 163 g/m

Index Bristol (90 lb)

Up to 163 g/m

Tag (100 lb)

Note: To minimize curl, use the top exit when printing on card stock and labels.

For more information, see “Maintenance procedures” on page 14.

Lexmark E220

Limit label printing to occasional use of paper office labels designed for laser printers. We do not recommend using

vinyl or polyester labels.

The Lexmark E220 supports stocks up to 163 g/m

(43 lb). The automatic paper feeder can hold up to 10 sheets of card

stock or labels.

The following table lists the maximum weights supported by Tray 1 and the manual sheet feeder.

Printer specifications 67

Paper source

Card stock Labels

Index Bristol Tag Cover Paper Vinyl

Tray 1

163 g/m

—

163 g/m

—

Manual feed

163 g/m

—

163 g/m

—

For paper and transparency specifications, see the Lexmark E220 Publications CD.

Labels Width: 210–216 mm (8.3–8.5 in.)

Length: 279–297 mm (11–11.7 in.)

Weight:

Up to 163 g/m

(43 lb)

Thickness: Up to 0.25 mm (0.01 in.)

Smoothness: 100–400* Sheffield

* 150–250 Sheffield is optimal. Using media higher than 300 Sheffield could result in printing degradation.

Card stock Weight:

Up to 163 g/m

Index Bristol (90 lb)

Up to 163 g/m

Tag (100 lb)

Note: To minimize curl, use the top exit when printing on card stock and labels.

For more information, see “Maintenance procedures” on page 14.

Lexmark E230, E232, E234(n), E330, and E332n

Limit label printing to occasional use of paper office labels designed for laser printers. We do not recommend using

vinyl or polyester labels.

The Lexmark E230, E232, E234(n), E330, and E332n support paper and label stock from 60–90 g/m

(24 lb) and card

stock up to 163 g/m

(43 lb). The automatic paper feeder can hold up to 50 sheets of paper labels.

The following table lists the maximum weights supported by Tray 1 and the manual sheet feeder.

Paper source

Card stock Labels

Index Bristol Tag Cover Paper Vinyl

Tray 1 — — —

90 g/m

—

Manual feed

163 g/m

—

90 g/m

—

For paper and transparency specifications, see the Lexmark E230/E232/E234(n)/E330/E332n Publications CDs.

Printer specifications 68

Labels Width: 210–216 mm (8.3–8.5 in.)

Length: 279–297 mm (11–11.7 in.)

Weight:

Up to 90 g/m

(24 lb)

Thickness: Up to 0.25 mm (0.01 in.)

Smoothness: 100–400* Sheffield

*150–250 Sheffield is optimal. Using media higher than 300 Sheffield could result in printing degradation.

Card stock Weight:

Up to 163 g/m

Index Bristol (90 lb)

Up to 163 g/m

Tag (100 lb)

Note: To minimize curl, use the rear exit when printing on card stock and labels.

For more information, see “Maintenance procedures” on page 14.

Lexmark E238, E240, E240n, E340, and E342n

Limit label printing to occasional use of paper office labels designed for laser printers. We do not recommend using

vinyl or polyester labels.

The printer supports stocks up to 163 g/m

(43 lb). You can load up to 50 label sheets in Tray 1. Card stock must be sent

through the manual feeder one sheet at a time.

The following table lists the maximum weights supported by Tray 1, Tray 2, and the manual sheet feeder.

Paper source

Card Stock Labels

Index Bristol Tag Cover Paper Vinyl

Tray 1 — — —

90 g/m

—

Tray 2 — — —

90 g/m

—

Manual Feed

163 g/m

—

163 g/m

—

Note: The E238 printer does not support a second drawer option.

For paper and transparency specifications, refer to the printer publications CD.

Printer specifications 69

Labels Width: 89–216 mm (3.5–8.5 in.)

Length: 210–356 mm (8.27–14 in.)

Weight:

Up to 163 g/m

(43 lb)

Thickness: Up to 0.25 mm (0.01 in.)

Smoothness: 100–400* Sheffield

*150–250 Sheffield is optimal. Using media higher than 300 Sheffield could result in printing degradation.

Card stock Weight:

Up to 163 g/m

Index Bristol (90 lb)

Up to 163 g/m

Tag (100 lb)

Note: To minimize curl, use the rear exit when printing on card stock and labels.

For more information, see “Maintenance procedures” on page 14.

Lexmark E250, E350, and E450n

Limit label printing to occasional use of paper office labels designed for laser printers. We do not recommend using

vinyl or polyester labels.

The printer supports paper and label stock from 60–90 g/m

and index card stock up to 163 g/m

(43 lb). You can load

up to 50 label sheets in Tray 1. Card stock must be sent through the manual feeder one sheet at a time.

The following table lists the maximum weights supported by Tray 1, Tray 2, and the manual sheet feeder.

Paper source

Card Stock Labels

Index Bristol Tag Cover Paper Vinyl

Tray 1 — — —

90 g/m

—

Tray 2 — — —

90 g/m

—

Manual Feed

163 g/m

—

90 g/m

—

Card stock should be grain short and set to exit the rear door.

For paper and transparency specifications, refer to the printer publications CD.

Printer specifications 70

Labels Width: 210–216 mm (8.3–8.5 in.)

Length: 279–297 mm (11–11.7 in.)

Weight:

Up to 90 g/m

(24 lb)

Thickness: Up to 0.25 mm (0.01 in.)

Smoothness: 100–400* Sheffield

*150–250 Sheffield is optimal. Using media higher than 300 Sheffield could result in printing degradation.

Card stock Weight:

Up to 163 g/m

Index Bristol (90 lb)

Up to 163 g/m

Tag (100 lb)

Note: To minimize curl, use the rear exit when printing on card stock and labels.

For more information, see “Maintenance procedures” on page 14.

Lexmark E260, E260d, E260dn, E360d, E360dn, E460dn,

E460dw, and E462dtn

Limit label printing to occasional use of paper office labels designed for laser printers. We do not recommend using

vinyl or polyester labels.

The printer supports paper and label stock from 60–90 g/m

and index card stock up to 163 g/m

(43 lb). You can load

up to 50 label sheets in Tray 1. Card stock must be sent through the manual feeder one sheet at a time.

The following table lists the maximum weights supported by Tray 1, Tray 2, and the manual sheet feeder.

Paper source

Card Stock Labels

Index Bristol Tag Cover Paper

Tray 1 — — —

90 g/m

Tray 2 — — —

90 g/m

Manual Feed

163 g/m

—

90 g/m

Card stock should be grain short and set to exit the rear door.

For paper and transparency specifications, see the printer publications CD.

Printer specifications 71

Labels Width: 210–216 mm (8.3–8.5 in.)

Length: 279–297 mm (11–11.7 in.)

Weight:

Up to 90 g/m

(24 lb)

Thickness: Up to 0.25 mm (0.01 in.)

Smoothness: 100–200* Sheffield

*150–200 Sheffield is optimal. Using media higher than 300 Sheffield could result in printing degradation.

Card stock Weight:

Up to 163 g/m

Index Bristol (90 lb)

Up to 163 g/m

Tag (100 lb)

Note: To minimize curl, use the rear exit when printing on card stock and labels.

For more information, see “Maintenance procedures” on page 14.

Lexmark E320, E322

Limit label printing to occasional use of paper office labels designed for laser printers. We do not recommend using

vinyl or polyester labels.

The Lexmark E320 and Lexmark E322 support stocks up to 163 g/m

(43 lb). The automatic paper feeder can hold up

to 10 sheets of card stock or labels.

The following table lists the maximum weights supported by Tray 1 and the manual sheet feeder.

Paper source

Card stock Labels

Index Bristol Tag Cover Paper Vinyl

Tray 1

163 g/m

—

163 g/m

—

Manual feed

163 g/m

—

163 g/m

—

For paper and transparency specifications, see the Lexmark E320/E322 Publications CD.

Labels Width: 210–216 mm (8.3–8.5 in.)

Length: 279–297 mm (11–11.7 in.)

Weight:

Up to 163 g/m

(43 lb)

Thickness: Up to 0.25 mm (0.01 in.)

Smoothness: 100–400* Sheffield

Printer specifications 72

* 150–250 Sheffield is optimal. Using media higher than 300 Sheffield could result in printing degradation.

Card stock Weight:

Up to 163 g/m

Index Bristol (90 lb)

Up to 163 g/m

Tag (100 lb)

Note: To minimize curl, use the top exit when printing on card stock and labels.

For more information, see “Maintenance procedures” on page 14.

Lexmark E321, E323

Limit label printing to occasional use of paper office labels designed for laser printers. We do not recommend using

vinyl or polyester labels.

The Lexmark E321 and Lexmark E323 support stocks up to 163 g/m

(43 lb). The automatic paper feeder can hold up

to 10 sheets of card stock or labels.

The following table lists the maximum weights supported by Tray 1 and the manual sheet feeder.

Paper Source

Card Stock Labels

Index Bristol Tag Cover Paper Vinyl

Tray 1

163 g/m

—

163 g/m

—

Manual Feed

163 g/m

—

163 g/m

—

For paper and transparency specifications, see the Lexmark E321/E323 Publications CD.

Labels Width: 210–216 mm (8.3–8.5 in.)

Length: 279–297 mm (11–11.7 in.)

Weight:

Up to 163 g/m

(43 lb)

Thickness: Up to 0.25 mm (0.01 in.)

Smoothness: 100–400* Sheffield

* 150–250 Sheffield is optimal. Using media higher than 300 Sheffield could result in printing degradation.

Card stock Weight:

Up to 163 g/m

Index Bristol (90 lb)

Up to 163 g/m

Tag (100 lb)

Note: To minimize curl, use the top exit when printing on card stock and labels.

For more information, see “Maintenance procedures” on page 14.

Printer specifications 73

Lexmark MS310d, MS310dn, MS410d, MS410dn, MS510dn,

MS610dn, and MS610de

Limit label printing to occasional use of paper office labels designed for laser printers. The Lexmark MS310d, MS310dn,

MS410d, MS410dn, MS510dn, MS610dn, and MS610de printer models do not support vinyl, pharmacy, or polyester

labels. It is recommended to print no more than 20 pages of paper labels a month.

The printer and duplex path support 60–90 g/m

(16–24 lb) paper weights. The multipurpose feeder supports 60–

163 g/m

(16–43 lb) paper weights.

For the MS31x and MS41x printer models, you can load paper labels up to 50 sheets in the standard tray and up to the

full capacity of the optional trays. You can load up to 15 paper labels and up to 10 sheets of card stock in the multipurpose

feeder.

For the MS51x and MS61x printer models, you can load paper labels up to the full capacity of the standard tray and

the optional trays. You can load up to 30 paper labels and up to 20 sheets of card stock in the multipurpose feeder.

The following table lists the maximum weights supported by the standard tray, the optional 250‑ and 550‑sheet trays,

and the multipurpose and manual feeders.

Paper source

Card Stock Labels

Index Bristol Tag Cover Paper

Standard tray — — —

60–90 g/m

Optional 250‑sheet tray

Optional 550‑sheet tray

———

60–120 g/m

Manual feeder

Multipurpose feeder

60–163 g/m

—

60‑163 g/m

Printer specifications 74

Labels Width: 210–216 mm (8.3–8.5 in.)

Length: 279–297 mm (11–11.7 in.)

Weight:

Up to 163 g/m

(43 lb)

Thickness: Up to 0.25 mm (0.01 in.)

Smoothness: 100–400* Sheffield

*150–250 Sheffield is optimal. Using media higher than 300 Sheffield could result in printing degradation.

Card stock Weight:

Up to 163 g/m

Index Bristol (90 lb)

Up to 163 g/m

Tag (100 lb)

When printing on labels:

• Check with the manufacturer or vendor to ensure the labels can withstand temperatures up to 210°C (410°F) without

sealing, curling excessively, wrinkling, or releasing hazardous emissions.

• Check with the manufacturer or vendor to ensure the labels can withstand 25 psi (172 kPa) pressure without

delaminating, oozing around the edges, or releasing hazardous fumes.

• Do not use labels with slick backing material.

• Use full label sheets. Partial sheets may cause labels to peel off during printing, resulting in a jam.

• Do not use labels with exposed adhesive.

• Do not print within 1 mm (0.04 in.) of the edge of the label, of the perforations, or between die‑cuts on the label.

• Be sure adhesive backing does not reach to the sheet edge. Zone coating of the adhesive at least 1 mm (0.04 in.)

away from the edges is recommended. Adhesive material contaminates the printer and could void the warranty.

• If zone coating of the adhesive is not possible, remove a 1.6 mm (0.06 in.) strip on the leading and driver edge, and

use a non‑oozing adhesive.

• Portrait orientation works best, especially when printing bar codes.

When printing on card stock:

• Make sure the Paper Type is Card Stock.

• Select the Paper Texture setting.

• Be aware that preprinting, perforation, and creasing may significantly affect the print quality and cause jams or

other paper handling problems.

• Check with the manufacturer or vendor to ensure the card stock can withstand temperatures up to 210°C (410°F)

without releasing hazardous emissions.

• Do not use preprinted card stock manufactured with chemicals that may contaminate the printer.

• Use grain short card stock when possible.

For more information, see

“Maintenance procedures” on page 14.

Printer specifications 75

Lexmark MS710 and MS711

The Lexmark MS710 and MS711 printer models print on many labels, which includes vinyl and polyester, designed for

use with laser printers.

The following table lists the maximum weights supported by the trays and the multipurpose feeder.

Paper source

Card stock

Labels

Index Bristol Tag Cover Paper

Dual‑web

paper

Polyester Vinyl

Standard and

optional 250‑ and

550‑sheet trays

199 g/m

203 g/m

176 g/m

180 g/m

220 g/m

300 g/m

Multipurpose

feeder

199 g/m

203 g/m

176 g/m

180 g/m

220 g/m

260 g/m

See “Grain orientation” on page 17 for specific recommendations.

Due to label design characteristics, unacceptable feeding may be experienced from the multipurpose feeder.

Labels Thickness: 0.102–0.305 mm (0.004–0.012 in.)

Smoothness: 100–400* Sheffield

*150–250 Sheffield is optimal. Using media higher than 300 Sheffield could result in printing degradation.

Card stock Weight:

Up to 199 g/m

Index Bristol (110 lb)

Up to 203 g/m

Tag (125 lb)

Up to 176 g/m

Cover (65 lb)

Card stock and label guidelines

Labels are one of the most difficult print materials for laser printers. A special fuser cleaner should be used for label

applications to optimize feed reliability.

Printing labels on the Lexmark MS710 and MS711 requires a special label fuser cleaner that prevents duplexing.

It is recommended that when you run labels, you install a special oil fuser cleaner, P/N 40X8579. When you order a

new cartridge, make sure the cartridge includes the correct fuser cleaner.

Printer specifications 76

It is possible to duplex certain labels that have been specifically designed for this application. To duplex labels, consult

the Lexmark "Converter Lists" to see which converters have successfully developed this type of label, and you must

install a special fuser wiper. The wax wiper that is used with the Lexmark MS710 and MS711 is P/N 40X8581. Cartridges

designed for duplex label printing contain two wax wipers. Change the wax wiper at the halfway point of your normal

cartridge usage to provide additional cleaning and optimize performance. Contact your Supplies and Label Specialist

for information on oil and wax vinyl label cartridges.

Note: Wax wipers are not recommended when using vinyl labels.

Tray fill line information

Depending on construction, labels and card stock can sometimes be difficult to pick and feed reliably. Performance can

be improved by controlling the number of sheets of media loaded in the tray. There are two fill lines in the tray. The

solid line is the maximum paper fill indicator. No media should be loaded in the tray above this line or paper jams could

occur. The dashed line is the alternate paper fill indicator and should be used if any feed or reliability issues are noted

with specialty media, including labels and card stock. If paper jams occur when completely filling the tray, load the

specialty media only up to the alternate paper fill indicator.

For more information on the printer models and feeding different types of media, contact your Lexmark sales

representative.

When printing on labels:

• From the printer control panel, set the paper size, type, texture, and weight in the Paper menu to match the labels

loaded in the tray.

• Do not load labels together with paper or transparencies in the same paper tray. Combining print materials can

cause feeding problems.

• Use full label sheets. Partial sheets may cause labels to peel off during printing, resulting in a paper jam. Adhesive

material may contaminate your printer. It could also void your printer and cartridge warranties.

When feeding labels, the number of labels per sheet can affect registration more than basis weight. Typically, the more

labels per sheet, the better the registration.

Printer specifications 77

When printing on card stock:

• From the printer control panel, set the paper size, type, texture, and weight in the Paper menu to match the card

stock loaded in the tray.

• Do not use card stock that is creased. It may cause paper jams.

For more information, see the following:

• “Pick roller technology” on page 11

• “Grain orientation” on page 17

• “Maintenance procedures” on page 14

• “Troubleshooting” on page 14

• “Primary rib pattern design guidelines for reference edge alignment” on page 22

Lexmark MS810, MS811, and MS812

The Lexmark MS810, MS811, and MS812 printer models print on many labels designed for use with laser printers.

However the MS81x and MS71x printer models have been specifically designed for slightly different media applications.

The MS81x printer models should not be used in the following customer applications:

• Vinyl and Polyester labels

For applications where these labels are run, the MS71x printer models are recommended.

• Narrow Media Batch Jobs

The MS810 printer model supports many standard and custom paper sizes. When printing on paper less than

210 mm (8.3 inches) wide, the printer speed may decrease. If you print large jobs on narrow paper regularly, consider

the MS71x printer models, which are designed to print batches of 10 or more pages of narrow paper at a faster

speed.

Note: For the MS81x printer models, A5 default orientation is Landscape, which is also called as LEF, and thus A5

is not considered as narrow media.

If vinyl labels are printed on the MS81x printer models, this can lead to print quality problems and printer damage. If

narrow media batch jobs are printed, printer throughput could be substantially reduced. If either of these applications

are being considered for the MS81x printer models, then contact your Lexmark sales representative for more

information about the MS71x printer models.

The following table lists the maximum weights supported by the trays and the multipurpose feeder:

Printer specifications 78

Paper source

Card stock

Labels

Index Bristol Tag Cover Paper Dual‑web paper

Standard and optional

250‑ and 550‑sheet trays

199 g/m

203 g/m

176 g/m

180 g/m

Multipurpose feeder

199 g/m

203 g/m

176 g/m

180 g/m

See “Grain orientation” on page 17 for specific recommendations.

Due to label design characteristics, unacceptable feeding may be experienced from the multipurpose feeder.

Labels Thickness: 0.102–0.305 mm (0.004–0.012 in.)

Smoothness: 100–400* Sheffield

*150–250 Sheffield is optimal. Using media higher than 300 Sheffield could result in printing degradation.

Card stock Weight:

Up to 199 g/m

Index Bristol (110 lb)

Up to 203 g/m

Tag (125 lb)

Up to 176 g/m

Cover (65 lb)

Card stock and label guidelines

Tray fill line information

Depending on construction, labels and card stock can sometimes be difficult to pick and feed reliably. Performance can

be improved by controlling the number of sheets of media loaded in the tray. There are two fill lines in the tray. The

solid line is the maximum paper fill indicator. No media should be loaded in the tray above this line or paper jams could

occur. The dashed line is the alternate paper fill indicator and should be used if any feed or reliability issues are noted

with specialty media, including labels and card stock. If paper jams occur when completely filling the tray, load the

specialty media only up to the alternate paper fill indicator.

Printer specifications 79

When printing on labels:

• From the printer control panel, set the paper size, type, texture, and weight in the Paper menu to match the labels

loaded in the tray.

• Do not load labels together with paper or transparencies in the same paper tray. Combining print materials can

cause feeding problems.

• Use full label sheets. Partial sheets may cause labels to peel off during printing, resulting in a paper jam. Adhesive

material may contaminate your printer. It could also void your printer and cartridge warranties.

When feeding labels, the number of labels per sheet can affect registration more than basis weight. Typically, the more

labels per sheet, the better the registration.

When printing on card stock:

• From the printer control panel, set the paper size, type, texture, and weight in the Paper menu to match the card

stock loaded in the tray.

• Do not use card stock that is creased. It may cause paper jams.

For more information, see the following:

• “Pick roller technology” on page 11

• “Grain orientation” on page 17

• “Maintenance procedures” on page 14

• “Troubleshooting” on page 14

• “Primary rib pattern design guidelines for reference edge alignment” on page 22

Lexmark MX310dn, MX410de, MX510de, MX511de,

MX511dhe, MX610de, MX611de, and MX611dhe

Limit label printing to occasional use of paper office labels designed for laser printers. The Lexmark MX310dn, MX410de,

MX510de, MX511de, MX511dhe, MX610de, MX611de, and MX611dhe printer models do not support vinyl, pharmacy,

or polyester labels. It is recommended to print no more than 20 pages of paper labels a month.

The printer and duplex path support 60–90 g/m

(16–24 lb) paper weights. The multipurpose feeder supports 60–

163 g/m

(16–43 lb) paper weights.

Printer specifications 80

For the MX31x and MX41x printer models, you can load paper labels up to 50 sheets in the standard tray and up to the

full capacity of the optional trays. You can load up to 15 paper labels and up to 10 sheets of card stock in the multipurpose

feeder.

For the MX51x and MX61x printer models, you can load paper labels up to the full capacity of the standard tray and

optional trays. You can load up to 30 paper labels and up to 20 sheets of card stock in the multipurpose feeder.

The following table lists the maximum weights supported by the standard tray, optional 250‑ and 550‑sheet trays, and

multipurpose and manual feeders.

Paper source

Card Stock Labels

Index Bristol Tag Cover Paper

Standard tray — — —

60–90 g/m

Optional 250‑sheet tray

Optional 550‑sheet tray

———

60–120 g/m

Manual feeder

Multipurpose feeder

60–163 g/m

—

60‑163 g/m

Labels Width: 210–216 mm (8.3–8.5 in.)

Length: 279–297 mm (11–11.7 in.)

Weight:

Up to 163 g/m

(43 lb)

Thickness: Up to 0.25 mm (0.01 in.)

Smoothness: 100–400* Sheffield

*150–250 Sheffield is optimal. Using media higher than 300 Sheffield could result in printing degradation.

Card stock Weight:

Up to 163 g/m

Index Bristol (90 lb)

Up to 163 g/m

Tag (100 lb)

When printing on labels:

• Check with the manufacturer or vendor to ensure the labels can withstand temperatures up to 210°C (410°F) without

sealing, curling excessively, wrinkling, or releasing hazardous emissions.

• Check with the manufacturer or vendor to ensure the labels can withstand 25 psi (172 kPa) pressure without

delaminating, oozing around the edges, or releasing hazardous fumes.

• Do not use labels with slick backing material.

• Use full label sheets. Partial sheets may cause labels to peel off during printing, resulting in a jam.

• Do not use labels with exposed adhesive.

• Do not print within 1 mm (0.04 in.) of the edge of the label, of the perforations, or between die‑cuts on the label.

• Be sure adhesive backing does not reach to the sheet edge. Zone coating of the adhesive at least 1 mm (0.04 in.)

away from the edges is recommended. Adhesive material contaminates the printer and could void the warranty.

• If zone coating of the adhesive is not possible, remove a 1.6 mm (0.06 in.) strip on the leading and driver edge, and

use a non‑oozing adhesive.

• Portrait orientation works best, especially when printing bar codes.

When printing on card stock:

• Make sure the Paper Type is Card Stock.

• Select the Paper Texture setting.

Printer specifications 81

• Be aware that preprinting, perforation, and creasing may significantly affect the print quality and cause jams or

other paper handling problems.

• Check with the manufacturer or vendor to ensure the card stock can withstand temperatures up to 210°C (410°F)

without releasing hazardous emissions.

• Do not use preprinted card stock manufactured with chemicals that may contaminate the printer.

• Use grain short card stock when possible.

For more information, see

“Maintenance procedures” on page 14.

Lexmark MX710, MX711, MX810, MX811, and MX812

The Lexmark MX710, MX711, MX810, MX811, and MX812 printer models print on many labels designed for use with

laser printers. However the MX71x, MX81x, and MS71x printer models have been specifically designed for slightly

different media applications.

The MX81x printer models should not be used in the following customer applications:

• Vinyl and Polyester labels

For applications where these labels are run, the MS71x printer models are recommended.

• Narrow Media Batch Jobs

The MX810 printer model supports many standard and custom paper sizes. When printing on paper less than

210 mm (8.3 inches) wide, the printer speed may decrease. If you print large jobs on narrow paper regularly, then

consider the MS71x printer models, which are designed to print batches of 10 or more pages of narrow paper at a

faster speed.

Note: For the MX81x printer models, A5 default orientation is Landscape, which is also called as LEF, and thus

A5 is not considered as narrow media.

If vinyl labels are printed on the MX71x or MX81x printer models, this can lead to print quality problems and printer

damage. If narrow media batch jobs are printed, printer throughput could be substantially reduced. If either of these

applications are being considered for the MX71x or MX81x printer models, then contact your Lexmark sales

representative for more information about the MS71x printer models.

The following table lists the maximum weights supported by the trays and the multipurpose feeder.

Printer specifications 82

Note: Scanning labels through the ADF is not recommended.

Paper source

Card stock

Labels

Index Bristol Tag Cover Paper Dual‑web paper

Standard and optional

250‑ and 550‑sheet

trays

199 g/m

203 g/m

176 g/m

180 g/m

Multipurpose feeder

199 g/m

203 g/m

176 g/m

180 g/m

See “Grain orientation” on page 17 for specific recommendations.

Due to label design characteristics, unacceptable feeding may be experienced from the multipurpose feeder.

Labels Thickness: 0.102–0.305 mm (0.004–0.012 in.)

Smoothness: 100–400* Sheffield

* 150–250 Sheffield is optimal. Using media higher than 300 Sheffield could result in printing degradation.

Card stock Weight:

Up to 199 g/m

Index Bristol (110 lb)

Up to 203 g/m

Tag (125 lb)

Up to 176 g/m

Cover (65 lb)

Card stock and label guidelines

Tray fill line information

Depending on construction, labels and card stock can sometimes be difficult to pick and feed reliably. Performance can

be improved by controlling the number of sheets of media loaded in the tray. There are two fill lines in the tray. The

solid line is the maximum paper fill indicator. No media should be loaded in the tray above this line or paper jams could

occur. The dashed line is the alternate paper fill indicator and should be used if any feed or reliability issues are noted

with specialty media, including labels and card stock. If paper jams occur when completely filling the tray, load the

specialty media only up to the alternate paper fill indicator.

Printer specifications 83

When printing on labels:

• From the printer control panel, set the paper size, type, texture, and weight in the Paper menu to match the labels

loaded in the tray.

• Do not load labels together with paper or transparencies in the same paper tray. Combining print materials can

cause feeding problems.

• Use full label sheets. Partial sheets may cause labels to peel off during printing, resulting in a paper jam. Adhesive

material may contaminate your printer. It could also void your printer and cartridge warranties.

When feeding labels, the number of labels per sheet can affect registration more than basis weight. Typically, the more

labels per sheet, the better the registration.

When printing on card stock:

• From the printer control panel, set the paper size, type, texture, and weight in the Paper menu to match the card

stock loaded in the tray.

• Do not use card stock that is creased. It may cause paper jams.

For more information, see the following:

• “Pick roller technology” on page 11

• “Grain orientation” on page 17

• “Maintenance procedures” on page 14

• “Troubleshooting” on page 14

• “Primary rib pattern design guidelines for reference edge alignment” on page 22

Printer specifications 84

Lexmark T420

The Lexmark T420 prints on many labels designed for use with laser printers.

The Lexmark T420 supports stocks up to 60‑199 g/m

(16–53 lb). The standard tray is designed to handle 100 sheets

of heavy labels, but its capacity may be reduced due to the thickness of some labels. The multipurpose feeder can feed

up to 30 sheets of dual‑web or integrated labels and 10 sheets of card stock.

The following tables list the maximum weights supported by Tray 1 and the multipurpose feeder.

Paper source

Card stock

Index Bristol Tag Cover

Tray 1 — — —

Multipurpose feeder*

60–199 g/m

(16–53 lb)

—

* Card stock can only be fed from the multipurpose feeder and must always exit to the rear output bin.

Label type

Print media source

Standard tray Multipurpose feeder Optional trays

Paper

Integrated X

Dual web

Vinyl X X X

‑ indicates support

X ‑ indicates no support

Note: Do not place over 100 label sheets in the standard tray or over 30 label sheets in the multipurpose feeder.

Warning—Potential Damage: Feeding labels from print media sources that are not supported may damage your printer.

For paper and transparency specifications, see the Lexmark T420 Publications CD.

Labels Width: 76.2–216 mm (3.0–8.5 in.)

Length: 127–355.6 mm (5–14 in.)

Weight:

Up to 199 g/m

(53 lb)

Thickness: Up to 0.25 mm (0.01 in.)

Smoothness: 100–400* Sheffield

* 150–250 Sheffield is optimal. Using media higher than 300 Sheffield could result in printing degradation.

Printer specifications 85

Card stock Weight:

Up to 163 g/m

Index Bristol (90 lb)

Up to 163 g/m

Tag (100 lb)

Note: Always use the rear exit when printing on card stock. To minimize curl, use the rear exit when printing on labels.

Card stock and label guidelines

When printing on labels:

• Set the Paper Type to Labels from the printer driver, the Local Printer Setup Utility, or MarkVision.

• Do not load labels together with paper or transparencies in the same paper source.

• Do not use label sheets with a slick backing material.

• Do not print within 1 mm (0.040 in.) of the die‑cut.

• Use full label sheets. Partial sheets may cause labels to peel off during printing, resulting in a paper jam. Partial

sheets will also contaminate the printer and the cartridge with adhesive, and could void the printer and cartridge

warranties.

• Use labels that can withstand temperatures of 205°C (401°F) without sealing, excessive curling, wrinkling, or

releasing hazardous emissions.

• Use labels that can withstand pressure of 25 pounds per square inch (psi).

• Do not print within 1 mm (0.040 in.) of the edge of the label, of the perforations, or between die-cuts of the label.

• Do not use labels that have adhesive to the edge of the sheet. We recommend zone coating of the adhesive at least

1 mm (0.040 in.) from the edges. Adhesive material will contaminate the printer and could void the warranty.

• If zone coating of the adhesive is not possible, a 3‑mm (0.125‑in.) strip should be removed on the leading and driver

edge, and a non‑oozing adhesive should be used.

• Remove a 3‑mm (0.125‑in.) strip from the leading edge to prevent labels from peeling inside the printer.

• Portrait orientation is preferred, especially when printing bar codes.

• Do not use labels that have exposed adhesive.

• For the multipurpose feeder, load labels with the recommended print side faceup and the top edge going in first.

For the tray, load labels with the recommended print side facedown.

When printing on card stock:

• Set the Paper Type to Card Stock from the printer driver, the Local Printer Setup Utility, or MarkVision.

• Do not use preprinted card stock manufactured with chemicals that may contaminate the printer. Preprinting

introduces semi‑liquid and volatile components into the printer.

• Do not use card stock that is creased. It may cause paper jams.

• We recommend the use of grain short card stock.

• Load card stock with the recommended print side faceup and the top edge going in first.

For more information, see

“Maintenance procedures” on page 14.

Printer specifications 86

Lexmark T430

The Lexmark T430 prints on paper office labels designed for laser printers. Limit label printing to occasional use. We

do not recommend using vinyl or polyester labels.

The Lexmark T430 supports stocks from 60–163 g/m

(16‑43 lb). The multipurpose feeder can feed up to 30 sheets of

dual‑web or integrated labels and 10 sheets of card stock.

The following tables list the maximum weights supported by Tray 1 and the multipurpose feeder.

Paper source Index Bristol Tag Cover

Tray 1 — — —

Multipurpose Feeder*

60–163 g/m

(16–43 lb)

—

* Card stock can only be fed from the multipurpose feeder and must always exit to the rear output bin.

Label type Standard tray Multipurpose feeder Optional trays

Paper X

Integrated X

Dual web X

‑ indicates support

X ‑ indicates no support

Note: Do not place over 100 label sheets in the standard tray or over 30 label sheets in the multipurpose feeder.

Warning—Potential Damage: Feeding labels from print media sources that are not supported may damage your printer.

Labels Width: 76.2–216 mm (3.0–8.5 in.)

Length: 127–355.6 mm (5–14 in.)

Weight:

Up to 199 g/m

(53 lb)

Thickness: Up to 0.25 mm (0.01 in.)

Smoothness: 100–400* Sheffield

* 150 ‑ 250 Sheffield is optimal. Using media higher than 300 Sheffield could result in printing

degradation.

Card stock Weight:

Up to 163 g/m

Index Bristol (90 lb)

Up to 163 g/m

Tag (100 lb)

Note: Always use the rear exit when printing on card stock. To minimize curl, use the rear exit when printing on labels.

Printer specifications 87

Card stock and label guidelines

When printing on labels:

• Set the Paper Type to Labels from the printer driver, the Local Printer Setup Utility, or MarkVision.

• Do not load labels together with paper or transparencies in the same paper source.

• Do not use label sheets with a slick backing material.

• Do not print within 1 mm (0.040 in.) of the die-cut.

• Use full label sheets. Partial sheets may cause labels to peel off during printing, resulting in a paper jam. Partial

sheets will also contaminate your printer and your cartridge with adhesive, and could void your printer and cartridge

warranties.

• Use labels that can withstand temperatures of 205°C (401°F) without sealing, excessive curling, wrinkling, or

releasing hazardous emissions.

• Use labels that can withstand pressure of 25 pounds per square inch (psi).

• Do not print within 1 mm (0.040 in.) of the edge of the label, of the perforations, or between die-cuts of the label.

• Do not use label sheets that have adhesive to the edge of the sheet. We recommend zone coating of the adhesive

at least 1 mm (0.040 in.) away from edges. Adhesive material will contaminate your printer and could void your

warranty.

• If zone coating of the adhesive is not possible, a non‑oozing adhesive should be used. Unlike other printers, do not

remove the leading or driver edge.

• The perforation locations may impact printer reliability.

Note: Test any perforated card stock or paper before purchasing large quantities.

• Portrait orientation is preferred, especially when printing bar codes.

• Do not use labels that have exposed adhesive.

• For the multipurpose feeder, load labels with the recommended print side faceup and the top edge going in first.

For the tray, load labels with the recommended print side facedown.

When printing on card stock:

• Set the Paper Type to Card Stock from the printer driver, the Local Printer Setup Utility, or MarkVision.

• Do not use preprinted card stock manufactured with chemicals that may contaminate the printer. Preprinting

introduces semi‑liquid and volatile components into the printer.

• Do not use card stock that is creased. It may cause paper jams.

• We recommend the use of grain short card stock.

• Load card stock with the recommended print side faceup and the top edge going in first.

For more information, see

“Maintenance procedures” on page 14.

Printer specifications 88

Lexmark T520, T522

The Lexmark T520 and T522 print on many labels designed for use with laser printers.

The following table lists the maximum weights supported by the trays and the multipurpose feeder.

Print material

Range or maximum weight supported

Integrated tray and optional

500‑sheet drawer

Multipurpose feeder

and optional

250‑sheet drawer

Paper

(grain direction

)

Xerographic or business paper

60–176 g/m

(16–47 lb bond)

60–135 g/m

(16–36 lb bond)

Card Stock

(grain direction

)

Index Bristol

199 g/m

(110 lb) 163 g/m

(90 lb)

Tag

203 g/m

(125 lb) 163 g/m

(100 lb)

Cover

216 g/m

(80 lb) 176 g/m

(65 lb)

Labels Paper

180 g/m

(48 lb bond) 163 g/m

(43 lb bond)

Dual‑web paper

180 g/m

(48 lb bond) 163 g/m

(43 lb bond)

Vinyl

300 g/m

(92 lb liner) 260 g/m

(78 lb liner)

Polyester

220 g/m

(59 lb bond) 220 g/m

(59 lb bond)

Integrated forms

Pressure sensitive area

140–175 g/m

Paper base (grain long)

75–135 g/m

(20–36 lb bond)

75–135 g/m

(20–36 lb bond)

See “Grain orientation” on page 17 for specific recommendations.

Pressure‑sensitive area must enter the printer first for grain short paper.

Due to label design characteristics, unacceptable feeding may be experienced from the multipurpose feeder.

For paper and transparency specifications, see the printer publications CD.

The following table indicates the paper sizes each tray supports.

Printer specifications 89

Source

Standard sizes

(width x length)

Universal sizes

(width x length)

Minimum Maximum Minimum Maximum

Standard tray,

250‑sheet drawer,

500‑sheet drawer

148 x 210 mm

(5.83 x 8.27 in.)

215.9 x 355.6 mm

(8.5 x 14 in.)

139.7 x 210 mm

(5.5 x 8.27 in.)

215.9 x 355.6 mm

(8.5 in. x 14 in.)

Multipurpose

feeder*

148 x 210 mm

(5.83 x 8.27 in.)

215.9 x 355.6 mm

(8.5 x 14 in.)

69.85 x 127 mm

(2.75 in. x 5 in.)

229 x 355.6 mm

(9.01 x 14 in.)

* If you load paper that is narrower than 148 mm (5.83 in.) in the multipurpose feeder (for example, 3 x 5‑inch index cards),

set the MP Feeder Size menu item to Universal.

Labels Thickness: 0.102–0.305 mm (0.004–0.012 in.)

Smoothness: 100–400* Sheffield

* 150–250 Sheffield is optimal. Using media higher than 300 Sheffield could result in printing degradation.

Card stock Weight:

Up to 199 g/m

Index Bristol (90 lb)

Up to 203 g/m

Tag (100 lb)

Standard trays and special media trays

The Lexmark T520 and T522 paper feeding mechanism uses advanced technology that enhances feeding reliability. The

standard Lexmark T520 and T522 tray, which holds 250 or 500 sheets of 20‑lb xerographic paper, reliably feeds all

media tested according to the guidelines specified under

“Dimensions” on page 9.

For those difficult‑to‑print sizes, such as 3 x 5‑inch index cards, Lexmark offers a variety of special media trays and

drawers.

Note: Optional 250‑sheet Universally Adjustable Trays can be used to print forms with a minimum length of 5 inches

using a T520, when installed either in the integral tray location or in a 250‑sheet drawer under a 250‑sheet integral

tray. Optional 250‑sheet Universally Adjustable Trays support forms with a minimum length of 7 inches on a T522.

Optional 400‑sheet Universally Adjustable Trays support forms with a minimum length of 7 inches on both the T520

and T522.

Source Part number

250‑Sheet Special Media Tray 11K1572

250‑Sheet Special Media Drawer 11K1573

250‑Sheet Universally Adjustable Tray 11K1574

250‑Sheet Universally Adjustable Drawer 11K1878

500‑Sheet Special Media Tray 11K1921

500‑Sheet Special Media Tray + Drawer 11K1922

400‑Sheet Universally Adjustable Tray 11K1941

400‑Sheet Universally Adjustable Tray + Drawer 11K1942

Printer specifications 90

Card stock and label guidelines

Labels are one of the most difficult print materials for laser printers. A special fuser cleaner should be used for label

applications to optimize feed reliability. See your printer documentation for information on ordering additional label

fuser cleaners.

When printing on labels:

• Using the printer operator panel, set the Paper Type to Labels in the Paper Menu. For vinyl and other heavy labels,

set the Labels Weight (under the Paper Weight menu) to Heavy, and set the Labels Texture (under the Paper Texture

menu) to Smooth.

• Do not load labels together with paper or transparencies in the same paper tray. Combining print materials can

cause feeding problems.

• Use full label sheets. Partial sheets may cause labels to peel off during printing, resulting in a paper jam. Adhesive

material may contaminate your printer. It could also void your printer and cartridge warranties.

When feeding labels, the number of labels per sheet can affect registration more than basis weight. Typically, the more

labels per sheet, the better the registration.

When printing on card stock:

• Set the Paper Type to Card Stock in the Paper Menu.

• Do not use card stock that is creased. It may cause paper jams.

For more information, see the following:

• “Pick roller technology” on page 11

• “Grain orientation” on page 17

• “Maintenance procedures” on page 14

• “Troubleshooting” on page 14

Lexmark T620, T622

The Lexmark T620 and T622 print on many labels designed for use with laser printers.

The following table lists the maximum weights supported by the trays and the multipurpose feeder.

Printer specifications 91

Print Material

Range or maximum weight supported

250‑sheet and 500‑sheet trays

Multipurpose feeder

and optional

250‑sheet drawer

Paper

(grain long)

Xerographic or business paper

60–176 g/m

(16–47 lb bond)

60–135 g/m

(16–36 lb bond)

Card stock

(grain long

)

Index Bristol

163 g/m

(90 lb) 120 g/m

(67 lb)

Tag

163 g/m

(100 lb) 120 g/m

(74 lb)

Cover

176 g/m

(65 lb) 135 g/m

(50 lb)

Card stock

(grain short

)

Index Bristol

199 g/m

(110 lb) 163 g/m

(90 lb)

Tag

203 g/m

(125 lb) 163 g/m

(100 lb)

Cover

216 g/m

(80 lb) 176 g/m

(65 lb)

Labels Paper

180 g/m

(48 lb bond) 163 g/m

(43 lb bond)

Dual‑Web Paper

180 g/m

(48 lb bond) 163 g/m

(43 lb bond)

Vinyl

300 g/m

(92 lb liner) 260 g/m

(78 lb liner)

Polyester

220 g/m

(59 lb bond) 220 g/m

(59 lb bond)

Integrated forms

Pressure sensitive area

140–175 g/m

Paper base (grain long)

75–135 g/m

(20–36 lb bond)

75–135 g/m

(20–36 lb bond)

See “Grain orientation” on page 17 for specific recommendations.

The Lexmark T622 does not support vinyl labels.

Pressure‑sensitive area must enter the printer first for grain short paper.

Due to label design characteristics, unacceptable feeding may be experienced from the multipurpose feeder.

For paper and transparency specifications, see the publications CD.

The following table indicates the paper sizes each tray supports.

Source

Standard sizes

(width x length)

Universal sizes

(width x length)

Minimum Maximum Minimum Maximum

Standard tray,

250‑sheet drawer,

500‑sheet drawer

148 x 210 mm

(5.83 x 8.27 in.)

215.9 x 355.6 mm

(8.5 x 14 in.)

139.7 x 210 mm

(5.5 x 8.27 in.)

215.9 x 355.6 mm

(8.5 in. x 14 in.)

Multipurpose

feeder*

148 x 210 mm

(5.83 x 8.27 in.)

215.9 x 355.6 mm

(8.5 x 14 in.)

69.85 x 127 mm

(2.75 in. x 5 in.)

229 x 355.6 mm

(9.01 x 14 in.)

* If you load paper that is narrower than 148 mm (5.83 in.) in the multipurpose feeder (for example, 3 x 5‑inch index cards),

set the MP Feeder Size menu item to Universal.

Labels Thickness: 0.102–0.305 mm (0.004–0.012 in.)

Smoothness: 100–400* Sheffield

Printer specifications 92

* 150–250 Sheffield is optimal. Using media higher than 300 Sheffield could result in printing degradation.

Card stock Weight:

Up to 199 g/m

Index Bristol (90 lb)

Up to 203 g/m

Tag (100 lb)

Standard trays and special media trays

The Lexmark T620 and T622 paper feeding mechanism uses advanced technology that enhances feeding reliability. The

standard Lexmark T620 and T622 tray, which holds 500 sheets of bond paper, reliably feeds all media tested according

to the guidelines specified under

“Dimensions” on page 9.

For those difficult‑to‑print sizes, such as 3 x 7‑inch forms, Lexmark offers a variety of special media trays and drawers.

Note: Optional 250‑sheet Universally Adjustable Trays support forms with a minimum length of 7 inches on both the

T620 and T622. Optional 400‑sheet Universally Adjustable Trays support forms with a minimum length of 7 inches on

both the T620 and T622.

Source Part number

250‑Sheet Special Media Tray 11K1572

250‑Sheet Special Media Drawer 11K1573

250‑Sheet Universally Adjustable Tray 11K1574

250‑Sheet Universally Adjustable Drawer 11K1878

500‑Sheet Special Media Tray 11K1921

500‑Sheet Special Media Tray + Drawer 11K1922

400‑Sheet Universally Adjustable Tray 11K1941

400‑Sheet Universally Adjustable Tray + Drawer 11K1942

Card stock and label guidelines

Labels are one of the most difficult print materials for laser printers. A special fuser cleaner should be used for label

applications to optimize feed reliability. See your printer documentation for information on ordering additional label

fuser cleaners.

Printing labels on the T620 and T622 requires a special label fuser cleaner that prevents duplexing.

It is recommended that when you run vinyl labels, you install a special oil fuser cleaner, P/N 99A0725. When you order

a new cartridge, be sure to order the cartridge that will include the correct fuser cleaner.

It is possible to duplex certain labels that have been specifically designed for this application. To duplex labels, consult

the Lexmark “Converter Lists” to see which converters have successfully developed this type of label, and you must

install a special fuser wiper. The wax wiper that is used with the T620 and T622 is P/N 18A1467.

When printing on labels:

• Using the printer operator panel, set the Paper Type to Labels in the Paper Menu. For vinyl and other heavy labels,

set the Labels Weight (under the Paper Weight menu) to Heavy, and set the Labels Texture (under the Paper Texture

menu) to Smooth.

• Do not load labels together with paper or transparencies in the same paper tray. Combining print materials can

cause feeding problems.

• Use full label sheets. Partial sheets may cause labels to peel off during printing, resulting in a paper jam. Adhesive

material may contaminate your printer. It could also void your printer and cartridge warranties.

Printer specifications 93

Note: The Lexmark T622 does not support vinyl labels.

When feeding labels, the number of labels per sheet can affect registration more than basis weight. Typically, the more

labels per sheet, the better the registration.

When printing on card stock:

• Set the Paper Type to Card Stock in the Paper Menu.

• Do not use card stock that is creased. It may cause paper jams.

For more information, see the following:

• “Pick roller technology” on page 11

• “Grain orientation” on page 17

• “Maintenance procedures” on page 14

• “Troubleshooting” on page 14

Lexmark T630, T632, T634

The Lexmark T630, T632, and T634 print on many labels designed for use with laser printers.

The following table lists the maximum weights supported by the trays and the multipurpose feeder.

Print material

Range or maximum weight supported

250‑sheet and 500‑sheet trays

Multipurpose feeder

and

optional 250‑sheet drawer

Paper

(grain long)

Xerographic or business paper

60–176 g/m

(16–47 lb bond)

60–135 g/m

(16–36 lb bond)

Card stock

(grain long

)

Index Bristol

163 g/m

(90 lb) 120 g/m

(67 lb)

Tag

163 g/m

(100 lb) 120 g/m

(74 lb)

Cover

176 g/m

(65 lb) 135 g/m

(50 lb)

See “Grain orientation” on page 17 for specific recommendations.

Due to label design characteristics, unacceptable feeding may be experienced from the multipurpose feeder.

Pressure‑sensitive area must enter the printer first for grain short paper.

Printer specifications 94

Print material

Range or maximum weight supported

250‑sheet and 500‑sheet trays

Multipurpose feeder

and

optional 250‑sheet drawer

Card stock

(grain short

)

Index Bristol

199 g/m

(110 lb) 163 g/m

(90 lb)

Tag

203 g/m

(125 lb) 163 g/m

(100 lb)

Cover

216 g/m

(80 lb) 176 g/m

(65 lb)

Labels Paper

180 g/m

(48 lb bond) 163 g/m

(43 lb bond)

Dual‑Web Paper

180 g/m

(48 lb bond) 163 g/m

(43 lb bond)

Vinyl

300 g/m

(92 lb liner) 260 g/m

(78 lb liner)

Polyester

220 g/m

(59 lb bond) 220 g/m

(59 lb bond)

Integrated forms

Pressure‑sensitive area

140–175 g/m

Paper base (grain long)

75–135 g/m

(20–36 lb bond)

75–135 g/m

(20–36 lb bond)

See “Grain orientation” on page 17 for specific recommendations.

Due to label design characteristics, unacceptable feeding may be experienced from the multipurpose feeder.

Pressure‑sensitive area must enter the printer first for grain short paper.

For paper and transparency specifications, see the publications CD.

The following table indicates the paper sizes each tray supports.

Source

Standard sizes

(width x length)

Universal sizes

(width x length)

Minimum Maximum Minimum Maximum

Standard tray,

250‑sheet drawer,

500‑sheet drawer

148 x 210 mm

(5.83 x 8.27 in.)

215.9 x 355.6 mm

(8.5 x 14 in.)

139.7 x 210 mm

(5.5 x 8.27 in.)

215.9 x 355.6 mm

(8.5 x 14 in.)

Multipurpose

feeder*

148 x 210 mm

(5.83 x 8.27 in.)

215.9 x 355.6 mm

(8.5 x 14 in.)

69.85 x 127 mm

(2.75 x 5 in.)

229 x 355.6 mm

(9.01 x 14 in.)

* If you load paper that is narrower than 148 mm (5.83 in.) in the multipurpose feeder (for example, 3 x 5‑inch index cards),

set the MP Feeder Size menu item to Universal.

Labels Thickness: 0.102–0.305 mm (0.004–0.012 in.)

Smoothness: 100–400* Sheffield

* 150–250 Sheffield is optimal. Using media higher than 300 Sheffield could result in printing degradation.

Card stock Weight:

Up to 199 g/m

Index Bristol (90 lb)

Up to 203 g/m

Tag (100 lb)

Printer specifications 95

Standard trays and special media trays

The Lexmark T630, T632, and T634 paper feeding mechanism uses advanced technology that enhances feeding

reliability. The standard Lexmark T630, T632, and T634 tray, which holds 250 or 500 sheets of bond paper, reliably feeds

all media tested according to the guidelines specified under

“Dimensions” on page 9.

For those difficult‑to‑print sizes, such as 3 x 5‑inch index cards, Lexmark offers a variety of special media trays and

drawers.

Note: Optional 250‑sheet Universally Adjustable Trays can be used to print forms with a minimum length of 5 inches

using a T630 when installed either in the integral tray location or in a 250‑sheet drawer under a 250‑sheet integral

tray. Optional 250‑sheet Universally Adjustable Trays support forms with a minimum length of 7 inches on a T632.

Optional 400‑sheet Universally Adjustable Trays support forms with a minimum length of 7 inches on the T630, T632

and T634.

Source Part number

250‑Sheet Special Media Tray 11K1572

250‑Sheet Special Media Drawer 11K1573

250‑Sheet Universally Adjustable Tray 11K1574

250‑Sheet Universally Adjustable Drawer 11K1878

500‑Sheet Special Media Tray 11K1921

500‑Sheet Special Media Tray + Drawer 11K1922

400‑Sheet Universally Adjustable Tray 11K1941

400‑Sheet Universally Adjustable Tray + Drawer 11K1942

Card stock and label guidelines

Labels are one of the most difficult print materials for laser printers. A special fuser cleaner should be used for label

applications to optimize feed reliability. See your printer documentation for information on ordering label fuser

cleaners.

Printing labels on the T630, T632 and T634 requires a special label fuser cleaner that prevents duplexing.

It is recommended that when you run vinyl labels, you install a special oil fuser cleaner, P/N 56P1415. When you order

a new cartridge, be sure to order the cartridge that will include the correct fuser cleaner.

It is possible to duplex certain labels that have been specifically designed for this application. To duplex labels, consult

the Lexmark “Converter Lists” to see which converters have successfully developed this type of label, and you must

install a special fuser wiper. The wax wiper that is used with the T630, T632, and T634 is P/N 56P2109. (Cartridges

designed for duplex label printing contain two wax wipers. Change the wax wiper at the halfway point of your normal

cartridge usage to provide additional cleaning and optimize performance.)

When printing on labels:

• Using the printer operator panel, set the Paper Type to Labels in the Paper Menu. For vinyl and other heavy labels,

set the Labels Weight (under the Paper Weight menu) to Heavy, and set the Labels Texture (under the Paper Texture

menu) to Smooth.

Note: When Paper Type is set to Labels, and Labels Weight is set to Heavy, the printer reduces the printing

speed to 30 ppm, to ensure acceptable printing.

• Do not load labels together with paper or transparencies in the same paper tray. Combining print materials can

cause feeding problems.

Printer specifications 96

• Use full label sheets. Partial sheets may cause labels to peel off during printing, resulting in a paper jam. Adhesive

material may contaminate your printer. It could also void your printer and cartridge warranties.

When feeding labels, the number of labels per sheet can affect registration more than basis weight. Typically, the more

labels per sheet, the better the registration.

When printing on card stock:

• Set the Paper Type to Card Stock in the Paper Menu.

• Do not use card stock that is creased. It may cause paper jams.

For more information, see the following:

• “Pick roller technology” on page 11

• “Grain orientation” on page 17

• “Maintenance procedures” on page 14

• “Troubleshooting” on page 14

Lexmark T640, T642, T644

The Lexmark T640, T642, and T644 print on many labels designed for use with laser printers.

The following table lists the maximum weights supported by the trays and the multipurpose feeder.

Paper source

Grain

direction

Card stock Labels

Index

Bristol

Tag Cover Paper

Dual‑web

paper

Polyester Vinyl

Integrated tray grain long

grain short

163 g/m

199 g/m

163 g/m

203 g/m

176 g/m

216 g/m

180 g/m

220 g/m

300 g/m

Optional

250‑sheet

drawer

grain long

grain short

120 g/m

163 g/m

120 g/m

163 g/m

135 g/m

176 g/m

163 g/m

220 g/m

260 g/m

Optional

500‑sheet

drawer

grain long

grain short

163 g/m

199 g/m

163 g/m

203 g/m

176 g/m

216 g/m

180 g/m

220 g/m

300 g/m

Multipurpose

feeder*

grain long

grain short

120 g/m

163 g/m

120 g/m

163 g/m

135 g/m

176 g/m

163 g/m

220 g/m

260 g/m

* Due to label design characteristics, unacceptable feeding may be experienced from the multipurpose feeder.

Printer specifications 97

Labels Thickness: 0.102–0.305 mm (0.004–0.012 in.)

Smoothness: 100–400* Sheffield

* 150–250 Sheffield is optimal. Using media higher than 300 Sheffield could result in printing degradation.

Card stock Weight:

Up to 199 g/m

Index Bristol (90 lb)

Up to 203 g/m

Tag (100 lb)

Standard trays and special trays

The Lexmark T640, T642, and T644 paper feeding mechanism uses advanced technology that enhances feeding

reliability. The standard Lexmark T640, T642, and T644 tray holds 250 or 500 sheets of bond paper and reliably feeds

all media tested according to the guidelines specified under

“Dimensions” on page 9.

For those difficult‑to‑print sizes, such as 3 x 5‑inch index cards, Lexmark offers a variety of special media trays and

drawers.

Note: Optional 250‑sheet Universally Adjustable Trays can be used to print forms with a minimum length of 5 inches

when installed either in the integral tray location or in a 250‑sheet drawer under a 250‑sheet integral tray. Forms

less than 7 inches long are not supported from a 400‑sheet universally adjustable tray.

Source Part number

250‑Sheet Mild Special Media Tray 20G1237

250‑Sheet Aggressive Special Media Tray 20G1230

250‑Sheet Mild Special Media Drawer 20G1236

250‑Sheet Aggressive Special Media Drawer 20G1229

250‑Sheet Universally Adjustable Tray 20G1224

250‑Sheet Universally Adjustable Drawer 20G1223

500‑Sheet Mild Special Media Tray 20G1240

500‑Sheet Mild Special Media Tray + Drawer 20G1239

500‑Sheet Aggressive Special Media Tray 20G1227

500‑Sheet Aggressive Special Media Tray + Drawer 20G1226

400‑Sheet Universally Adjustable Tray 20G1217

400‑Sheet Universally Adjustable Tray + Drawer 20G1218

Card stock and label guidelines

Labels are one of the most difficult print materials for laser printers. A special fuser cleaner should be used for label

applications to optimize feed reliability. See your printer documentation for information on ordering additional label

fuser cleaners.

Printing labels on the T640, T642, and T644 requires a special label fuser cleaner that prevents duplexing.

It is recommended that when you run vinyl labels, you install a special oil fuser cleaner, P/N 40X2665. When you order

a new cartridge, be sure to order the cartridge that will include the correct fuser cleaner.

Printer specifications 98

It is possible to duplex certain labels that have been specifically designed for this application. To duplex labels, consult

the Lexmark "Converter Lists" to see which converters have successfully developed this type of label, and you must

install a special fuser wiper. The wax wiper that is used with the T640, T642, and T644 is P/N 40X2666. (Cartridges

designed for duplex label printing contain two wax wipers. Change the wax wiper at the halfway point of your normal

cartridge usage to provide additional cleaning and optimize performance.)

When printing on labels:

• Set the Paper Type to Labels in the Paper Menu. For vinyl and other heavy labels, set the Paper Type to Vinyl Labels.

Note: When Paper Type is set to Vinyl Labels, the printer reduces the printing speed to ensure acceptable

printing.

• Do not load labels together with paper or transparencies in the same paper tray. Combining print materials can

cause feeding problems.

• Use full label sheets. Partial sheets may cause labels to peel off during printing, resulting in a paper jam. Adhesive

material may contaminate your printer. It could also void your printer and cartridge warranties.

When feeding labels, the number of labels per sheet can affect registration more than basis weight. Typically, the more

labels per sheet, the better the registration.

When printing on card stock:

• Set the Paper Type to Card Stock in the Paper Menu.

• Do not use card stock that is creased. It may cause paper jams.

For more information, see the following:

• “Pick roller technology” on page 11

• “Grain orientation” on page 17

• “Maintenance procedures” on page 14

• “Troubleshooting” on page 14

Lexmark T650, T652, T654, and T656dne

The Lexmark T650, T652, T654, and T656dne print on many labels designed for use with laser printers.

The following table lists the maximum weights supported by the trays and the multipurpose feeder.

Printer specifications 99

Paper source

Grain

direction

Card stock Labels

Index

Bristol

Tag Cover Paper

Dual‑web

paper

Polyester Vinyl

Integrated tray grain long

grain short

163 g/m

199 g/m

163 g/m

203 g/m

176 g/m

216 g/m

180 g/m

220 g/m

300 g/m

Optional

250‑sheet

drawer

grain long

grain short

120 g/m

163 g/m

120 g/m

163 g/m

135 g/m

176 g/m

163 g/m

220 g/m

260 g/m

Optional

550‑sheet

drawer

grain long

grain short

163 g/m

199 g/m

163 g/m

203 g/m

176 g/m

216 g/m

180 g/m

220 g/m

300 g/m

Multipurpose

feeder*

grain long

grain short

120 g/m

163 g/m

120 g/m

163 g/m

135 g/m

176 g/m

163 g/m

220 g/m

260 g/m

* Due to label design characteristics, unacceptable feeding may be experienced from the multipurpose feeder.

Labels Thickness: 0.102–0.305 mm (0.004–0.012 in.)

Smoothness: 100–400* Sheffield

*150–250 Sheffield is optimal. Using media higher than 300 Sheffield could result in printing degradation.

Card stock Weight:

Up to 199 g/m

Index Bristol (90 lb)

Up to 203 g/m

Tag (100 lb)

Up to 216 g/m

Cover (80 lb)

Standard trays and special trays

The Lexmark T650, T652, T654, and T656dne paper feeding mechanism uses advanced technology that enhances

feeding reliability. The standard Lexmark T650, T652, T654, and T656dne tray holds 250 and 550 sheets of bond paper

and reliably feeds all media tested according to the guidelines specified under

“Dimensions” on page 9.

For difficult‑to‑print sizes, such as 3 x 5‑inch index cards, Lexmark offers a variety of special media trays and drawers.

Note: Optional 200‑sheet Universally Adjustable Trays can be used to print forms with a minimum length of

five inches when installed either in the integral tray location or in a 200‑sheet drawer under a 200‑sheet integral

tray. Forms less than seven inches long are not supported from a 400‑sheet universally adjustable tray.

Source Part number

200‑Sheet Aggressive Special Media Tray 30G0932

200‑Sheet Aggressive Special Media Tray + Drawer 30G0933

200‑Sheet Lockable Universally Adjustable Tray + Drawer 30G0836

200‑Sheet Mild Special Media Tray 30G0890

200‑Sheet Mild Special Media Tray + Drawer 30G0891

200‑Sheet Universally Adjustable Tray 30G0872

200‑Sheet Universally Adjustable Tray + Drawer 30G0871

400‑Sheet Lockable Universally Adjustable Tray + Drawer 30G0859

Printer specifications 100

Source Part number

400‑Sheet Mild Special Media Tray 30G0934

400‑Sheet Mild Special Media Tray + Drawer 30G0935

400‑Sheet Aggressive Special Media Tray 30G0892

400‑Sheet Aggressive Special Media Tray + Drawer 30G0893

400‑Sheet Universally Adjustable Tray 30G0861

400‑Sheet Universally Adjustable Tray + Drawer 30G0860

550‑Sheet Lockable Tray + Drawer 30G0849

Card stock and label guidelines

Labels are one of the most difficult print materials for laser printers. A special fuser cleaner should be used for label

applications to optimize feed reliability. See your printer documentation for information on ordering additional label

fuser cleaners.

Printing labels on the T650, T652, T654, and T656dne requires a special label fuser cleaner that prevents duplexing.

It is recommended that when you run labels, you install a special oil fuser cleaner, P/N 40X2665. When you order a

new cartridge, be sure to order the cartridge that will include the correct fuser cleaner.

It is possible to duplex certain labels that have been specifically designed for this application. To duplex labels, consult

the Lexmark "Converter Lists" to see which converters have successfully developed this type of label, and you must

install a special fuser wiper. The wax wiper that is used with the T650, T652, T654, and T656dne is P/N 40X2666.

(Cartridges designed for duplex label printing contain two wax wipers. Change the wax wiper at the halfway point of

your normal cartridge usage to provide additional cleaning and optimize performance.). Contact your Supplies and

Label Specialist for information on oil and wax vinyl label cartridges.

Note: Wax wipers are not recommended when using vinyl labels.

When printing on labels:

• Set the Paper Type to Labels in the Paper Menu. For vinyl and other heavy labels, set the Paper Type to Vinyl Labels.

Note: When Paper Type is set to Vinyl Labels, the printer reduces the printing speed to ensure acceptable

printing.

• Do not load labels together with paper or transparencies in the same paper tray. Combining print materials can

cause feeding problems.

• Use full label sheets. Partial sheets may cause labels to peel off during printing, resulting in a paper jam. Adhesive

material may contaminate your printer. It could also void your printer and cartridge warranties.

When feeding labels, the number of labels per sheet can affect registration more than basis weight. Typically, the more

labels per sheet, the better the registration.

When printing on card stock:

• Set the Paper Type to Card Stock in the Paper Menu.

• Do not use card stock that is creased. It may cause paper jams.

For more information, see the following:

• “Pick roller technology” on page 11

• “Grain orientation” on page 17

Printer specifications 101

• “Maintenance procedures” on page 14

• “Troubleshooting” on page 14

Lexmark W812

The Lexmark W812 prints on many labels designed for use with laser printers.

The following table lists the maximum weights supported by the trays and the multipurpose feeder.

Paper source

Card stock Labels

Index Bristol Tag Cover Paper Vinyl

250‑sheet Tray 1* — — — — —

Multipurpose feeder

111 g/m

123 g/m

74 g/m

200 g/m

—

250 sheet option

111 g/m

123 g/m

74 g/m

200 g/m

—

500 sheet option* — — — — —

* The standard 250‑sheet tray (Tray 1) and 500‑sheet option do not support card stock or labels.

For paper and transparency specifications, see the publication CD that came with your printer.

Labels Width–Multipurpose

feeder:

87–297 mm (3.43–11.69 in.)

Length–Multipurpose

feeder:

98–508 mm (3.86–20 in.)

Width & Length–Optional

250‑sheet trays:

Standard sizes: A3, A4, A5, JIS B4, JIS B5, letter, legal, 8.5 x 13, 11 x 17

Weight:

64–200 g/m

Thickness: 0.13–0.20 mm (0.005–0.008 in.)

Smoothness: 100–400 Sheffield*

* 150–250 Sheffield is optimal. Using media higher than 300 Sheffield could result in printing degradation.

Card stock Width: 210–216 mm (8.3–8.5 in.)

Length: 279–356 mm (11–11.7 in.)

Weight:

Up to 163 g/m

Printer specifications 102

Lexmark W820

Limit label printing to occasional use of A4‑ or letter‑size paper office labels designed for laser printers. We do not

recommend using vinyl or polyester labels.

The Lexmark W820 supports stocks up to 163 g/m

. Always feed labels and card stock from Tray 1, 2, or 3, each of

which can hold up to 250 sheets of labels or card stock.

The following table lists the maximum weights supported by the trays and the multipurpose feeder.

Paper source Media types Weight

Tray 1 Paper, Bond, Card stock, Labels, Transparencies

60–163 g/m

Trays 2, 3 Paper, Bond, Card stock, Labels

60–163 g/m

Trays 4, 5 Paper, Bond

60–105 g/m

Multipurpose Feeder Paper, Bond, Card stock, Labels, Transparencies, Envelopes

120–128 g/m

For paper and transparency specifications, see the printer publications CD.

Labels Width: 210–216 mm (8.3–8.5 in.)

Length: 279–356 mm (11–11.7 in.)

Weight:

120–128 g/m

Thickness: 0.13–0.20 mm (0.005–0.008 in.)

Smoothness: 100–400 Sheffield*

* 150–250 Sheffield is optimal. Using media higher than 300 Sheffield could result in printing degradation.

Card stock Width: 210–216 mm (8.3–8.5 in.)

Length: 279–356 mm (11–11.7 in.)

Weight:

Up to 163 g/m

Card stock and label guidelines

When printing on labels:

• Set the Paper Type to Labels in the Paper Menu.

• Do not use label sheets with a slick backing material.

• Do not print within 1 mm (0.04 in.) of the die-cut, the edge of the label or the perforations, or between the die-

cuts.

Printer specifications 103

• Use full label sheets. Partial sheets may cause labels to peel off during printing, resulting in a paper jam.

• Do not use label sheets that have adhesive to the edge of the sheet. We recommend zone coating of the adhesive

at least 1 mm (0.04 in.) away from the edges. Adhesive material may contaminate your printer and could void your

warranty.

When printing on card stock:

• Set the Paper Type to Card Stock.

• Do not use card stock that is creased. It may cause paper jams.

• We recommend the use of grain long card stock.

Lexmark W840

Limit label printing to occasional use of A4‑ or letter‑size paper office labels designed for laser printers. We do not

recommend using vinyl or polyester labels.

The Lexmark W840 supports stocks up to 216 g/m

. Always feed labels and card stock from Tray 1, 2, or the multipurpose

feeder.

The following table lists the maximum weights supported by the trays and the multipurpose feeder.

Tray 1 Tray 2 Multipurpose feeder

Labels

64–105 g/m

64–216 g/m

Card stock

64–105 g/m

64–216 g/m

Labels Width: 89–297 mm (3.5–11.7 in.)

Length: 99–432 mm (3.9–17 in.)

Weight:

64–216 g/m

Thickness: Up to 0.25 mm

Smoothness: 100–400 Sheffield*

* 150–250 Sheffield is optimal. Using media higher than 300 Sheffield could result in printing degradation.

Card stock Width: 89–297 mm (3.5–11.7 in.)

Length: 99–432 mm (3.9–17 in.)

Weight:

Up to 216 g/m

Printer specifications 104

Card stock and label guidelines

When printing on labels:

• Set the Paper Type to Labels from the printer driver.

• Use standard‑size products (either A4 or Letter).

• Do not use label sheets with a slick backing material.

• Do not print within 1 mm (0.040 in.) of the die-cut.

• Use full label sheets. Partial sheets may cause labels to peel off during printing, resulting in a paper jam. Partial

sheets will also contaminate your printer and your cartridge with adhesive, and could void your printer and cartridge

warranties.

• Use labels that can withstand temperatures of 180°C (356°F) without sealing, excessive curling, wrinkling, or

releasing hazardous emissions.

• Verify that your label adhesive material can tolerate a fusing temperature of 180°C (356°F) for 0.1 second.

• Use labels that can withstand pressure of 25 pounds per square inch (psi).

• Do not print within 1 mm (0.040 in.) of the edge of the label, of the perforations, or between die-cuts of the label.

• Do not use label sheets that have adhesive to the edge of the sheet. We recommend zone coating of the adhesive

at least 1 mm (0.040 in.) away from edges. Adhesive material will contaminate your printer and could void your

warranty.

• If zone coating of the adhesive is not possible, a 3‑mm (0.125‑in.) strip should be removed on the leading and driver

edge, and a non‑oozing adhesive should be used.

• Remove a 3‑mm (0.125‑in.) strip from the leading edge to prevent labels from peeling inside the printer.

• Portrait orientation is preferred, especially when printing bar codes.

• Do not use labels that have exposed adhesive.

• Do not use labels that are separating from the backing sheet or are wrinkled, bubbled, or otherwise damaged.

• Do not load a sheet of labels through the machine more than once.

• Load labels into the manual bypass feeder with the recommended print side faceup and the top edge going in first.

When printing on card stock:

• Set the Paper Type to Card Stock from the printer driver.

• Do not use preprinted card stock manufactured with chemicals that may contaminate the printer. Preprinting

introduces semi‑liquid and volatile components into the printer.

• Do not use card stock that is creased. It may cause paper jams.

• We recommend the use of grain short card stock.

• Load card stock into the manual bypass feeder with the recommended print side faceup and the top edge going in

first.

Printer specifications 105

Lexmark W850

Limit label printing to occasional use of A4‑ or letter‑size paper office labels designed for laser printers. We do not

recommend using vinyl or polyester labels.

The Lexmark W850 supports stocks up to 216 g/m

. Always feed labels and card stock from Tray 1, 2 or the multipurpose

feeder.

The following table lists the maximum weights supported by the trays and the multipurpose feeder.

Paper source Media types Weight

Tray 1 Paper, Labels, Transparencies

64‑105 g/m

Tray 2 Paper, Card stock, Labels, Transparencies

64‑216 g/m

Multipurpose feeder Paper, Card stock, Envelopes, Labels, Transparencies

64‑216 g/m

Labels Width: 89–297 mm (3.5–11.7 in.)

Length: 99–432 mm (3.9–17 in.)

Weight:

64‑216 g/m

Thickness: Up to 0.25 mm

Smoothness: 100–400 Sheffield*

* 150–250 Sheffield is optimal. Using media higher than 300 Sheffield could result in printing degradation.

Card stock Width: 89–297 mm (3.5–11.7 in.)

Length: 99–432 mm (3.9–17 in.)

Weight:

Up to 216 g/m

Card stock and label guidelines

When printing on labels:

• Set the Paper Type to Labels from the printer driver.

• Use standard‑size products (either A4 or Letter).

• Do not use label sheets with a slick backing material.

• Do not print within 1 mm (0.040 in.) of the die-cut.

• Use full label sheets. Partial sheets may cause labels to peel off during printing, resulting in a paper jam. Partial

sheets will also contaminate your printer and your cartridge with adhesive, and could void your printer and cartridge

warranties.

Printer specifications 106

• Use labels that can withstand temperatures of 180°C (356°F) without sealing, excessive curling, wrinkling, or

releasing hazardous emissions.

• Verify that your label adhesive material can tolerate a fusing temperature of 180°C (356°F) for 0.1 second.

• Use labels that can withstand pressure of 25 pounds per square inch (psi).

• Do not print within 1 mm (0.040 in.) of the edge of the label, of the perforations, or between die-cuts of the label.

• Do not use label sheets that have adhesive to the edge of the sheet. We recommend zone coating of the adhesive

at least 1 mm (0.040 in.) away from edges. Adhesive material will contaminate your printer and could void your

warranty.

• If zone coating of the adhesive is not possible, a 3‑mm (0.125‑in.) strip should be removed on the leading and driver

edge, and a non‑oozing adhesive should be used.

• Remove a 3‑mm (0.125‑in.) strip from the leading edge to prevent labels from peeling inside the printer.

• Portrait orientation is preferred, especially when printing bar codes.

• Do not use labels that have exposed adhesive.

• Do not use labels that are separating from the backing sheet or are wrinkled, bubbled, or otherwise damaged.

• Do not load a sheet of labels through the machine more than once.

• Load labels into the manual bypass feeder with the recommended print side faceup and the top edge going in first.

When printing on card stock:

• Set the Paper Type to Card Stock from the printer driver.

• Do not use preprinted card stock manufactured with chemicals that may contaminate the printer. Preprinting

introduces semi‑liquid and volatile components into the printer.

• Do not use card stock that is creased. It may cause paper jams.

• We recommend the use of grain short card stock.

• Load card stock into the manual bypass feeder with the recommended print side faceup and the top edge going in

first.

Lexmark X203n and X204n

Limit label printing to occasional use of paper office labels designed for laser printers. We do not recommend printing

more than 20 pages of labels a month. For best results, feed labels from the paper tray.

The Lexmark X203n and X204n printer models support stocks up to 90 g/m

(24 lb).

Printer specifications 107

Note: The smallest supported Universal size is 76 x 127 mm (3 x 5 in.); the largest is 216 x 356 mm (8.5 x 14 in.).

The following table lists the maximum weights supported by the paper tray and the manual feeder.

Paper source

Card stock Labels

Index Bristol Tag Cover Paper

Paper tray

163 g/m

—

163 g/m

Manual feeder

163 g/m

—

163 g/m

Note: The manual feeder can feed only one sheet at a time.

Labels Width: 210–216 mm (8.3–8.5 in.)

Length: 216–356 mm (8.5–14 in.)

Weight:

Up to 163 g/m

(43 lb)

Thickness: Up to 0.25 mm (0.01 in.)

Smoothness: 100–300* Sheffield

* 150–200 Sheffield is optimal. Using media higher than 300 Sheffield could result in printing degradation.

Card stock Weight:

Up to 163 g/m

Index Bristol (90 lb)

Up to 163 g/m

Tag (100 lb)

When printing on labels:

• Use labels only in the paper tray or manual feeder. Do not use labels in the ADF.

• Do not use labels with slick backing material.

• Use full label sheets. Partial sheets may cause labels to peel off during printing, resulting in a jam. Partial sheets

also contaminate the printer and the cartridge with adhesive, and could void the printer and cartridge warranties.

• Do not use labels with exposed adhesive.

• Use labels designed specifically for laser printers. Check with the manufacturer or vendor to verify that the labels

can withstand temperatures up to 225°C (437°F) without sealing, excessive curling, wrinkling, or releasing hazardous

emissions.

• Do not print within 1 mm (0.04 in.) of the edge of the label, of the perforations, or between die-cuts of the label.

• Portrait orientation works best, especially when printing bar codes.

• Be sure adhesive backing does not reach to the sheet edge. Zone coating of the adhesive at least 1 mm (0.04 in.)

away from edges is recommended. Adhesive material contaminates the printer and could void the warranty. If zone

coating of the adhesive is not possible, remove a 1.6 mm (0.06 in.) strip on the leading and driver edge, and use a

non‑oozing adhesive.

When printing on card stock:

• Make sure the Paper Type is Card Stock.

• Select the appropriate Paper Texture setting.

• Be aware that preprinting, perforation, and creasing may significantly affect the print quality and cause jams or

other paper handling problems.

• Check with the manufacturer or vendor to ensure the card stock can withstand temperatures up to 210°C (410°F)

without releasing hazardous emissions.

Printer specifications 108

• Do not use preprinted card stock manufactured with chemicals that may contaminate the printer. Preprinting

introduces semi-liquid and volatile components into the printer.

• Use grain short card stock when possible.

Note: To minimize curl, us the rear exit when printing on card stock and labels.

For more information, see

“Maintenance procedures” on page 14.

Lexmark X215

The Lexmark X215 prints on paper office labels designed for use with laser printers.

Labels can be fed only from the manual bypass feeder. Card stock and labels must be fed one sheet at a time through

the manual bypass feeder.

The following table lists the maximum weights supported by the manual bypass feeder.

Paper source

Card stock

Index Bristol Tag Cover

Manual bypass feeder*

Up to 163 g/m

(90 lb) Up to 163 g/m

(100 lb)

—

* Card stock can be fed only from the manual bypass feeder.

For paper and transparency specifications, see the Lexmark X215 User's Guide.

Labels Width: 210–216 mm (8.3–8.5 in.)

Length: 279–297 mm (11–11.7 in.)

Weight:

Up to 163 g/m

(43 lb bond)

Thickness: Up to 0.25 mm (0.01 in.)

Smoothness: 100–400* Sheffield

* 150–250 Sheffield is optimal. Using media higher than 300 Sheffield could result in printing degradation.

Card stock Weight:

Up to 163 g/m

Index Bristol (90 lb)

Up to 163 g/m

Tag (100 lb)

Card stock and label guidelines

Use only materials recommended for use with laser printers.

Printer specifications 109

To prevent specialty media sheets from sticking together, remove each sheet from the output bin as it is printed.

When printing on labels:

• Set the Paper Type to Labels from the printer driver.

• Use standard‑size products (either A4 or Letter).

• Do not use label sheets with a slick backing material.

• Do not print within 1 mm (0.040 in.) of the die-cut.

• Use full label sheets. Partial sheets may cause labels to peel off during printing, resulting in a paper jam. Partial

sheets will also contaminate your printer and your cartridge with adhesive, and could void your printer and cartridge

warranties.

• Use labels that can withstand temperatures of 180°C (356°F) without sealing, excessive curling, wrinkling, or

releasing hazardous emissions.

• Verify that your label adhesive material can tolerate a fusing temperature of 180°C (356°F) for 0.1 second.

• Use labels that can withstand pressure of 25 pounds per square inch (psi).

• Do not print within 1 mm (0.040 in.) of the edge of the label, of the perforations, or between die-cuts of the label.

• Do not use label sheets that have adhesive to the edge of the sheet. We recommend zone coating of the adhesive

at least 1 mm (0.040 in.) away from edges. Adhesive material will contaminate your printer and could void your

warranty.

• If zone coating of the adhesive is not possible, a 3‑mm (0.125‑in.) strip should be removed on the leading and driver

edge, and a non‑oozing adhesive should be used.

• Remove a 3‑mm (0.125‑in.) strip from the leading edge to prevent labels from peeling inside the printer.

• Portrait orientation is preferred, especially when printing bar codes.

• Do not use labels that have exposed adhesive.

• Do not use labels that are separating from the backing sheet or are wrinkled, bubbled, or otherwise damaged.

• Do not load a sheet of labels through the machine more than once.

• Load labels into the manual bypass feeder with the recommended print side faceup and the top edge going in first.

When printing on card stock:

• Set the Paper Type to Card Stock from the printer driver.

• Do not use preprinted card stock manufactured with chemicals that may contaminate the printer. Preprinting

introduces semi‑liquid and volatile components into the printer.

• Do not use card stock that is creased. It may cause paper jams.

• We recommend the use of grain short card stock.

• Load card stock into the manual bypass feeder with the recommended print side faceup and the top edge going in

first.

Printer specifications 110

Lexmark X264dn, X363dn, X364dn, and X364dw

Limit label printing to occasional use of paper office labels designed for laser printers. We do not recommend using

vinyl, pharmacy, or polyester labels. It is recommended to print no more than 20 pages of paper labels a month.

The printer and duplex path support paper and label stock from 60–90 g/m

(16‑24 lb). The multipurpose and manual

feeders support card stock up to 163 g/m

(43 lb). You can load up to 50 label sheets in the standard tray. Card stock

must be sent through the manual feeder one sheet at a time.

The following table lists the maximum weights supported by the standard tray, optional 250‑ and 550‑sheet trays, and

multipurpose and manual feeders.

Paper source

Card Stock Labels

Index Bristol Tag Cover Paper

Standard tray — — —

90 g/m

Optional 250‑sheet tray

Optional 550‑sheet tray

———

90 g/m

Manual feeder

Multipurpose feeder

163 g/m

—

90 g/m

Card stock should be grain short and set to exit the rear door.

For paper and transparency specifications, see the printer publications CD.

Labels Width: 210–216 mm (8.3–8.5 in.)

Length: 279–297 mm (11–11.7 in.)

Weight:

Up to 90 g/m

(24 lb)

Thickness: Up to 0.25 mm (0.01 in.)

Smoothness: 100–300* Sheffield

*150–200 Sheffield is optimal. Using media higher than 300 Sheffield could result in printing degradation.

Card stock Weight:

Up to 163 g/m

Index Bristol (90 lb)

Up to 163 g/m

Tag (100 lb)

Note: To minimize curl, use the rear exit when printing on card stock and labels.

Printer specifications 111

When printing on labels:

• Check with the manufacturer or vendor to ensure the labels can withstand temperatures up to 210°C (410°F) without

sealing, curling excessively, wrinkling, or releasing hazardous emissions.

• Check with the manufacturer or vendor to ensure the labels can withstand 25 psi (172 kPa) pressure without

delaminating, oozing around the edges, or releasing hazardous fumes.

• Do not use labels with slick backing material.

• Use full label sheets. Partial sheets may cause labels to peel off during printing, resulting in a jam.

• Do not use labels with exposed adhesive.

• Do not print within 1 mm (0.04 in.) of the edge of the label, of the perforations, or between die‑cuts on the label.

• Be sure adhesive backing does not reach to the sheet edge. Zone coating of the adhesive at least 1 mm (0.04 in.)

away from the edges is recommended. Adhesive material contaminates the printer and could void the warranty.

• If zone coating of the adhesive is not possible, remove a 1.6 mm (0.06 in.) strip on the leading and driver edge, and

use a non‑oozing adhesive.

• Portrait orientation works best, especially when printing bar codes.

When printing on card stock:

• Make sure the Paper Type is Card Stock.

• Select the Paper Texture setting.

• Be aware that preprinting, perforation, and creasing may significantly affect the print quality and cause jams or

other paper handling problems.

• Check with the manufacturer or vendor to ensure the card stock can withstand temperatures up to 210°C (410°F)

without releasing hazardous emissions.

• Do not use preprinted card stock manufacturer with chemicals that may contaminate the printer.

• Use grain short card stock when possible.

For more information, see

“Maintenance procedures” on page 14.

Lexmark X422

The Lexmark X422 prints on many labels designed for use with laser printers.

Card stock is supported from the multipurpose feeder, and labels are supported from the standard tray.

The following table lists the maximum weights supported.

Note: Scanning large quantities of labels is not recommended.

Printer specifications 112

Paper source Card stock Paper labels

Tray 1 (standard) —

60–90 g/m

Multipurpose feeder

60–199 g/m

—

Card stock and label guidelines

Use only materials recommended for use with laser printers.

To prevent specialty media sheets from sticking together, remove each sheet from the output bin as it is printed.

When printing on labels:

• Set the Paper Type to Labels from the printer driver.

• Use standard‑size products (either A4 or Letter).

• Do not use label sheets with a slick backing material.

• Do not print within 1 mm (0.040 in.) of the die-cut.

• Use full label sheets. Partial sheets may cause labels to peel off during printing, resulting in a paper jam. Partial

sheets will also contaminate your printer and your cartridge with adhesive, and could void your printer and cartridge

warranties.

• Use labels that can withstand temperatures of 180°C (356°F) without sealing, excessive curling, wrinkling, or

releasing hazardous emissions.

• Verify that your label adhesive material can tolerate a fusing temperature of 180°C (356°F) for 0.1 second.

• Use labels that can withstand pressure of 25 pounds per square inch (psi).

• Do not print within 1 mm (0.040 in.) of the edge of the label, of the perforations, or between die-cuts of the label.

• Do not use label sheets that have adhesive to the edge of the sheet. We recommend zone coating of the adhesive

at least 1 mm (0.040 in.) away from edges. Adhesive material will contaminate your printer and could void your

warranty.

• If zone coating of the adhesive is not possible, a 3‑mm (0.125‑in.) strip should be removed on the leading and driver

edge, and a non‑oozing adhesive should be used.

• Remove a 3‑mm (0.125‑in.) strip from the leading edge to prevent labels from peeling inside the printer.

• Portrait orientation is preferred, especially when printing bar codes.

• Do not use labels that have exposed adhesive.

• Do not use labels that are separating from the backing sheet or are wrinkled, bubbled, or otherwise damaged.

• Do not load a sheet of labels through the machine more than once.

• Load labels into the standard tray with the recommended print side faceup and the top edge going in first.

When printing on card stock:

• Set the Paper Type to Card Stock from the printer driver.

• Do not use preprinted card stock manufactured with chemicals that may contaminate the printer. Preprinting

introduces semi‑liquid and volatile components into the printer.

• Do not use card stock that is creased. It may cause paper jams.

• We recommend the use of grain short card stock.

• Load card stock into the multipurpose feeder with the recommended print side faceup and the top edge going in

first.

Printer specifications 113

Lexmark X463de, X464de, X466dte, and X466dtwe

Limit label printing to occasional use of paper office labels designed for laser printers. We do not recommend using

vinyl, pharmacy, or polyester labels. It is recommended to print no more than 20 pages of paper labels a month.

The printer and duplex path support 60–90 g/m

(16–24 lb) paper weights. The multipurpose feeder supports 60–

163 g/m

(16–43 lb) paper weights. You can load up to 50 label sheets in the standard tray and optional trays. You can

load up to 15 paper labels and up to 10 sheets of card stock in the multipurpose feeder.

The following table lists the maximum weights supported by the standard tray, optional 250‑ and 550‑sheet trays, and

multipurpose and manual feeders.

Paper source

Card Stock Labels

Index Bristol Tag Cover Paper

Standard tray — — —

90 g/m

Optional 250‑sheet tray

Optional 550‑sheet tray

———

90 g/m

Manual feeder

Multipurpose feeder

163 g/m

—

90 g/m

Card stock should be grain short and set to exit the rear door.

For paper and transparency specifications, see the printer publications CD.

Labels Width: 210–216 mm (8.3–8.5 in.)

Length: 279–297 mm (11–11.7 in.)

Weight:

Up to 90 g/m

(24 lb)

Thickness: Up to 0.25 mm (0.01 in.)

Smoothness: 100–300* Sheffield

*150–200 Sheffield is optimal. Using media higher than 300 Sheffield could result in printing degradation.

Card stock Weight:

Up to 163 g/m

Index Bristol (90 lb)

Up to 163 g/m

Tag (100 lb)

Note: To minimize curl, use the rear exit when printing on card stock and labels.

Printer specifications 114

When printing on labels:

• Check with the manufacturer or vendor to ensure the labels can withstand temperatures up to 210°C (410°F) without

sealing, curling excessively, wrinkling, or releasing hazardous emissions.

• Check with the manufacturer or vendor to ensure the labels can withstand 25 psi (172 kPa) pressure without

delaminating, oozing around the edges, or releasing hazardous fumes.

• Do not use labels with slick backing material.

• Use full label sheets. Partial sheets may cause labels to peel off during printing, resulting in a jam.

• Do not use labels with exposed adhesive.

• Do not print within 1 mm (0.04 in.) of the edge of the label, of the perforations, or between die‑cuts on the label.

• Be sure adhesive backing does not reach to the sheet edge. Zone coating of the adhesive at least 1 mm (0.04 in.)

away from the edges is recommended. Adhesive material contaminates the printer and could void the warranty.

• If zone coating of the adhesive is not possible, remove a 1.6 mm (0.06 in.) strip on the leading and driver edge, and

use a non‑oozing adhesive.

• Portrait orientation works best, especially when printing bar codes.

When printing on card stock:

• Make sure the Paper Type is Card Stock.

• Select the Paper Texture setting.

• Be aware that preprinting, perforation, and creasing may significantly affect the print quality and cause jams or

other paper handling problems.

• Check with the manufacturer or vendor to ensure the card stock can withstand temperatures up to 210°C (410°F)

without releasing hazardous emissions.

• Do not use preprinted card stock manufactured with chemicals that may contaminate the printer.

• Use grain short card stock when possible.

For more information, see

“Maintenance procedures” on page 14.

Lexmark X500 and X502n

Limit label printing to occasional use of paper office labels designed for laser printers. The Lexmark X500 and X502n

do not support vinyl or polyester labels.

The Lexmark X500 and X502n support 90–210 g/m

(24–55 lb) stock. Card stock and labels are supported from Tray 1

and Tray 2.

Printer specifications 115

Tray 1 supports approximately 120 sheets of card stock and Tray 2 supports up to 250 sheets of card stock. The following

table lists the maximum weights supported.

Paper source

Card stock

Labels

Index Bristol Tag Cover Paper

Tray 1 (standard tray)

90–210 g/m

180 g/m

Tray 2 (optional tray)

90–210 g/m

180 g/m

Grain short is preferred for papers over 135 g/m

Vinyl labels are not supported.

Labels Width: 76.2–216 mm (3–8.5 in.)

Length: 123.8–355.6 mm (4.88–14 in.)

Weight:

180 g/m

(48 lb)

Thickness: 0.13–0.20 mm (0.005–0.008 in.)

Smoothness: 100–400 Sheffield*

* 150–250 Sheffield is optimal. Using media higher than 300 Sheffield could result in printing degradation.

Card Stock Weight:

163 g/m

Index Bristol (90 lb)

163 g/m

Tag (100 lb)

Cover Stock Weight:

Up to 210 g/m

For more information on the supported media sizes, see the printer User's Guide on the publications CD.

Lexmark X543, X544, and X546dtn

Limit label printing to occasional use of paper office labels designed for use with laser printers. Lexmark X543, X544,

and X546dtn do not support vinyl or polyester labels.

The following table lists the maximum weights supported by the trays and the multipurpose feeder.

Note: Scanning large quantities of labels is not recommended.

Printer specifications 116

Paper source Grain direction

Card stock Labels

Index Bristol Tag Cover Paper

Standard and optional

250‑sheet tray

grain long

grain short

120 g/m

163 g/m

120 g/m

163 g/m

135 g/m

176 g/m

131 g/m

Optional 550‑sheet

tray

grain long

grain short

120 g/m

163 g/m

120 g/m

163 g/m

135 g/m

176 g/m

131 g/m

Multipurpose feeder*

and manual slot

grain long

grain short

120 g/m

163 g/m

120 g/m

163 g/m

135 g/m

176 g/m

131 g/m

* The multipurpose feeder may not support labels with certain design characteristics.

Labels Thickness: 0.102–0.254 mm (0.004–0.010 in.)

Smoothness: 50–300 Sheffield*

* 50–150 Sheffield is optimal. This printer may support labels with smoothness of less than 50 Sheffield

such as coated paper, polyester, vinyl, or other synthetic facestock paper. Using media higher than 200

Sheffield could result in print quality degradation.

Card stock Weight:

Up to 163 g/m

Index Bristol (90 lb)

Up to 163 g/m

Tag (100 lb)

Up to 176 g/m

Cover (65 lb)

Card stock and label guidelines

When printing on labels:

• From the printer control panel, set Paper Type to Labels in the Paper Menu.

• Do not load labels together with paper or transparencies in the same paper tray. Combining print materials can

cause feeding problems.

• Use only letter-, A4-, or legal-size full label sheets. Partial sheets may cause labels to peel off during printing, resulting

in a paper jam. Adhesive material may contaminate your printer. It could also void your printer and cartridge

warranties.

When printing on card stock:

• From the printer control panel, set Paper Type to Card Stock in the Paper Menu.

• Set Paper Weight to Card Stock Weight in the Paper Menu.

• Set Card Stock Weight to Normal or Heavy.

• Do not use creased card stock. It may cause paper jams.

Printer specifications 117

Lexmark X548

Limit label printing to occasional use of paper office labels designed for use with laser printers. Lexmark X548 does not

support vinyl or polyester labels.

Note: Printing large quantities of labels is not recommended.

Paper source Grain direction

Card stock Labels

Index Bristol Tag Cover Paper

Standard and optional

250‑sheet tray

grain long

grain short

120 g/m

163 g/m

120 g/m

163 g/m

135 g/m

176 g/m

131 g/m

Standard and optional

550‑sheet tray

grain long

grain short

120 g/m

163 g/m

120 g/m

163 g/m

135 g/m

176 g/m

131 g/m

Multipurpose feeder*

and manual slot

grain long

grain short

120 g/m

163 g/m

120 g/m

163 g/m

135 g/m

176 g/m

131 g/m

* The multipurpose feeder may not support labels with certain design characteristics.

Labels Thickness: 0.102–0.254 mm (0.004–0.010 in.)

Smoothness: 50–300 Sheffield*

* 50–150 Sheffield is optimal. This printer may support labels with smoothness of less than 50 Sheffield

such as coated paper, polyester, vinyl, or other synthetic facestock paper. Using media higher than 200

Sheffield could result in print quality degradation.

Card stock Weight:

Up to 163 g/m

Index Bristol (90 lb)

Up to 163 g/m

Tag (100 lb)

Up to 176 g/m

Cover (65 lb)

Card stock and label guidelines

When printing on labels:

• From the printer control panel, set the paper size, type, texture, and weight in the Paper menu to match the labels

loaded in the tray.

• Do not load labels together with other types of paper to avoid jams.

Printer specifications 118

• Use full label sheets. Partial sheets may cause labels to peel off during printing, resulting in a jam. Partial sheets

also contaminate the printer and the cartridge with adhesive, and could void the printer and toner cartridge

warranties.

When printing on card stock:

• From the printer control panel, set the paper size, type, texture, and weight in the Paper menu to match the card

stock loaded in the tray.

• Do not use creased card stock to avoid jams.

Lexmark X560

The Lexmark X560 prints on many labels designed for use with laser printers.

The following table lists the maximum weights supported by the trays and the multipurpose feeder.

Note: Scanning large quantities of labels is not recommended.

Paper source Grain direction

Card stock Labels

Index Bristol Tag Cover Paper

Integrated Tray 2 grain long

grain short

163 g/m

199 g/m

163 g/m

203 g/m

176 g/m

216 g/m

180 g/m

Optional 550‑sheet

tray (Tray 3)

grain long

grain short

163 g/m

199 g/m

163 g/m

203 g/m

176 g/m

216 g/m

180 g/m

Multipurpose feeder*

(Tray 1)

grain long

grain short

163 g/m

199 g/m

163 g/m

203 g/m

176 g/m

216 g/m

180 g/m

* Due to label design characteristics, unacceptable feeding may be experienced from the multipurpose feeder.

Labels Thickness: 0.102–0.305 mm (0.004–0.012 in.)

Smoothness: 30–50* Sheffield

Weight:

180 g/m

(48 lb bond)

Printer specifications 119

* Using media higher than 300 Sheffield could result in printing degradation.

Card stock Weight:

Up to 199 g/m

Index Bristol (110 lb)

Up to 203 g/m

Tag (125 lb)

Up to 216 g/m

Cover (80 lb)

Card stock and label guidelines

When printing on labels:

• From Print Properties or the printer control panel, set the Paper type to Labels.

• Do not load labels together with paper or transparencies in the same paper tray. Combining print materials can

cause feeding problems.

• Use only letter-, A4-, and legal-size label sheets.

• Use full label sheets. Partial sheets may cause labels to peel off during printing, resulting in a paper jam. Adhesive

material may contaminate your printer. It could also void your printer and cartridge warranties.

• Do not use vinyl labels.

When printing on card stock:

• From Print Properties or the printer control panel, set the Paper type to Thin Card Stock or Thick Card Stock.

• Do not use card stock that is creased. It may cause paper jams.

Lexmark X642e

The Lexmark X642e prints on many labels designed for use with laser printers.

The following table lists the maximum weights supported by the trays and the multipurpose feeder.

Note: Scanning large quantities of labels is not recommended.

Printer specifications 120

Paper source

Grain

direction

Card stock Labels

Index

Bristol

Tag Cover Paper

Dual‑web

paper

Polyester Vinyl

Integrated tray (grain long)

(grain short)

163 g/m

199 g/m

163 g/m

203 g/m

176 g/m

216 g/m

180 g/m

220 g/m

300 g/m

Optional

250‑sheet

drawer

(grain long)

(grain short)

120 g/m

163 g/m

120 g/m

163 g/m

135 g/m

176 g/m

163 g/m

220 g/m

260 g/m

Optional

500‑sheet

drawer

(grain long)

(grain short)

163 g/m

199 g/m

163 g/m

203 g/m

176 g/m

216 g/m

180 g/m

220 g/m

300 g/m

Multipurpose

feeder*

(grain long)

(grain short)

120 g/m

163 g/m

120 g/m

163 g/m

135 g/m

176 g/m

163 g/m

220 g/m

260 g/m

* Due to label design characteristics, unacceptable feeding may be experienced from the multipurpose feeder.

Labels Thickness: 0.102–0.305 mm (0.004–0.012 in.)

Smoothness: 100–400* Sheffield

* 150–250 Sheffield is optimal. Using media higher than 300 Sheffield could result in printing degradation.

Card stock Weight:

Up to 199 g/m

Index Bristol (90 lb)

Up to 203 g/m

Tag (100 lb)

Standard trays and special trays

The Lexmark X642e paper feeding mechanism uses advanced technology that enhances feeding reliability. The standard

Lexmark X642e tray holds 250 or 500 sheets of bond paper and reliably feeds all media tested according to the guidelines

specified under

“Dimensions” on page 9.

For those difficult‑to‑print sizes, such as 3 x 5‑inch index cards, Lexmark offers a variety of special media trays and

drawers.

Note: Optional 250‑sheet Universally Adjustable Trays can be used to print forms with a minimum length of 5 inches

when installed either in the integral tray location or in a 250‑sheet drawer under a 250‑sheet integral tray. Forms

less than 7 inches are not supported from a 400‑sheet universally adjustable tray.

Source Part number

250‑Sheet Mild Special Media Tray 20G1237

250‑Sheet Aggressive Special Media Tray 20G1230

250‑Sheet Mild Special Media Drawer 20G1236

250‑Sheet Aggressive Special Media Drawer 20G1229

250‑Sheet Universally Adjustable Tray 20G1224

250‑Sheet Universally Adjustable Drawer 20G1223

500‑Sheet Mild Special Media Tray 20G1240

500‑Sheet Mild Special Media Tray + Drawer 20G1239

Printer specifications 121

Source Part number

500‑Sheet Aggressive Special Media Tray 20G1227

500‑Sheet Aggressive Special Media Tray + Drawer 20G1226

400‑Sheet Universally Adjustable Tray 20G1217

400‑Sheet Universally Adjustable Tray + Drawer 20G1218

Card stock and label guidelines

Labels are one of the most difficult print materials for laser printers. A special fuser cleaner should be used for label

applications to optimize feed reliability. See your printer documentation for information on ordering additional label

fuser cleaners.

When feeding labels, the number of labels per sheet can affect registration more than basis weight. Typically, the more

labels per sheet, the better the registration.

Printing labels on the X642e, requires a special label fuser cleaner that prevents duplexing.

It is recommended that when you run vinyl labels, you install a special oil fuser cleaner, P/N 40X2665. When you order

a new label cartridge, order the X644H01A high yield return print cartridge or X644X01A extra high yield print cartridge.

It is possible to duplex certain labels that have been specifically designed for this application. To duplex labels, consult

the Lexmark "Converter Lists" to see which converters have successfully developed this type of label, and you must

install a special fuser wiper. The wax wiper that is used with the X642e is P/N 40X2666 (Cartridges designed for duplex

label printing contain two wax wipers. Change the wax wiper at the halfway point of your normal cartridge usage to

provide additional cleaning and optimize performance.)

When printing on labels:

• Set the Paper Type to Labels in the Paper Menu. For vinyl and other heavy labels, set the Paper Type to Vinyl Labels.

Note: When Paper Type is set to Vinyl Labels, the printer reduces the printing speed to ensure acceptable

printing.

• Do not load labels together with paper or transparencies in the same paper tray. Combining print materials can

cause feeding problems.

• Use full label sheets. Partial sheets may cause labels to peel off during printing, resulting in a paper jam. Adhesive

material may contaminate your printer. It could also void your printer and cartridge warranties.

When printing on card stock:

• Set the Paper Type to Card Stock in the Paper Menu.

• Do not use card stock that is creased. It may cause paper jams.

For more information, see the following:

• “Pick roller technology” on page 11

• “Grain orientation” on page 17

• “Maintenance procedures” on page 14

• “Troubleshooting” on page 14

Printer specifications 122

Lexmark X644e, X646e

The Lexmark X644e and X646e print on many labels designed for use with laser printers.

The following table lists the maximum weights supported by the trays and the multipurpose feeder.

Note: Scanning large quantities of labels is not recommended.

Paper source

Grain

direction

Card stock Labels

Index

Bristol

Tag Cover Paper

Dual‑web

paper

Polyester Vinyl

Integrated

tray

grain long

grain short

163 g/m

199 g/m

163 g/m

203 g/m

176 g/m

216 g/m

180 g/m

220 g/m

300 g/m

Optional

250‑sheet

drawer

grain long

grain short

120 g/m

163 g/m

120 g/m

163 g/m

135 g/m

176 g/m

163 g/m

220 g/m

260 g/m

Optional

500‑sheet

drawer

grain long

grain short

163 g/m

199 g/m

163 g/m

203 g/m

176 g/m

216 g/m

180 g/m

220 g/m

300 g/m

Multipurpose

feeder*

grain long

grain short

120 g/m

163 g/m

120 g/m

163 g/m

135 g/m

176 g/m

163 g/m

220 g/m

260 g/m

* Due to label design characteristics, unacceptable feeding may be experienced from the multipurpose feeder.

Labels Thickness: 0.102–0.305 mm (0.004–0.012 in.)

Smoothness: 100–400* Sheffield

* 150–250 Sheffield is optimal. Using media higher than 300 Sheffield could result in printing degradation.

Card stock Weight:

Up to 199 g/m

Index Bristol (90 lb)

Up to 203 g/m

Tag (100 lb)

Printer specifications 123

Standard trays and special trays

The Lexmark X644e and X646e paper feeding mechanism uses advanced technology that enhances feeding reliability.

The standard Lexmark X644e and X646e trays hold 250 or 500 sheets of bond paper and reliably feed all media tested

according to the guidelines specified under

“Dimensions” on page 9.

For those difficult‑to‑print sizes, such as 3 x 5‑inch index cards, Lexmark offers a variety of special media trays and

drawers.

Note: Optional 250‑sheet Universally Adjustable Trays can be used to print forms with a minimum length of 5 inches

when installed either in the integral tray location or in a 250‑sheet drawer under a 250‑sheet integral tray. Forms

less than 7 inches in length are not supported from a 400‑sheet universally adjustable tray.

Source Part number

250‑Sheet Mild Special Media Tray 20G1237

250‑Sheet Aggressive Special Media Tray 20G1230

250‑Sheet Mild Special Media Drawer 20G1236

250‑Sheet Aggressive Special Media Drawer 20G1229

250‑Sheet Universally Adjustable Tray 20G1224

250‑Sheet Universally Adjustable Drawer 20G1223

500‑Sheet Mild Special Media Tray 20G1240

500‑Sheet Mild Special Media Tray + Drawer 20G1239

500‑Sheet Aggressive Special Media Tray 20G1227

500‑Sheet Aggressive Special Media Tray + Drawer 20G1226

400‑Sheet Universally Adjustable Tray 20G1217

400‑Sheet Universally Adjustable Tray + Drawer 20G1218

Card stock and label guidelines

Labels are one of the most difficult print materials for laser printers. A special fuser cleaner should be used for label

applications to optimize feed reliability. See your printer documentation for information on ordering additional label

fuser cleaners.

Printing labels on the X644e and X646e requires a special label fuser cleaner that prevents duplexing.

It is recommended that when you run vinyl labels, you install a special oil fuser cleaner, P/N 40X2665. When you order

a new label cartridge, order the X644H01A high yield return print cartridge or X644X01A extra high yield print cartridge.

It is possible to duplex certain labels that have been specifically designed for this application. To duplex labels, consult

the Lexmark "Converter Lists" to see which converters have successfully developed this type of label, and you must

install a special fuser wiper. The wax wiper that is used with the X644e and X646e is P/N 40X2666 (Cartridges designed

for duplex label printing contain two wax wipers. Change the wax wiper at the halfway point of your normal cartridge

usage to provide additional cleaning and optimize performance.)

Printer specifications 124

When printing on labels:

• Set the Paper Type to Labels in the Paper Menu. For vinyl and other heavy labels, set the Paper Type to Vinyl Labels.

Note: When Paper Type is set to Vinyl Labels, the printer reduces the printing speed to ensure acceptable

printing.

• Do not load labels together with paper or transparencies in the same paper tray. Combining print materials can

cause feeding problems.

• Use full label sheets. Partial sheets may cause labels to peel off during printing, resulting in a paper jam. Adhesive

material may contaminate your printer. It could also void your printer and cartridge warranties.

When feeding labels, the number of labels per sheet can affect registration more than basis weight. Typically, the more

labels per sheet, the better the registration.

When printing on card stock:

• Set the Paper Type to Card Stock in the Paper Menu.

• Do not use card stock that is creased. It may cause paper jams.

For more information, see the following:

• “Pick roller technology” on page 11

• “Grain orientation” on page 17

• “Maintenance procedures” on page 14

• “Troubleshooting” on page 14

Lexmark X651de, X652de, X654de, X656de, and X658de

The Lexmark X651de, X652de, X654de, X656de, and X658de print on many labels designed for use with laser printers.

The following table lists the maximum weights supported by the trays and the multipurpose feeder.

Note: Scanning labels through the ADF is not recommended.

Printer specifications 125

Paper source

Grain

direction

Card stock Labels

Index

Bristol

Tag Cover Paper

Dual‑web

paper

Polyester Vinyl

Integrated

tray

grain long

grain short

163 g/m

199 g/m

163 g/m

203 g/m

176 g/m

216 g/m

180 g/m

220 g/m

300 g/m

Optional

200‑sheet

drawer

grain long

grain short

120 g/m

163 g/m

120 g/m

163 g/m

135 g/m

176 g/m

163 g/m

220 g/m

260 g/m

Optional

550‑sheet

drawer

grain long

grain short

163 g/m

199 g/m

163 g/m

203 g/m

176 g/m

216 g/m

180 g/m

220 g/m

300 g/m

Multipurpose

feeder*

grain long

grain short

120 g/m

163 g/m

120 g/m

163 g/m

135 g/m

176 g/m

163 g/m

220 g/m

260 g/m

* Due to label design characteristics, unacceptable feeding may be experienced from the multipurpose feeder.

Labels Thickness: 0.102–0.305 mm (0.004–0.012 in.)

Smoothness: 100–400* Sheffield

* 150–250 Sheffield is optimal. Using media higher than 300 Sheffield could result in printing degradation.

Card stock Weight:

Up to 199 g/m

Index Bristol (90 lb)

Up to 203 g/m

Tag (100 lb)

Up to 216 g/m

Cover (80 lb)

Standard trays and special trays

The Lexmark X651de, X652de, X654de, X656de, and X658de paper feeding mechanism uses advanced technology that

enhances feeding reliability. The standard Lexmark X651de, X652de, X654de, X656de, and X658de trays hold 250 or

550 sheets of bond paper, and reliably feed all media tested according to the guidelines specified under

“Dimensions”

on page 9.

For difficult‑to‑print sizes, such as 3 x 5‑inch index cards, Lexmark offers a variety of special media trays and drawers.

Notes:

• The X658de does not offer any special media tray or drawer.

• Optional 200‑sheet Universally Adjustable Trays can be used to print forms with a minimum length of five inches

when installed either in the integral tray location or in a 250‑sheet drawer under a 250‑sheet integral tray.

Forms less than seven inches in length are not supported from a 400‑sheet universally adjustable tray.

Source Part number

200‑Sheet Aggressive Special Media Tray 30G0932

200‑Sheet Aggressive Special Media Tray + Drawer 30G0933

200‑Sheet Lockable Universally Adjustable Tray + Drawer 30G0836

200‑Sheet Mild Special Media Tray 30G0890

200‑Sheet Mild Special Media Tray + Drawer 30G0891

Printer specifications 126

Source Part number

200‑Sheet Universally Adjustable Tray + Drawer 30G0871

200‑Sheet Universally Adjustable Tray 30G0872

400‑Sheet Lockable Universally Adjustable Tray + Drawer 30G0859

400‑Sheet Mild Special Media Tray 30G0934

400‑Sheet Mild Special Media Tray + Drawer 30G0935

400‑Sheet Aggressive Special Media Tray 30G0892

400‑Sheet Aggressive Special Media Tray + Drawer 30G0893

400‑Sheet Universally Adjustable Tray + Drawer 30G0860

400‑Sheet Universally Adjustable Tray 30G0861

550‑Sheet Lockable Tray + Drawer 30G0849

Card stock and label guidelines

Labels are one of the most difficult print materials for laser printers. Printing labels on the X651de, X652de, X654de,

X656de, and X658de requires a special fuser cleaner that prevents duplexing. It is recommended that you install a

special oil fuser cleaner, P/N 40X2665, when you run labels. When you order a new cartridge, be sure the cartridge

includes the correct fuser cleaner.

It is possible to duplex certain labels that have been specifically designed for this application. To duplex labels, consult

the Lexmark “Converter Lists” to see which converters have successfully developed this type of label. You must install

a special fuser wiper. The wax wiper that is used with the X651de, X652de, X654de, and X656de printers is P/N 40X2666

(cartridges designed for duplex label printing contain two wax wipers). Change the wax wiper at the halfway point of

your normal cartridge usage to provide additional cleaning and optimize performance. Contact your Supplies and Label

Specialist for information on oil and wax vinyl label cartridges.

Note: We do not recommend using wax wipers with vinyl labels.

When printing on labels:

• Set the Paper Type to Labels in the Paper Menu. For vinyl and other heavy labels, set the Paper Type to Vinyl Labels.

Note: When Paper Type is set to Vinyl Labels, the printer reduces the printing speed to ensure acceptable

printing.

• Do not load labels together with paper or transparencies in the same paper tray. Combining print materials can

cause feeding problems.

• Use full label sheets. Partial sheets may cause labels to peel off during printing, resulting in a paper jam. Adhesive

material may contaminate your printer. It could also void your printer and cartridge warranties.

When feeding labels, the number of labels per sheet can affect registration more than basis weight. Typically, the more

labels per sheet, the better the registration.

When printing on card stock:

• Set the Paper Type to Card Stock in the Paper Menu.

• Do not use card stock that is creased. It may cause paper jams.

For more information, see the following:

• “Pick roller technology” on page 11

• “Grain orientation” on page 17

Printer specifications 127

• “Maintenance procedures” on page 14

• “Troubleshooting” on page 14

Lexmark X734, X736, and X738

Lexmark X734, X736, and X738 printer models support card stock and labels from the standard 550‑sheet tray, an

optional 550‑sheet tray, the multipurpose tray, and the optional 550‑sheet specialty media drawer.

Note: The optional 2,000‑sheet tray does not support card stock or labels.

Tray 1, the optional 550‑sheet tray, and the specialty media tray support approximately 250 sheets of card stock or

labels. The following tables list the maximum weights supported.

Paper source

Card stock

(grain long/grain short)

Index Bristol Tag Cover

Standard 550‑sheet tray (Tray 1)

163–199 g/m

163–203 g/m

163–216 g/m

Optional 550‑sheet tray

Optional 550‑sheet specialty media drawer

163–199 g/m

163–203 g/m

163–216 g/m

Multipurpose tray

163–199 g/m

163–203 g/m

163–216 g/m

Paper source Labels

Dual Web/Paper Polyester Vinyl

Standard 550‑sheet tray (Tray 1)

180 g/m

220 g/m

300 g/m

Optional 550‑sheet tray

Optional 550‑sheet specialty media drawer

180 g/m

220 g/m

300 g/m

Multipurpose tray

180 g/m

220 g/m

300 g/m

Printer specifications 128

Labels Width: 76–216 mm (3–8.5 in.)

Length: 124–356 mm (4.88–14 in.)

Weight:

180–300 g/m

(48–92 lb)

Thickness: 0.13–0.20 mm (0.005–0.008 in.)

Smoothness: 50–300 Sheffield*

* 50–150 Sheffield is optimal. This printer may support labels with smoothness of less than 50 Sheffield

such as coated paper, polyester, vinyl, or other synthetic facestock paper. Using media higher than 200

Sheffield could result in print quality degradation.

Card stock Weight:

Up to 199 g/m

Index Bristol (110 lb)

Up to 203 g/m

Tag (125 lb)

Cover stock Weight:

Up to 216 g/m

(80 lb)

For more information on the supported media sizes, see the printer User's Guide on the publications CD.

Card stock and label guidelines

When printing on labels:

• Print samples on the labels being considered for use before buying large quantities.

• Use only label sheets that have no gaps between the labels.

Acceptable labels

Unacceptable labels

• From the printer control panel or from MarkVision Professional, set Paper Type to Labels.

• Do not print a large number of labels continuously.

• Do not use labels that have coating or sizing applied to make the labels liquid‑resistant.

• Do not use labels that have exposed adhesive on the label sheets.

When printing on card stock:

• Select the appropriate Paper Texture setting.

• For the best print quality, always set Paper Type to Card Stock.

• Use grain short card stock when possible.

• Do not use preprinted card stock manufactured with chemicals that may contaminate the printer.

• Be aware that preprinting, perforation, and creasing may significantly affect the print quality and cause jams or

other paper‑handling problems.

For more information, see

“Pick roller technology” on page 11.

Printer specifications 129

Lexmark X746 and X748

The Lexmark X746 and X748 printer models support card stock and labels from the standard 550‑sheet tray, an optional

550‑sheet tray, the multipurpose feeder, and the optional 550‑sheet specialty media tray.

Note: The optional 2,000‑sheet tray does not support card stock or labels.

Tray 1, the optional 550‑sheet tray, and the specialty media tray support approximately 250 sheets of card stock or

labels. The following table lists the maximum weights supported.

Paper source

Grain

direction

Card stock Labels

Index

Bristol

Tag Cover Paper

Dual‑web

paper

Polyester Vinyl

Standard and

optional

550‑sheet tray

grain long

grain short

199 g/m

163 g/m

203 g/m

176 g/m

216 g/m

180 g/m

220 g/m

300 g/m

Multipurpose

feeder

grain long

grain short

199 g/m

163 g/m

203 g/m

176 g/m

216 g/m

180 g/m

220 g/m

300 g/m

* The multipurpose feeder may not support labels with certain design characteristics.

Labels Width:

76–216 mm (3–8.5 in.)

Length:

124–356 mm (4.88–14 in.)

Weight:

Up to 180 g/m

Paper (48 lb)

Up to 180 g/m

Dual Web Paper (48 lb)

Up to 220 g/m

Polyester (59 lb)

Up to 300 g/m

Vinyl (92 lb)

Thickness: 0.13–0.20 mm (0.005–0.008 in.)

Smoothness:

50–300 Sheffield

Printer specifications 130

The minimum size for labels supported in the multipurpose feeder is 76 x 124 mm (3 x 4.88 in.). The

minimum size for labels supported in the standard and optional trays is 148 x 210 mm (5.82 x 8.26 in.)

50–150 Sheffield is optimal. This printer may support labels with smoothness of less than 50 Sheffield

such as coated paper, polyester, vinyl, or other synthetic facestock paper. Using media higher than

200 Sheffield could result in print quality degradation.

Card stock Weight:

Up to 199 g/m

Index Bristol (110 lb)

Up to 203 g/m

Tag (125 lb)

Up to 216 g/m

Cover (80 lb)

For more information on the supported media sizes, see the printer User's Guide on the Software and

Documentation CD.

Card stock and label guidelines

When printing on labels:

• Print samples on the labels being considered for use before buying large quantities.

• Use only label sheets that have no gaps between the labels.

Acceptable labels

Unacceptable labels

• From the printer control panel or from MarkVision Professional, set Paper Type to Labels.

• Do not print a large number of labels continuously.

• Do not use labels that have coating or sizing applied to make the labels liquid‑resistant.

• Do not use labels that have exposed adhesive on the label sheets.

• Run the labels only once through the printer as this may contaminate the printer.

When printing on card stock:

• Select the appropriate Paper Texture setting.

• For the best print quality, always set Paper Type to Card Stock.

• Use grain short card stock when possible.

• Do not use preprinted card stock manufactured with chemicals that may contaminate the printer.

• Be aware that preprinting, perforation, and creasing may significantly affect the print quality and cause jams or

other paper‑handling problems.

For more information, see

“Pick roller technology” on page 11.

Printer specifications 131

Lexmark X782

The Lexmark X782 can print on many labels designed for use with laser printers.

The following tables list the maximum weights supported by the trays and the multipurpose feeder.

Note: The optional 2000‑sheet drawer supports plain and glossy paper.

Paper source

Card stock

(grain long/grain short)

Index Bristol Tag Cover

grain long grain short grain long grain short grain long grain short

500‑sheet drawers

163 g/m

199 g/m

163 g/m

203 g/m

176 g/m

216 g/m

Multipurpose feeder

163 g/m

199 g/m

163 g/m

203 g/m

176 g/m

216 g/m

Paper source

Labels

Paper Dual‑web paper Polyester Vinyl

1, 2

500‑sheet drawers

180 g/m

220 g/m

300 g/m

Multipurpose feeder

199 g/m

220 g/m

260 g/m

Vinyl labels are supported only when the printing environment and media are 20–32.2°C (68–90°F).

The skew performance of heavy vinyl labels may be enhanced by feeding from an optional 500‑sheet drawer if placement

of the image is critical.

For paper and transparency specifications, see the printer User's Guide on the publications CD.

Labels Thickness: 0.102–0.305 mm (0.004–0.012 in.)

Smoothness: 50–300* Sheffield

* 50–150 Sheffield is optimal. This printer may support labels with smoothness of less than 50 Sheffield such as coated paper,

polyester, vinyl, or other synthetic facestock papers. Using media higher than 200 Sheffield could result in print quality

degradation.

Printer specifications 132

Card stock and label guidelines

Labels are one of the most difficult print materials for laser printers. A fuser equipped with a dry web cleaner may be

required for label applications to optimize feed reliability. If you print large quantities of labels or other glossy print

media, then install a dry web cleaner upgrade kit (P/N 40X1856). Contact your local service representative for ordering

information.

When printing on labels:

• From the printer control panel, set Paper Type to Labels in the Paper Menu. For vinyl and other heavy labels, set

Labels Weight (under the Paper Weight menu) to Heavy, and set Labels Texture (under the Paper Texture menu)

to Smooth.

• Do not load labels together with paper or transparencies in the same paper tray. Combining print materials can

cause feeding problems.

• Use full label sheets. Partial sheets may cause labels to peel off during printing, resulting in a paper jam. Adhesive

material may contaminate your printer. It could also void your printer and cartridge warranties.

Print on sheets with more number of labels to improve registration.

When printing on card stock:

• From the printer control panel, set Paper Type to Card Stock in the Paper Menu.

• Do not use creased card stock. It may cause paper jams.

For more information, see the following:

• “Pick roller technology” on page 11

• “Maintenance procedures” on page 14

• “Troubleshooting” on page 14

Printer specifications 133

Lexmark X792de, X792dte, X792dtfe, X792dtpe, X792dtme, and

X792dtse

The Lexmark X792de, X792dte, X792dtfe, X792dtpe, X792dtme, and X792dtse printer models support card stock and

labels from the standard 550‑sheet tray, an optional 550‑sheet tray, and the multipurpose feeder.

Note: The optional 2000‑sheet drawer does not support card stock or labels.

Overview of card stock support

Paper source

Card stock

(grain long/grain short)

Index Bristol Tag Cover

grain long grain short grain long grain short grain long grain short

Standard and optional

550‑sheet trays

163 g/m

199 g/m

163 g/m

203 g/m

176 g/m

216 g/m

Multipurpose feeder

163 g/m

199 g/m

163 g/m

203 g/m

176 g/m

216 g/m

Printer specifications 134

Overview of label support

Paper source

Labels

Paper Dual‑web paper Polyester Vinyl

1, 2

Standard and optional 550‑sheet trays

180 g/m

220 g/m

300 g/m

Multipurpose feeder

199 g/m

220 g/m

260 g/m

Vinyl labels are supported only when the printing environment and media are 20–32.2°C (68–90°F).

The skew performance of heavy vinyl labels may be enhanced by feeding from an optional 500‑sheet drawer if placement

of the image is critical.

Media specifications

Labels Width: 76.2–139.7 mm (3–8.5 in.)

Length: 127–355.6 mm (5–14 in.)

Weight:

160–220 g/m

160–300 g/m

(Vinyl)

Thickness: Up to 0.25 mm

Smoothness: 50–300 Sheffield*

* 50–150 Sheffield is optimal. This printer may support labels with smoothness of less than 50 Sheffield

such as coated paper, polyester, vinyl, or other synthetic facestock paper. Using media higher than 200

Sheffield could result in print quality degradation.

Card stock Width: 76.2–139.7 mm (3–8.5 in.)

Length: 127–355.6 mm (5–14 in.)

Weight:

Up to 216 g/m

Use only materials recommended for use with laser printers.

To prevent specialty media sheets from sticking together, remove each sheet from the bin as it is printed.

Card stock and label guidelines

When printing on labels:

• Set Paper Type to Labels from the printer driver.

• Use A4- or letter-size paper.

• Do not use label sheets with a slick backing material.

• Do not print within 1 mm (0.040 inch) of the die-cut.

• Use full label sheets. Partial sheets may cause labels to peel off during printing, resulting in a paper jam. Partial

sheets will also contaminate your printer and your cartridge with adhesive, and could void your printer and cartridge

warranties.

• Use labels that can withstand temperatures of 180°C (356°F) without sealing, excessive curling, wrinkling, or

releasing hazardous emissions.

• Verify that the adhesive material of the label can tolerate a fusing temperature of 180°C (356°F) for 0.1 second.

• Use labels that can withstand pressure of 25 pounds per square inch (psi).

• Do not print within 1 mm (0.040 inch) of the edge of the label, of the perforations, or between die-cuts of the label.

Printer specifications 135

• Do not use label sheets that have adhesive to the edge of the sheet. We recommend zone coating of the adhesive

at least 1 mm (0.040 inch) away from edges. Adhesive material will contaminate your printer and could void your

warranty.

• If zone coating of the adhesive is not possible, a 3‑mm (0.125‑inch) strip should be removed on the leading and

driver edge, and a non‑oozing adhesive should be used.

• Remove a 3‑mm (0.125‑inch) strip from the leading edge to prevent labels from peeling inside the printer.

• Portrait orientation is preferred, especially when printing bar codes.

• Do not use labels that have exposed adhesive.

• Do not use labels that are separating from the backing sheet or are wrinkled, bubbled, or otherwise damaged.

• Do not load a sheet of labels through the machine more than once.

• Load labels into the multipurpose feeder with the recommended print side faceup and the top edge entering the

printer first.

When printing on card stock:

• Set Paper Type to Card Stock from the printer driver.

• Do not use preprinted card stock manufactured with chemicals that may contaminate the printer. Preprinting

introduces semi‑liquid and volatile components into the printer.

• Do not use creased card stock. It may cause paper jams.

• We recommend the use of grain short card stock.

• Load card stock into the multipurpose feeder with the recommended print side faceup and the top edge entering

the printer first.

Lexmark X850, X852e, and X854e

Limit label printing to occasional use of paper office labels designed for laser printers. Paper labels are supported in

Tray 1, Tray 2, and the manual bypass feeder.

The following table lists the maximum weights supported.

Note: Scanning large quantities of labels is not recommended.

Printer specifications 136

Tray 1 Tray 2 Multipurpose feeder

Labels

64–105 g/m

64–216 g/m

Card stock

64–105 g/m

64–216 g/m

Labels Width: 89–297 mm (3.5–11.7 in.)

Length: 99–432 mm (3.9–17 in.)

Weight:

64–216 g/m

Thickness: Up to 0.25 mm

Smoothness: 100–400 Sheffield*

* 150–250 Sheffield is optimal. Using media higher than 300 Sheffield could result in printing degradation.

Card stock Width: 89–297 mm (3.5–11.7 in.)

Length: 99–432 mm (3.9–17 in.)

Weight:

Up to 216 g/m

Use only materials recommended for use with laser printers.

To prevent specialty media sheets from sticking together, remove each sheet from the output bin as it is printed.

Card stock and label guidelines

When printing on labels:

• Set the Paper Type to Labels from the printer driver.

• Use standard‑size products (either A4 or Letter).

• Do not use label sheets with a slick backing material.

• Do not print within 1 mm (0.040 in.) of the die-cut.

• Use full label sheets. Partial sheets may cause labels to peel off during printing, resulting in a paper jam. Partial

sheets will also contaminate your printer and your cartridge with adhesive, and could void your printer and cartridge

warranties.

• Use labels that can withstand temperatures of 180°C (356°F) without sealing, excessive curling, wrinkling, or

releasing hazardous emissions.

• Verify that your label adhesive material can tolerate a fusing temperature of 180°C (356°F) for 0.1 second.

• Use labels that can withstand pressure of 25 pounds per square inch (psi).

• Do not print within 1 mm (0.040 in.) of the edge of the label, of the perforations, or between die-cuts of the label.

• Do not use label sheets that have adhesive to the edge of the sheet. We recommend zone coating of the adhesive

at least 1 mm (0.040 in.) away from edges. Adhesive material will contaminate your printer and could void your

warranty.

• If zone coating of the adhesive is not possible, a 3‑mm (0.125‑in.) strip should be removed on the leading and driver

edge, and a non‑oozing adhesive should be used.

• Remove a 3‑mm (0.125‑in.) strip from the leading edge to prevent labels from peeling inside the printer.

• Portrait orientation is preferred, especially when printing bar codes.

• Do not use labels that have exposed adhesive.

• Do not use labels that are separating from the backing sheet or are wrinkled, bubbled, or otherwise damaged.

Printer specifications 137

• Do not load a sheet of labels through the machine more than once.

• Load labels into the manual bypass feeder with the recommended print side faceup and the top edge going in first.

When printing on card stock:

• Set the Paper Type to Card Stock from the printer driver.

• Do not use preprinted card stock manufactured with chemicals that may contaminate the printer. Preprinting

introduces semi‑liquid and volatile components into the printer.

• Do not use card stock that is creased. It may cause paper jams.

• We recommend the use of grain short card stock.

• Load card stock into the manual bypass feeder with the recommended print side faceup and the top edge going in

first.

Lexmark X860e, X862e, and X864e

Limit label printing to occasional use of A4‑ or letter‑size paper office labels designed for laser printers. We do not

recommend using vinyl or polyester labels.

The Lexmark X860e, X862e, and X864e support stocks up to 216 g/m

. Always feed labels and card stock from Tray 1,

2 or the multipurpose feeder.

The following table lists the maximum weights supported by the trays and the multipurpose feeder.

Paper source Media types Weight

Tray 1 Paper, Labels, Transparencies

64‑105 g/m

Tray 2 Paper, Card stock, Labels, Transparencies

64‑216 g/m

Multipurpose feeder Paper, Card stock, Envelopes, Labels, Transparencies

64‑216 g/m

Printer specifications 138

Labels Width: 89–297 mm (3.5–11.7 in.)

Length: 99–432 mm (3.9–17 in.)

Weight:

64‑216 g/m

Thickness: Up to 0.25 mm

Smoothness: 100–400 Sheffield*

* 150–250 Sheffield is optimal. Using media higher than 300 Sheffield could result in printing degradation.

Card stock Width: 89–297 mm (3.5–11.7 in.)

Length: 99–432 mm (3.9–17 in.)

Weight:

Up to 216 g/m

Card stock and label guidelines

When printing on labels:

• Set the Paper Type to Labels from the printer driver.

• Use standard‑size products (either A4 or Letter).

• Do not use label sheets with a slick backing material.

• Do not print within 1 mm (0.040 in.) of the die-cut.

• Use full label sheets. Partial sheets may cause labels to peel off during printing, resulting in a paper jam. Partial

sheets will also contaminate your printer and your cartridge with adhesive, and could void your printer and cartridge

warranties.

• Use labels that can withstand temperatures of 180°C (356°F) without sealing, excessive curling, wrinkling, or

releasing hazardous emissions.

• Verify that your label adhesive material can tolerate a fusing temperature of 180°C (356°F) for 0.1 second.

• Use labels that can withstand pressure of 25 pounds per square inch (psi).

• Do not print within 1 mm (0.040 in.) of the edge of the label, of the perforations, or between die-cuts of the label.

• Do not use label sheets that have adhesive to the edge of the sheet. We recommend zone coating of the adhesive

at least 1 mm (0.040 in.) away from edges. Adhesive material will contaminate your printer and could void your

warranty.

• If zone coating of the adhesive is not possible, a 3‑mm (0.125‑in.) strip should be removed on the leading and driver

edge, and a non‑oozing adhesive should be used.

• Remove a 3‑mm (0.125‑in.) strip from the leading edge to prevent labels from peeling inside the printer.

• Portrait orientation is preferred, especially when printing bar codes.

• Do not use labels that have exposed adhesive.

• Do not use labels that are separating from the backing sheet or are wrinkled, bubbled, or otherwise damaged.

• Do not load a sheet of labels through the machine more than once.

• Load labels into the manual bypass feeder with the recommended print side faceup and the top edge going in first.

When printing on card stock:

• Set the Paper Type to Card Stock from the printer driver.

• Do not use preprinted card stock manufactured with chemicals that may contaminate the printer. Preprinting

introduces semi‑liquid and volatile components into the printer.

• Do not use card stock that is creased. It may cause paper jams.

Printer specifications 139

• We recommend the use of grain short card stock.

• Load card stock into the manual bypass feeder with the recommended print side faceup and the top edge going in

first.

Lexmark X925

Limit label printing to occasional use of A4‑ or letter‑size paper office labels designed for laser printers. We do not

recommend using vinyl or polyester labels.

Trays and the multipurpose feeder support card stock. The multipurpose feeder supports card stocks up to 256 g/m

Always feed labels from the standard 150‑sheet tray or the multipurpose feeder.

The standard 250‑ and optional 550‑sheet trays do not support labels.

The following table lists the maximum weights supported by the trays and the multipurpose feeder.

Paper source

Card stock

(grain long/grain short)

Index Bristol Tag Cover

grain long grain short grain long grain short grain long grain short

Standard 150‑sheet

tray

120 g/m

163 g/m

120 g/m

163 g/m

135 g/m

176 g/m

Standard 250‑ and

optional 550‑sheet

trays

120 g/m

157 g/m

120 g/m

157 g/m

135 g/m

157 g/m

Multipurpose feeder

120 g/m

256 g/m

120 g/m

256 g/m

135 g/m

256 g/m

Printer specifications 140

Paper source

Labels

Paper Vinyl

Standard 150‑sheet tray

131 g/m

Not applicable

Multipurpose feeder

131 g/m

Occasional use up to

256 g/m

Labels Width: 210–216 mm (8.3–8.5 in.)

Length: 279–356 mm (11–11.7 in.)

Weight:

120–128 g/m

Thickness: 0.13–0.20 mm (0.005–0.008 in.)

Smoothness: 100–400 Sheffield*

* 150–250 Sheffield is optimal. Using media higher than 300 Sheffield could result in print quality

degradation.

Card stock Width: 210–216 mm (8.3–8.5 in.)

Length: 279–356 mm (11–11.7 in.)

Weight:

Up to 216 g/m

Card stock and label guidelines

When printing on labels:

• From the printer control panel, set Paper Type to Labels in the Paper Menu.

• Do not use label sheets with a slick backing material.

• Do not print within 1 mm (0.04 in.) of the die-cut, the edge of the label or the perforations, or between the die-

cuts.

• Use full label sheets. Partial sheets may cause labels to peel off during printing, resulting in a paper jam.

• Do not use label sheets that have adhesive to the edge of the sheet. We recommend zone coating of the adhesive

at least 1 mm (0.04 in.) away from the edges. Adhesive material may contaminate your printer and could void your

warranty.

When printing on card stock:

• Use grain long card stock, and set Paper Type to Card Stock.

• Do not use creased card stock. It may cause paper jams.

Printer specifications 141

Lexmark X940 and X945

Limit label printing to occasional use of A4‑ or letter‑size paper office labels designed for laser printers. We do not

recommend using vinyl or polyester labels.

Lexmark X940 and X945 support stocks up to 220 g/m

. Always feed labels and card stock from Tray 1, 2, or 3. We

recommend printing on grain long card stock.

The following table lists the maximum weights supported by the trays and the multipurpose feeder.

Note: Scanning large quantities of labels is not recommended.

Tray 1 Tray 2 and 3 Multipurpose feeder

Labels

105 g/m

220 g/m

Card stock

105 g/m

220 g/m

Labels Width: 210–216 mm (8.3–8.5 in.)

Length: 279–356 mm (11–11.7 in.)

Weight:

120–128 g/m

Thickness: 0.13–0.20 mm (0.005–0.008 in.)

Smoothness: 100–400 Sheffield*

* 150–250 Sheffield is optimal. Using media higher than 300 Sheffield could result in print quality

degradation.

Card stock Width: 210–216 mm (8.3–8.5 in.)

Length: 279–356 mm (11–11.7 in.)

Weight:

Up to 220 g/m

Card stock and label guidelines

When printing on labels:

• Set the paper type to Labels in the Paper Menu.

• Do not use label sheets with a slick backing material.

Printer specifications 142

• Do not print within 1 mm (0.04 in.) of the die-cut, the edge of the label or the perforations, or between the die-

cuts.

• Use full label sheets. Partial sheets may cause labels to peel off during printing and result in a paper jam.

• Do not use label sheets that have adhesive to the edge of the sheet. We recommend zone coating of the adhesive

at least 1 mm (0.04 in.) away from the edges. Adhesive material may contaminate your printer and could void your

warranty.

When printing on card stock:

• Use grain long card stock, and set the paper type to Card Stock.

• Do not use creased card stock. It may cause paper jams.

Lexmark X950

Limit label printing to occasional use of A4‑ or letter‑size paper office labels designed for laser printers. We do not

recommend using vinyl or polyester labels.

Lexmark X950 supports card stock up to 300 g/m

The following table lists the maximum weights supported by the trays and the multipurpose feeder.

Trays 1–4 Multipurpose feeder High‑capacity feeder

Labels

60–256 g/m

60–300 g/m

60–216 g/m

Card stock

60–256 g/m

60–300 g/m

60–216 g/m

Labels Width: 140–320 mm (5.5–12.6 in.)

Length: 182–457 mm (7.2–18 in.)

Weight:

60–256 g/m

Smoothness: 100–200 Sheffield

Card stock Width: 140–320 mm (5.5–12.6 in.)

Length: 182–457 mm (7.2–18 in.)

Weight:

60–256 g/m

Printer specifications 143

Card stock and label guidelines

When printing on labels:

• From the printer control panel, set the paper size, type, texture, and weight in the Paper menu to match the labels

loaded in the tray.

• Do not use label sheets with a slick backing material.

• Do not print within 1 mm (0.04 in.) of the die‑cut, the edge of the label or the perforations, or between the die‑cuts.

• Use full label sheets. Partial sheets may cause labels to peel off during printing, resulting in a jam. Partial sheets

also contaminate the printer and the cartridge with adhesive, and could void the printer and toner cartridge

warranties.

When printing on card stock:

• From the printer control panel, set the paper size, type, texture, and weight in the Paper menu to match the card

stock loaded in the tray.

• Do not use creased card stock. It may cause paper jams.

• We recommend the use of grain long card stock.

Optra plus, 4039, 4029, 4019, WinWriter 600 printers

The following table lists the maximum weights supported by each of the special card stock and label trays, as well as

the manual feed tray.

Paper source

Card stock Labels

Index Bristol Tag Cover Paper Vinyl

200‑sheet heavy duty tray

163 g/m

176 g/m

150 g/m

265 g/m

500‑sheet tray (450 grams)

90 g/m

————

500‑sheet tray (550 grams)

135 g/m

165 g/m

—

500‑sheet tray (650 grams)

163 g/m

176 g/m

175 g/m

300 g/m

500‑sheet tray (750 grams)

199 g/m

203 g/m

216 g/m

180 g/m

300 g/m

Manual feed tray

253 g/m

241 g/m

285 g/m

263 g/m

300 g/m

For paper and transparency specifications, see your printer User's Guide.

As the following table indicates, the paper tray capacities vary depending on the print material construction. See your

printer documentation for additional specifications.

Printer specifications 144

Label material 200‑sheet heavy duty tray 500‑sheet card stock & label tray

Paper, dual web 125 sheets 250 sheets

Vinyl, polyester 70 sheets 200 sheets

The following table lists the print material specifications for the special card stock and label trays, as well as guidelines

for the tray position (upper or lower drawer). This information is intended to convey general guidelines for tray and

drawer selection. We recommend that you test your selected print material to determine the best tray and drawer

selection for your application. The material type, rigidity, sizing, perforations, die-cuts, and surface influence printing

reliability. Contact your point of purchase for more information on the optional trays available for your printer.

Note: If you use materials with a weight over 135 g/m

(36 lb bond), print registration and skew may be

unpredictable.

Media Paper/card stock

Pressure‑sensitive paper

labels

Pressure‑sensitive vinyl

labels

200‑sheet heavy duty tray

75–163 g/m

(20–43 lb bond)

120–150 g/m

(32–40 lb bond)

260–265 g/m

82 lb Liner

500‑sheet tray (450 grams)

60–90 g/m

(16–24 lb bond)

NA NA

500‑sheet tray (550 grams)

75–135 g/m

(20–36 lb bond)

140–165 g/m

(37–44 lb bond)

500‑sheet tray (650 grams)

120–163 g/m

(32–43 lb bond)

150–175 g/m

(40–47 lb bond)

260–300 g/m

82–92 lb Liner

500‑sheet tray (750 grams)

163–203 g/m

(43–54 lb bond)

165–180 g/m

(44–48 lb bond)

265–300 g/m

92 lb Liner

Valid tray positions (upper

and lower)

Upper: 60–163 g/m

Lower: All supported media

Upper: 120–150 g/m

Lower: 140–180 g/m

Upper: 260–265 g/m

Lower: 260–300 g/m

You can manually feed card stock with a weight up to 285 g/m

For pressure‑sensitive materials under 131 g/m

, grain long is recommended. For pressure‑sensitive materials over

131 g/m

, grain short is recommended.

Media

Dual web forms

Pressure‑sensitive area

Paper base

Integrated forms

Pressure‑sensitive area

Paper base

200‑sheet heavy duty tray

140–175 g/m

75–135 g/m

(20–36 lb bond)

140–175 g/m

75–135 g/m

(20–36 lb bond)

500‑sheet tray (450 grams) —

—

75–90 g/m

(20–24 lb bond)

Select the appropriate tray according to the part of the form (pressure‑sensitive area or paper base) that enters the printer

first when feeding from the tray.

Grain long is recommended.

Printer specifications 145

Media

Dual web forms

Pressure‑sensitive area

Paper base

Integrated forms

Pressure‑sensitive area

Paper base

500‑sheet tray (550 grams)

140–175 g/m

75–131 g/m

(20–35 lb bond)

140–170 g/m

75–135 g/m

(20–36 lb bond)

500‑sheet tray (650 grams) —

—

170–175 g/m

500‑sheet tray (750 grams) —

—

Valid tray positions (upper and

lower)

Upper and Lower: All supported media Upper and Lower: All supported media

Select the appropriate tray according to the part of the form (pressure‑sensitive area or paper base) that enters the printer

first when feeding from the tray.

Grain long is recommended.

Labels Thickness: 0.102–0.254 mm (0.004–0.01 in.)

Smoothness: 100–400* Sheffield

* 150–250 Sheffield is optimal. Using media higher than 300 Sheffield could result in printing degradation.

Card stock Weight:

Up to 163 g/m

Index Bristol (90 lb)

Up to 163 g/m

Tag (100 lb)

Maintenance procedures

For reliable printer performance when feeding card stock and labels, follow the appropriate maintenance procedures

outlined in the following sections.

General maintenance

If the print quality begins to degrade when printing sheets of vinyl labels, we suggest you follow the three cleaning

steps below:

1 Print 5 sheets of paper.

2 Wait approximately 5 seconds.

3 Print 5 more sheets of paper.

To maintain printer feeding reliability, repeat this cleaning process every time you replace the print cartridge, more

often with some media. Failure to follow maintenance procedures could cause jamming, poor print quality, feeding

problems, and fuser problems.

Printer specifications 146

Additional maintenance for Optra plus, Optra, 4039 12C (with serial numbers after BC143), and

4039 10 plus printers

• If your laser printer has a fuser cleaner, we recommend that you change it when you replace the print cartridge. If

you are printing on labels or card stock, you may need to change the fuser cleaner more frequently. Check the fuser

cleaner every 2,000 pages, and replace it if it is crusty or stiff. See your printer documentation for information about

ordering additional fuser cleaners. Using a substitute cleaner may result in degraded print quality and may void

your printer warranty.

• Use a 4039 print cartridge (P/N 1380850 or 1380950) in Optra and Optra plus laser printers that are dedicated to

printing labels. Machine engine code level 43.74 or later is required to use the 4039 cartridges in your Optra and

Optra plus printer. Print the menus page from the Tests Menu to determine the level of engine code installed in

your printer. Contact Lexmark customer support if you need assistance upgrading to a higher level.

• Always use the fuser cleaners that come with the 4039 print cartridges. If you need additional fuser cleaners, order

P/N 1380785. This particular fuser cleaner has oil in the pad to lubricate the fuser and prolong fuser life. It also

lessens toner buildup on some labels, ensuring good print quality.

• We recommend using the fuser cleaner shipped with Diamond Fine

toner cartridges (P/N 1382100 or 1382150)

when duplexing.

• Note that 4039 print cartridges are not recommended for general use in Optra printers, since they cannot provide

the 1200 dpi quality desirable for graphics and gray scaling. Using third party, non

‑

Lexmark cartridges and fuser

cleaners can void the printer warranty. Using refilled non‑Lexmark cartridges can result in toner build‑up in the

printer, which increases the potential of toner contamination.

• Some card stock and labels generate a large amount of paper dust, debris, and chaff. To remove excess dust and

debris, you may need to clean the inside of the printer frequently, possibly daily. Consult your printer documentation

for specific instructions on how to properly clean your printer. Removing debris helps improve paper feeding and

fuse grade.

• See your printer documentation for other maintenance procedures to maintain the print quality and reliability of

your printer.

For more information, see

“Troubleshooting” on page 14.

Optra C

We do not recommend using card stock or labels with this printer.

Card stock and labels are not supported from any of the paper trays.

For paper and transparency specifications, see the printer User's Guide.

Printer specifications 147

Optra C710

Limit label printing to occasional use of paper office labels designed for laser printers. We do not recommend using

vinyl or polyester labels.

The Optra C710 supports stocks up to 163 g/m

(90 lb). Feed labels from the multipurpose feeder only, which holds up

to 30 sheets of card stock or labels.

The following table lists the maximum weights supported by the multipurpose feeder.

Paper source

Card stock Labels

Index Bristol Tag Cover Paper Vinyl

Multipurpose

feeder

163 g/m

—

163 g/m

—

For paper and transparency specifications, see the printer User's Guide.

Labels Width: 210–216 mm (8.3–8.5 in.)

Length: 279–297 mm (11–11.7 in.)

Weight:

120–163 g/m

(32–43 lb)

Thickness: 0.13–0.20 mm (0.005–0.008 in.)

Smoothness: 100–400 Sheffield*

* 150–250 Sheffield is optimal. Using media higher than 300 Sheffield could result in printing degradation.

Card stock Weight:

Up to 163 g/m

Index Bristol (90 lb)

Up to 163 g/m

Tag (100 lb)

Printer specifications 148

Card stock and label guidelines

When printing on labels:

• Use only label sheets that have no gaps between the labels.

Acceptable labels

Unacceptable labels

• From the operator panel or from MarkVision Professional, set the Paper Type to Labels.

• Do not print a large number of labels continuously.

• Do not use labels that have coating or sizing applied to make the labels liquid‑resistant.

• Do not use labels that have exposed adhesive on the label sheets.

When printing on card stock:

• We recommend using Springhill Index Plus 90 lb card stock.

• For the best print quality, always set the Paper Type to Card Stock.

Optra Color 1200

Limit label printing to occasional use of paper office labels designed for laser printers. We do not recommend using

vinyl or polyester labels.

The Optra Color 1200 supports stock up to 163 g/m

(43 lb).

Always feed labels and card stock from the multipurpose feeder. The multipurpose feeder holds up to 50 sheets of

labels or card stock.

The following table lists the maximum weights supported by the multipurpose feeder.

Printer specifications 149

Paper source

Card stock Labels

Index Bristol Tag Cover Paper Vinyl

Multipurpose feeder

163 g/m

—

135 g/m

—

For paper and transparency specifications, see the printer User's Guide.

Labels Width: 210–216 mm (8.3–8.5 in.)

Length: 279–356 mm (11–14 in.)

Weight:

60–135 g/m

Card stock Weight

Up to 163 g/m

Index Bristol (90 lb)

Up to 163 g/m

Tag (100 lb)

Optra E, Ep

Limit label printing to occasional use of paper office labels designed for laser printers. We do not recommend using

vinyl or polyester labels.

The Optra E and Optra Ep support stocks up to 163 g/m

(43 lb). Tray 1 can hold up to 10 sheets of card stock or labels.

The following table lists the maximum weights supported by Tray 1 and the manual feed slot.

Paper source

Card stock Labels

Index Bristol Tag Cover Paper Vinyl

Tray 1

163 g/m

—

150 g/m

—

Manual feed slot

163 g/m

—

150 g/m

—

For paper and transparency specifications, see the printer User's Guide.

Labels Width: 210–216 mm (8.3–8.5 in.)

Length: 279–297 mm (11–11.7 in.)

Weight:

120–150 g/m

(32–39 lb)

Thickness: 0.13–0.25 mm (0.005–0.01 in.)

Smoothness: 100–400 Sheffield*

* 150–250 Sheffield is optimal. Using media higher than 300 Sheffield could result in printing degradation.

Printer specifications 150

Card stock Weight:

Up to 163 g/m

Index Bristol (90 lb)

Up to 163 g/m

Tag (100 lb)

For more information, see “Maintenance procedures” on page 14.

Optra E310, E312

Limit label printing to occasional use of paper office labels designed for laser printers. We do not recommend using

vinyl or polyester labels.

The Optra E310 and Optra E312 support stocks up to 163 g/m

(43 lb). The automatic paper feeder can hold up to

10 sheets of card stock or labels.

The following table lists the maximum weights supported by the automatic paper feeder and the multipurpose feeder.

Paper Source

Card Stock Labels

Index Bristol Tag Cover Paper Vinyl

Automatic Paper Feeder

163 g/m

—

163 g/m

—

Manual Sheet Feeder

163 g/m

—

163 g/m

—

For paper and transparency specifications, see the printer User's Guide.

Labels Width: 210–216 mm (8.3–8.5 in.)

Length: 279–297 mm (11–11.7 in.)

Weight:

Up to 163 g/m

(43 lb)

Thickness: Up to 0.25 mm (0.01 in.)

Smoothness: 100–400* Sheffield

* 150–250 Sheffield is optimal. Using media higher than 300 Sheffield could result in printing degradation.

Card stock Weight:

Up to 163 g/m

Index Bristol (90 lb)

Up to 163 g/m

Tag (100 lb)

Note: Always use the front exit when printing on card stock. To minimize curl, use the front exit when printing on labels.

For more information, see “Maintenance procedures” on page 14.

Printer specifications 151

Optra Es special media printer

The Optra Es printer has highly precise print registration and excellent feeding reliability. It was designed to handle a

wide range of paper and card stock weights, as well as continuous printing of labels.

The following table lists the maximum weights supported by Tray 1 and the manual feed slot.

Paper source

Card stock Labels

Index Bristol Tag Cover Paper Vinyl

Tray 1

199 g/m

163 g/m

176 g/m

180 g/m

300 g/m

Manual feed slot

199 g/m

163 g/m

176 g/m

180 g/m

300 g/m

For paper and transparency specifications, see the printer User's Guide.

Selecting and loading media

Your printer can accept a wide range of paper or card stock weights, but materials either too light or too heavy can

cause paper handling and print quality problems. Heavier weight materials can cause fusing problems because of the

mass of material the fuser must heat quickly. Heavy materials may also feed less reliably or skew because of their weight

or stiffness. Lighter materials can wrinkle or jam.

When you use preprinted forms, make sure the ink on the forms can withstand the printer fuser temperature of 200°C

(392°F); otherwise, you risk contaminating the printer or creating hazardous fumes.

When you select the correct Paper Type (Normal, Rough Paper, Card Stock, Transparency, Labels) from MarkVision

Professional, your printer automatically optimizes print quality and toner adhesion.

Feed labels, card stock, transparencies, and envelopes from Tray 1 or the manual feed slot. Reserve Tray 2 for 20–24 lb

bond paper. Do not load labels together with other media in the same paper tray; combining different print media can

cause feeding problems. To avoid curl, do not leave labels in the tray overnight.

When feeding labels from Tray 1, push the label lever to the left. When printing on other media, push the lever to the

right.

To improve feed reliability, flex the print media before placing it in the paper tray.

Printer specifications 152

Source Print media

Maximum stack

height

Input capacity Output capacity

Tray 1 Paper 20 lb bond 15 mm (0.6 in.) 150 sheets 100 sheets

24 lb bond 15 mm (0.6 in.) 100 sheets 100 sheets

Labels Paper 13 mm (0.5 in.) 70 sheets 70 sheets

Vinyl 13 mm (0.5 in.) 35–50 sheets 35–50 sheets

Dual Web Forms

Integrated Forms

13 mm (0.5 in.) 50–60 sheets 50–60 sheets

Card stock

1,2

Index 163 g/m

(90 lb)

7 mm (0.3 in.) 35 sheets 35 sheets

Index 199 g/m

(110 lb)

7 mm (0.3 in.) 30 sheets 1 sheet

Tag 163 g/m

(100 lb)

7 mm (0.3 in.) 30 sheets 30 sheets

Envelopes (20 lb) 13 mm (0.5 in.) 10 envelopes 10 envelopes

Transparencies 2.5 mm (0.1 in.) 10 sheets 10 sheets

Tray 2 Paper 20 lb bond 25 mm (1 in.) 250 sheets 250 sheets

24 lb bond 25 mm (1 in.) 150 sheets 150 sheets

Manual All supported media — 1 sheet 1 sheet

Card stock weights may vary ± 5%.

110 lb Index recommended for applications using only solid black lines, text, or area fills. Applications using gray scales

may have unpredictable results.

For more information, see “Maintenance procedures” on page 14.

Optra K 1220

Limit label printing to occasional use of paper office labels designed for laser printers. We do not recommend using

vinyl or polyester labels or any card stock with the Optra K 1220 printer.

Always feed labels from the manual feed tray or the optional multipurpose feeder. The multipurpose feeder can hold

up to 30 sheets of labels.

The following table lists the maximum weights supported.

Printer specifications 153

Paper source

Card stock Labels

Index Bristol Tag Cover Paper Vinyl

Multipurpose feeder — — —

150 g/m

—

Manual feed tray — — —

150 g/m

—

For paper and transparency specifications, see the printer User's Guide.

Labels Width: 210–216 mm (8.3–8.5 in.)

Length: 279–356 mm (11–14 in.)

Weight:

120–150 g/m

(32–40 lb)

Label guidelines

When printing on labels:

• From the operator panel or from MarkVision, set the Paper Type to Labels. Set the Paper Weight to either Normal

or Heavy for optimum print quality.

• To minimize curl, make sure the rear exit bin is open so the labels feed straight out the back of the printer.

• Do not print a large number of labels continuously.

• Do not use labels that have exposed adhesive on the label sheets.

Optra M410, M412

The Optra M410 and Optra M412 print on card stock and many labels designed for use with laser printers.

The following tables list the weights supported by the multipurpose feeder and the 250‑sheet label tray, P/N 4K00293.

Paper source

Card stock

Index Bristol Tag Cover

Multipurpose feeder

Up to 199 g/m

Up to 163 g/m

Up to 176 g/m

250‑sheet label tray ———

Printer specifications 154

Paper source

Labels

Paper Vinyl Dual web Integrated

Multipurpose feeder

120–180 g/m

260–300 g/m

140–180 g/m

140–175 g/m

250‑sheet label tray

120–180 g/m

260–300 g/m

140–180 g/m

140–175 g/m

The 250‑sheet label tray option accommodates plain paper, transparencies, simple paper labels, dual web paper labels,

and vinyl labels. Lightweight plain paper (less than 20 lb. bond) is not supported.

To reliably feed lightweight plain paper and some lightweight labels, use the standard 250‑sheet input tray that comes

with your printer.

The label tray can hold up to 100 labels.

The optional 500‑sheet drawer should only be used to feed paper; it does not support card stock and label printing.

You can try occasional label printing from Tray 1, but we recommend you use the multipurpose feeder.

For paper and transparency specifications, see the printer User's Guide.

Source Print media Capacity

Multipurpose feeder Labels

Card stock

30 labels

10 sheets card stock

250‑sheet label tray Labels 100 labels

Card stock and label guidelines

When printing on labels:

• From the operator panel or MarkVision Professional, set the Paper Type to Labels.

• Do not load labels together with paper or transparencies in the same paper source.

• To minimize curl, make sure the rear exit bin is open so the labels feed straight out the back of the printer.

• Do not use label sheets with a slick backing material.

• Do not print within 1 mm (0.040 in.) of the die-cut.

• Use full label sheets. Partial sheets may cause labels to peel off during printing, resulting in a paper jam. Partial

sheets will also contaminate your printer and your cartridge with adhesive, and could void your printer and cartridge

warranties.

• Do not print within 1 mm (0.040 in.) of the edge of the label, of the perforations, or between die-cuts of the label.

• Do not use label sheets that have adhesive to the edge of the sheet. We recommend zone coating of the adhesive

at least 1 mm (0.040 in.) away from edges. Adhesive material will contaminate your printer and could void your

warranty.

• If zone coating of the adhesive is not possible, a 3‑mm (0.125‑in.) strip should be removed on the leading and driver

edge, and a non‑oozing adhesive should be used.

• Remove a 3‑mm (0.125‑in.) strip from the leading edge to prevent labels from peeling inside the printer.

• Portrait orientation is preferred, especially when printing bar codes.

• Do not use labels that have exposed adhesive.

• For best results when using the multipurpose feeder, dual web and integrated labels should be fed paper‑end first.

• For best results when using the 250‑sheet label tray, dual web and integrated labels should be fed label‑end first.

Printer specifications 155

When printing on card stock:

• From the operator panel or MarkVision Professional, set the Paper Type to Card Stock.

• Do not use preprinted card stock manufactured with chemicals that may contaminate the printer.

• Do not use card stock that is creased. It may cause paper jams.

• To minimize curl, make sure the rear exit bin is open so the card stock feeds straight out the back of the printer.

• We recommend the use of grain short card stock.

For more information, see

“Maintenance procedures” on page 14.

Optra N

Limit label printing to occasional use of paper office labels designed for laser printers. We do not recommend using

vinyl or polyester labels.

Always feed labels from the multipurpose tray. The multipurpose tray can hold up to 50 sheets of labels.

The Optra N supports print materials up to 128 g/m

(34 lb).

The following table lists the maximum weights supported by the multipurpose tray.

Paper source

Card stock Labels

Index Bristol Tag Cover Paper Vinyl

Multipurpose Tray — — —

128 g/m

—

For paper and transparency specifications, see the printer User's Guide.

Labels Width: 210–216 mm (8.3–8.5 in.)

Length: 279–356 mm (11–14 in.)

Weight:

120–128 g/m

(32–34 lb)

Thickness: 0.13–0.20 mm (0.005–0.008 in.)

Smoothness: 100–400 Sheffield*

* 150–250 Sheffield is optimal. Using media higher than 300 Sheffield could result in printing degradation.

Printer specifications 156

Optra S

Optra S 1250, S 1255, S 1620, S 1625, S 1650, S 1855, S 2420, S 2450, S 2455,

Se 3455

The following table lists the maximum weights supported by each of the printer trays.

Print material

Range or maximum weight supported

250‑sheet and 500‑sheet trays

Multipurpose feeder and optional

250‑sheet drawer

Paper

(grain long)

Xerographic or business paper

60–176 g/m

(16–47 lb bond)

60–135 g/m

(16–36 lb bond)

Card stock

(grain long

)

Index Bristol

163 g/m

(90 lb) 120 g/m

(67 lb)

Tag

163 g/m

(100 lb) 120 g/m

(74 lb)

Cover

176 g/m

(65 lb) 135 g/m

(50 lb)

Card stock

(grain short

)

Index Bristol

199 g/m

(110 lb) 163 g/m

(90 lb)

Tag

203 g/m

(125 lb) 163 g/m

(100 lb)

Cover

216 g/m

(80 lb) 176 g/m

(65 lb)

Labels Paper

180 g/m

(48 lb bond) 163 g/m

(43 lb bond)

Dual‑Web Paper

180 g/m

(48 lb bond) 163 g/m

(43 lb bond)

Vinyl

300 g/m

(92 lb liner) 260 g/m

(78 lb liner)

Polyester

220 g/m

(59 lb bond) 220 g/m

(59 lb bond)

Integrated forms

Pressure sensitive area

140–175 g/m

140 to 175 g/m

Paper base (grain long)

75–135 g/m

(20–36 lb bond)

75–135 g/m

(20–36 lb bond)

See “Grain orientation” on page 17 for specific recommendations.

Pressure‑sensitive area must enter the printer first for grain short paper.

For paper and transparency specifications, see the printer User's Guide.

Labels Thickness: 0.102–0.305 mm (0.004–0.012 in.)

Smoothness: 100–400* Sheffield

Printer specifications 157

* 150–250 Sheffield is optimal. Using media higher than 300 Sheffield could result in printing degradation.

Card stock Weight:

Up to 199 g/m

Index Bristol (90 lb)

Up to 203 g/m

Tag (100 lb)

The following table indicates the paper sizes each tray supports.

Source

Standard sizes

(width x length)

Universal sizes

(width x length)

Minimum Maximum Minimum Maximum

250‑sheet tray

500‑sheet tray

148 x 210 mm

(5.83 x 8.27 in.)

215.9 x 355.6 mm

(8.5 x 14 in.)

139.7 x 210 mm

(5.5 x 8.27 in.)

215.9 x 355.6 mm

(8.5 in. x 14 in.)

Multipurpose feeder 148 x 210 mm

(5.83 x 8.27 in.)

215.9 x 355.6 mm

(8.5 x 14 in.)

69.85 x 127 mm

(2.75 in. x 5 in.)

229 x 355.6 mm

(9.01 x 14 in.)

If you load paper that is narrower than 148 mm (5.83 in.) in the multipurpose feeder (for example, 3 x 5‑inch index cards),

set the MP Feeder Size menu item to Universal.

See your printer documentation for specifications on tray capacities.

Standard trays and special media trays

The Optra S paper feeding mechanism uses advanced technology that enhances feeding reliability. The standard Optra S

tray, which holds 250 or 500 sheets of bond paper, reliably feeds all paper and specialty media designed according to

the guidelines specified under

“Dimensions” on page 9. If specialty media does not conform to these guidelines, we

recommend using the 250‑sheet special media tray option, P/N 43H5410, to prevent double sheet feeds.

For those difficult‑to‑print sizes, such as 3 x 5‑inch index cards, Lexmark offers a variety of special media tray and drawer

options.

Source Part number

250‑Sheet Special Media Tray 43H5535

250‑Sheet Special Media Drawer 43H5540

250‑Sheet Universally Adjustable Tray 43H5525

250‑Sheet Universally Adjustable Drawer 43H5524

500‑Sheet Special Media Tray 11K1886

500‑Sheet Special Media Tray + Drawer 11K1902

400‑Sheet Universally Adjustable Tray 11K1904

400‑Sheet Universally Adjustable Tray + Drawer 11K1903

Card stock and label guidelines

You can use many labels designed for laser printers with your Optra S printer. When printing on labels, use the printer

operator panel to set the Paper Type to Labels in the Paper Menu. For vinyl and other heavy labels, set the Labels

Weight (under the Paper Weight menu) to Heavy, and set the Labels Texture (under the Paper Texture menu) to Smooth.

Do not load labels together with paper or transparencies in the same paper tray. Combining print materials can cause

feeding problems.

Printer specifications 158

The information in the specification tables is intended to convey general guidelines for tray and drawer selection. The

material type, rigidity, sizing, perforations, die-cuts, and surface influence the performance reliability.

The duplex option supports all paper weights and types that the printer supports, except for transparencies and

envelopes. Duplexing of specially designed labels is supported in the Optra S1855 printer.

You may notice skew or print registration problems if you feed materials over 135 g/m

from the multipurpose feeder

or the optional 250‑sheet drawer. You may notice similar problems if you feed materials over 176 g/m

from the primary

250‑sheet tray or the optional 500‑sheet drawer.

When feeding labels, the number of labels per sheet can affect registration more than basis weight. Typically, the more

labels per sheet, the better the registration.

Ordering special supplies for label printing

Labels are one of the most difficult print materials for laser printers to handle. To optimize printer performance, use

the special label fuser cleaner for printers dedicated to label printing.

To get the special label oil fuser cleaner (to use with simplex labels and vinyl labels), order print cartridge P/N 1382929.

If you need additional label fuser cleaners of this type (packaged separately from the print cartridge), order

P/N 43H0814. If you are duplexing other jobs, do not use the special label fuser cleaner that comes with this cartridge.

Duplexing of specially designed duplex labels is only supported in the S1855. You must also use a specially designed

wax fuser cleaner (P/N 99A1082) with this application. The cartridge containing this special wax fuser cleaner should

be ordered when cartridge replacements are needed.

Print cartridge part number

Yield

(average)

Coverage

(approximate)

1382929 Prebate

(cartridge for special label machine use)

17,600 pages 5%

For more information, see the following:

• “Pick roller technology” on page 11

• “Maintenance procedures” on page 14

• “Troubleshooting” on page 14

Optra SC 1275

Limit label printing to occasional use of paper office labels designed for laser printers. We do not recommend using

vinyl or polyester labels.

Printer specifications 159

Limit card stock printing to occasional use of A4‑ or letter‑size Index Bristol or Tag. The Optra SC supports stock up to

163 g/m

(43 lb).

Always feed card stock and labels from the multipurpose feeder. The multipurpose feeder can hold up to 75 sheets of

card stock or labels.

The following table lists the maximum weights supported by the multipurpose feeder.

Paper source

Card stock Labels

Index Bristol Tag Cover Paper Vinyl

Multipurpose feeder

163 g/m

—

163 g/m

—

For paper and transparency specifications, see the printer User's Guide.

Labels Width: 210–216 mm (8.3–8.5 in.)

Length: 279–297 mm (11–11.7 in.)

Weight:

120–163 g/m

(32–43 lb)

Thickness: 0.13–0.20 mm (0.005–0.008 in.)

Smoothness: 100–400 Sheffield*

* 150–250 Sheffield is optimal. Using media higher than 300 Sheffield could result in printing degradation.

Card stock Weight:

Up to 163 g/m

Index Bristol (90 lb)

Up to 163 g/m

Tag (100 lb)

Optra T

The Optra T prints on many labels designed for use with laser printers.

The following table lists the maximum weights supported by the trays and the multipurpose feeder.

Printer specifications 160

Print material

Range or maximum weight supported

250‑sheet and 500‑sheet trays

Multipurpose feeder and

optional 250‑sheet drawer

Paper

(grain long)

Xerographic or business paper

60–176 g/m

(16–47 lb bond)

60–135 g/m

(16–36 lb bond)

Card stock

(grain long

)

Index Bristol

163 g/m

(90 lb) 120 g/m

(67 lb)

Tag

163 g/m

(100 lb) 120 g/m

(74 lb)

Cover

176 g/m

(65 lb) 135 g/m

(50 lb)

Card stock

(grain short

)

Index Bristol

199 g/m

(110 lb) 163 g/m

(90 lb)

Tag

203 g/m

(125 lb) 163 g/m

(100 lb)

Cover

216 g/m

(80 lb) 176 g/m

(65 lb)

Labels Paper

180 g/m

(48 lb bond) 163 g/m

(43 lb bond)

Dual‑Web Paper

180 g/m

(48 lb bond) 163 g/m

(43 lb bond)

Vinyl

300 g/m

(92 lb liner) 260 g/m

(78 lb liner)

Polyester

220 g/m

(59 lb bond) 220 g/m

(59 lb bond)

Integrated forms

Pressure sensitive area

140–175 g/m

Paper base (grain long)

75–135 g/m

(20–36 lb bond)

75–135 g/m

(20–36 lb bond)

See “Grain orientation” on page 17 for specific recommendations.

Pressure‑sensitive area must enter the printer first for grain short paper.

For paper and transparency specifications, see the printer User's Guide.

The following table indicates the paper sizes each tray supports.

Source

Standard sizes

(width x length)

Universal sizes

(width x length)

Minimum Maximum Minimum Maximum

Standard tray,

250‑sheet drawer,

500‑sheet drawer

148 x 210 mm

(5.83 x 8.27 in.)

215.9 x 355.6 mm

(8.5 x 14 in.)

139.7 x 210 mm

(5.5 x 8.27 in.)

215.9 x 355.6 mm

(8.5 in. x 14 in.)

Multipurpose

feeder*

148 x 210 mm

(5.83 x 8.27 in.)

215.9 x 355.6 mm

(8.5 x 14 in.)

69.85 x 127 mm

(2.75 in. x 5 in.)

229 x 355.6 mm

(9.01 x 14 in.)

* If you load paper that is narrower than 148 mm (5.83 in.) in the multipurpose feeder (for example, 3 x 5‑inch index cards),

set the MP Feeder Size menu item to Universal.

Labels Thickness: 0.102–0.305 mm (0.004–0.012 in.)

Smoothness: 100–400* Sheffield

* 150–250 Sheffield is optimal. Using media higher than 300 Sheffield could result in printing degradation.

Printer specifications 161

Card stock Weight:

Up to 199 g/m

Index Bristol (90 lb)

Up to 203 g/m

Tag (100 lb)

Standard trays and special media trays

The Optra T paper feeding mechanism uses advanced technology that enhances feeding reliability. The standard Optra

T tray, which holds 250 or 500 sheets of bond paper, reliably feeds all media tested according to the guidelines specified

under

“Dimensions” on page 9.

For those difficult‑to‑print sizes, such as 3 x 5‑inch index cards, Lexmark offers a variety of special media trays and

drawers.

Note: Optional 250‑sheet Universally Adjustable Trays designed for the Lexmark T printer family support forms with

a minimum length of 5 inches when installed either in the integral tray location or in a 250‑sheet drawer under a

250‑sheet integral tray. The 250‑sheet Universally Adjustable Tray does not support forms shorter than 7 inches on a

T522, T620, T622, T630, or T632. Optional 500‑sheet Universally Adjustable Trays support forms with a minimum

length of 7 inches.

Source Part number

250‑Sheet Special Media Tray 11K1572

250‑Sheet Special Media Drawer 11K1573

250‑Sheet Universally Adjustable Tray 11K1574

250‑Sheet Universally Adjustable Drawer 11K1878

500‑Sheet Special Media Tray 11K1921

500‑Sheet Special Media Tray + Drawer 11K1922

400‑Sheet Universally Adjustable Tray 11K1941

400‑Sheet Universally Adjustable Tray + Drawer 11K1942

Card stock and label guidelines

Labels are one of the most difficult print materials for laser printers. A special fuser cleaner should be used for label

applications to optimize feed reliability. See your printer documentation for information on ordering additional label

fuser cleaners.

Printing labels on the Optra T requires a special label fuser cleaner that prevents duplexing.

It is recommended that when you run vinyl labels, you install a special oil fuser cleaner, P/N 99A0725. When you order

a new cartridge, be sure to order the cartridge that will include the correct fuser cleaner.

It is possible to duplex certain labels that have been specifically designed for this application. To duplex labels, consult

the Lexmark “Converter Lists” to see which converters have successfully developed this type of label, and you must

install a special fuser wiper. The wax wiper that is used with the Optra T is P/N 99A1082.

When printing on labels:

• Using the printer operator panel, set the Paper Type to Labels in the Paper Menu. For vinyl and other heavy labels,

set the Labels Weight (under the Paper Weight menu) to Heavy, and set the Labels Texture (under the Paper Texture

menu) to Smooth.

• Do not load labels together with paper or transparencies in the same paper tray. Combining print materials can

cause feeding problems.

Printer specifications 162

• Use full label sheets. Partial sheets may cause labels to peel off during printing, resulting in a paper jam. Adhesive

material may contaminate your printer. It could also void your printer and cartridge warranties.

When printing on card stock:

• Set the Paper Type to Card Stock in the Paper Menu.

• Do not use card stock that is creased. It may cause paper jams.

When feeding labels, the number of labels per sheet can affect registration more than basis weight. Typically, the more

labels per sheet, the better the registration.

For more information, see the following:

• “Pick roller technology” on page 11

• “Grain orientation” on page 17

• “Maintenance procedures” on page 14

• “Troubleshooting” on page 14

Optra W810

Limit label printing to occasional use of A4‑ or letter‑size paper labels designed for laser printers. We do not recommend

using vinyl or polyester labels.

The Optra W810 supports stocks up to 163 g/m

(43 lb). Always feed labels and card stock from Tray 1, which holds up

to 50 sheets of labels or card stock.

The following table lists the maximum weights supported by Tray 1.

Paper source

Card stock Labels

Index Bristol Tag Cover Paper Vinyl

Tray 1

163 g/m

—

163 g/m

—

For paper and transparency specifications, see the printer User's Guide.

Labels Width: 210–216 mm (8.3–8.5 in.)

Length: 279–356 mm (11–11.7 in.)

Weight:

120–128 g/m

(32–34 lb.)

Thickness: 0.13–0.20 mm (0.005–0.008 in.)

Smoothness: 100–400 Sheffield*

* 150–250 Sheffield is optimal. Using media higher than 300 Sheffield could result in printing degradation.

Printer specifications 163

Card stock Width: 210–216 mm (8.3–8.5 in.)

Length: 279–356 mm (11–11.7 in.)

Weight:

Up to 163 g/m

Index Bristol (90 lb)

Card stock and label guidelines

When printing on labels:

• Set the Paper Type to Labels in the Paper Menu.

• Do not use label sheets with a slick backing material.

• Do not print within 1 mm (0.040 in.) of the die-cut, the edge of the label, the perforations, or between the die-cuts.

• Use full label sheets. Partial sheets may cause labels to peel off during printing, resulting in a paper jam.

• Do not use label sheets that have adhesive to the edge of the sheet. We recommend zone coating of the adhesive

at least 1 mm (0.040 in.) away from the edges. Adhesive material may contaminate your printer and could void

your warranty.

When printing on card stock:

• Set the Paper Type to Plain Paper. The Optra W810 treats card stock the same as Plain Paper. It does not adjust the

print speed or fuser temperature when the Paper Type is set to Card Stock.

• Do not use card stock that is creased. It may cause paper jams.

• We recommend the use of grain long card stock.

Printer specifications 164

Glossary

Adhesive contamination Migration of adhesive away from a label, which can cause printer contamination.

Also known as glue contamination.

Anvil cuts Cuts that penetrate both the face stock and the liner of a label.

Auto compensator A gear‑driven pick arm suspended by a counterbalance spring that allows the

printer to automatically adjust the pick force necessary for different types of print

materials.

Back splits Also known as back slits or liner cuts. Cuts through the backside of the liner. Back

slits increase the potential for adhesive contamination.

Backup roll contamination Toner contamination of the fuser's backup roll. Particularly applies to vinyl,

plastic, and paper labels. Slick backings are harder to feed and increase toner

buildup in the fuser.

Basis weight Weight in pounds of a specific number of sheets of paper or stock in a standard

size for that particular material.

Beam strength Also known as column strength. Refers to how well the material is able to support

itself and remain flat and straight during the printing process.

Butt cut Cut flush to one another, with no extra area between. This cut does not extend

through the liner. Butt cut labels may or may not have an edge matrix removed.

Calendering The process of moving paper through metal rolls during manufacturing to smooth

and gloss the surface of the paper.

Clipping Also known as buckler damage. A notching or slight folding of the corner of the

stock placed under the corner buckler of the paper tray.

Conversion The process that turns base stock into cut‑sheet products designed for specific

applications. Conversion includes cutting the base stock to size, perforating the

stock, die‑cutting, and applying inks and topcoats.

Converters Print material suppliers who take the base stock from the manufacturer and

convert it into cut sheet products.

Corner buckler The metal tab at the corner of a paper tray that helps the printer separate one

sheet of paper from the stack during the pick process.

Curl Waviness or curvature at the edge of the material that is generally moisture

related.

Cut sheet Single piece (page) of paper or label stock.

Debossing Process of pressing an image down into the surface of the label or card stock. See

“Embossing” on page 166.

Delamination The peeling of labels off the backing during the printing process.

Die‑cut Labels: Cut of material (face stock) to form individual labels on sheet. Cuts do not

penetrate the liner. Card Stock: Cuts made with dies to create the shapes wanted

in the stock. Cuts may or may not go completely through the stock. See

“Ties” on

page 167.

Glossary 165

Driver edge For printers that use a fixed reference for feeding paper through the paper path

(as opposed to printers that center paper in the path), the edge of the print

material that is positioned next to the hardware reference and that is driven by

the rollers in the printer. For most Lexmark printers, the driver edge is the left

edge of a portrait page.

Embossing Process of raising the surface of the base material by stamping an image or design

with an embossing machine. The machine has a roll with a raised image on the

surface. As the print material passes through the machine, the image is pressed

into the material. See

“Debossing” on page 165.

Feed How well the stock moves out of the paper tray and through the printer.

Fiber content The material used to manufacture the paper. Most high‑quality xerographic

paper is made from 100% chemically pulped wood. This content provides the

paper with a high degree of stability resulting in fewer paper feeding problems

and better print quality. Paper containing fibers such as cotton have

characteristics that can result in degraded paper feeding.

Fuse grade Qualitative measurement of the adhesion of toner to the printed sheet.

Fusing Printer process of melting toner and adhering it to the print material.

Glue contamination See

“Adhesive contamination” on page 165.

Grain The orientation of the fibers in the print material. Grain short indicates the fibers

run the width of the paper. Grain long indicates the fibers run the length of the

paper.

Ink contamination Transfer of ink from a form to the printer's pick mechanism or fuser assembly,

which can cause printer contamination.

Ironing A mechanical process used during conversion to flatten stock.

Laser ink Inks that can withstand fuser temperatures of 225°C (437°F) and pressures to 25

psi without contaminating the printer or releasing hazardous fumes.

Laser‑perfs Small perforations (20 to 30 perfs per inch) that create little paper dust and debris

and do not normally cause nesting. Also known as micro‑perfs or data‑perfs.

Leading edge The edge of the print material that enters the printer paper path first.

Matrix Unneeded portions of die‑cut stock around labels. A stripped matrix is one that

is removed to make it easier to peel labels from the liner.

Micro‑perfs See

“Laser‑perfs” on page 166.

Moisture content The amount of moisture in the paper, which affects both print quality and paper

feeding. Leave paper in its original wrapper until you are ready to use it. This

limits the exposure of the paper to moisture changes that can damage the paper.

Nesting To fit compactly together; to interlock; to stick together.

Offset powder A powder applied during some printing processes to help dry inks.

Oil bleed Migration of materials from the substrate or the adhesive out to the face. This

generally occurs in aged materials or materials exposed to extreme temperature

changes. Also known as penetration, bleed through, and bleed.

Ooze Migration of adhesive away from labels, which can cause printer contamination.

Perforation Line of very small holes or slots punched to facilitate tearing. See also

“Laser‑perfs” on page 166.

Glossary 166

Pick The mechanical action the printer performs to remove one sheet of material from

the tray.

Pick roller The roller that assists in picking a sheet of material from the tray.

Pull strength See

“Release” on page 167.

Release The ability of adhesive to resist label peeling during the printing process.

Rollback The lifting of labels from the backing during the printing process. Also known as

butterflying.

Roll‑over Bending of the paper edge during conversion due to a dull cutting knife.

Semi‑liquid Having characteristics of both liquid and solid.

Shear strength Cohesive strength of the adhesive.

Shelf talkers Small signs that hang over or next to a regular shelf label. Shelf talkers may be

constructed of a pressure‑sensitive material or card stock.

Sizing Additives applied to paper (internally or externally) that improve offset printing

qualities and resistance to liquids.

Skew Slant of printed lines in reference to the edge of the paper; due to paper moving

through the printer in something other than a straight path.

Smoothness The degree of smoothness of the print material. If the paper is too rough, the

toner does not fuse to the paper properly, resulting in poor print quality. If the

paper is too smooth, it can cause paper feeding problems in the printer.

Smoothness is measured in Sheffield points; lower values indicate smoother

paper.

Splatter The appearance of black specks around a printed image. Generally related to

printing on stock that is too heavy or has a surface that repels toner.

Stacking How well the paper stacks in the output bin.

Stringers Small bits of adhesive found on top of a pressure‑sensitive material at the die‑cut

and perforated areas. Stringers are indications of a dull blade and are related to

the shear strength of the adhesive.

Stripped edge matrix Labels with a portion of the area around the outer edge of the cut sheet removed.

Supercalendering A process where paper passes through heated, polished steel and compressed

cotton rolls that "iron" the material to a high gloss, polished finish.

Talkers Printed or handwritten signs used to advertise specials or to draw attention to a

particular product.

Tenting The creasing of perforated material when it is flexed.

Thermography A printing process that raises the ink image or design above the surface of the

base material. Also known as electro

‑

thermography.

Ties Small areas along perforations or die‑cuts in the face material of a label

(pressure‑sensitive material), or in card stock, which are not cut through. Ties

help stabilize the form and prevent tearing at the perforations and die‑cuts.

Toner The material that adheres to the paper or print material to create the printed

image.

Total strip matrix Labels that have the unneeded portion of the die‑cut stock around the labels,

including a portion between the labels, removed to make it easier to peel labels

from the backing.

Glossary 167

Vellum finish A finish with a rough surface similar to eggshell and antique finishes. A vellum

finish is relatively absorbent, providing good ink penetration.

Wash boarding Waviness in the stock that gives a rippled appearance to the material; generally

moisture related.

Zone coating Placing adhesive in selected areas only. Allows no adhesive areas along edge of

labels. Also known as patterned adhesive, pattern coated, dry lap, separator, strip

coated.

Glossary 168

Index

adhesives

contamination 20, 23, 25

integrated forms 25

label component 23

backing 23

bar codes 11

basis weight 9, 16

butt cut labels 25

card stock

coatings 18

design factors 9

grain orientation 17

recommendations 16

thickness 16

weights 9, 16

carrier 23

chaff 23, 147

coatings 18

contamination 20, 23, 25

converters 8

curl 10, 17

cut sheet paper labels 25

debossing 11

designing labels 9, 25

die‑cut labels 25

die‑cuts 10

dimensions 9

distributors 8

dual web forms 25

duplexing labels 20

embossing 9

environmental factors 9

face sheet 23

fiber content 166

finishes 18, 23

form design 11, 9

fumes 9, 25

fuser cleaner

Optra Plus and 4039 printers 147

Optra S 159

grain orientation 17

humidity 9

industry 8

inks (preprinted stock) 10

integrated forms 31

ironing 10

label characteristics 20

label components

adhesives 24

face sheets 25

liners 23

topcoats 25

label fuser cleaner (Optra S) 159

labels

construction 23, 20

design 25, 20

dual web forms 29

duplexing 20

integrated forms 31

printer maintenance 20

printing 20

vinyl and polyester labels 30

labels, printing on 20

laser printers 7

liners 23

maintenance procedures 14

manufacturers 8

matrix

defined 166

stripped edge 25

total strip 26, 25

metallics 11

moisture content 166

notices 2

oil bleed 31

orientation 11

paper and label industry 8

paper dust 24, 147

perforations 10

pick roller 11

polyester labels 30

preprinted stock 10

primary rib pattern design

guidelines 22

print is blurred or out of focus 14

print volumes 8

printing on labels 20

printing shows voids 14

reference edge alignment 22

sizing 29

smoothness 24

stacking in output bin 31

stripped edge matrix 23, 25

supercalendering 24

supported laser printers 7

technical assistance 7, 9

temperature 9

testing print material 8

thermography inks 10

toner rubs off 14

topcoats 25

troubleshooting 14

vinyl labels 25

volume printing 8

Index 169

weight, basis 9

weights, card stock

comparison 0

zone coating

adhesives 25

integrated forms 31

labels 26

Index 170